Which switch would STP choose to become the root bridge in the selection process?() A.32768: 11-22-33-44-55-66B.32768: 22-33-44-55-66-77C.32769: 11-22-33-44-55-65D.32769: 22-33-44-55-66-78
Which switch would STP choose to become the root bridge in the selection process?()
A.32768: 11-22-33-44-55-66
B.32768: 22-33-44-55-66-77
C.32769: 11-22-33-44-55-65
D.32769: 22-33-44-55-66-78
相关考题：
Why would the Ezonexam administrator change the value of the spanning-tree priority of a switch?A. in order to optimize the path that frames take from source to destinationB. to increase the priority so a designated port will become a root portC. to increase the BID, so the switch is more likely to become root bridgeD. in order to allow VLANs to be sent from one switch to another across a single linkE. to force a given switch to become an STP serverF. None of the above
You want to influence the root bridge selection within the Ezonexam LAN. Which two values are used by spanning tree protocol to elect a root bridge? (Choose two.)A. Amount of RAMB. Speed of the linksC. IOS VersionD. MAC AddressE. Bridge PriorityF. IP AddressG. Router ID
Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?() A.Switch3B.Switch4C.Switch2D.Switch1
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree Protocol IEEE 802.1D？ （）A、Designated Root CostB、bridge ID priorityC、max ageD、bridge ID MAC addressE、Designated Root PriorityF、forward delay
In the Cisco FabricPath domain， one switch becomes the root for the multidestination tree. Cisco FabricPath switches compare which three parameters to select the root？ （）A、 Root priorityB、 System IDC、 Bridge IDD、 Switch IDE、 Port IDF、 Subswitch ID
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）A、Designated Root CostB、bridge ID priorityC、max ageD、bridge ID MAC addressE、Designated Root PriorityF、forward delay
Which two of the following values does STP take into consideration when it elects the root bridge?（）A、The BPDU version numberB、The access layer bridge settingC、The Bridge IDD、The spanning-tree update numberE、The bridge priorityF、The VLAN number
Why would an administrator change the value of the spanning-tree priority of a switch?（）A、in order to optimize the path that frames take from source to destinationB、to increase the priority so a designated port will become a root portC、to increase the BID, so the switch is more likely to become root bridgeD、in order to allow VLANs to be sent from one switch to another across a single linkE、to force a given switch to become an STP server
Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?（）A、Switch3B、Switch4C、Switch2D、Switch1
Which three options are considered in the spanning-tree decision process？（）A、lowest root bridge IDB、lowest path cost to root bridgeC、lowest sender bridge IDD、highest port IDE、highest root bridge IDF、highest path cost to root bridge
Which three statements about STP timers are true？（）A、STP timers values （hello， forward delay， max age） are included in each BPDU.B、A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.C、To successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.D、If any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.E、On a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.F、The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.
Which switch would STP choose to become the root bridge in the selection process?（）A、32768: 11-22-33-44-55-66B、32768: 22-33-44-55-66-77C、32769: 11-22-33-44-55-65D、32769: 22-33-44-55-66-78
Which two values are used by Spanning Tree Protocol to elect a root bridge (Choose two.)（）。A、amount of RAMB、bridge priorityC、IOS versionD、IP addressE、MAC addressF、speed of the links
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。A、Establish a direct link from the switch to all other switches in the network.B、Assign the switch a higher MAC address than the other switches in the network have.C、Configure the switch so that it has a lower priority than other switches in the network.D、Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.E、Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
Which statement is correct about RSTP port roles？（）A、The designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.B、The disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.C、The backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable， active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.D、The root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.
Refer to the output shown on switch SW1 below： VLAN 1 bridge priority set to 8192. VLAN 1 bridge max aging time set to 20.VLAN 1 bridge hello time set to 2. VLAN 1 bridge forward delay set to 15. Switch is now the root switch for active VLAN 1. What command would you enter to reproduce this output？
多选题Which three options are considered in the spanning-tree decision process？（）Alowest root bridge IDBlowest path cost to root bridgeClowest sender bridge IDDhighest port IDEhighest root bridge IDFhighest path cost to root bridge
单选题Which statement is correct about RSTP port roles？（）AThe designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.BThe disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.CThe backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable， active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.DThe root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.
单选题Which statement describes a spanning-tree network that has converged?（）AAll switch and bridge ports are in the forwarding state.BAll switch and bridge ports are assigned as either root or designated ports.CAll switch and bridge ports are in either the forwarding or blocking state.DAll switch and bridge ports are either blocking or looping.
单选题Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?（）ASwitch3BSwitch4CSwitch2DSwitch1
单选题Why would an administrator change the value of the spanning-tree priority of a switch?（）Ain order to optimize the path that frames take from source to destinationBto increase the priority so a designated port will become a root portCto increase the BID, so the switch is more likely to become root bridgeDin order to allow VLANs to be sent from one switch to another across a single linkEto force a given switch to become an STP server
单选题Which switch would STP choose to become the root bridge in the selection process?（）A32768: 11-22-33-44-55-66B32768: 22-33-44-55-66-77C32769: 11-22-33-44-55-65D32769: 22-33-44-55-66-78
多选题Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree Protocol IEEE 802.1D？ （）ADesignated Root CostBbridge ID priorityCmax ageDbridge ID MAC addressEDesignated Root PriorityFforward delay
多选题Which three statements about STP timers are true？（）ASTP timers values （hello， forward delay， max age） are included in each BPDU.BA switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.CTo successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.DIf any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.EOn a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.FThe root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.
问答题Refer to the output shown on switch SW1 below： VLAN 1 bridge priority set to 8192. VLAN 1 bridge max aging time set to 20.VLAN 1 bridge hello time set to 2. VLAN 1 bridge forward delay set to 15. Switch is now the root switch for active VLAN 1. What command would you enter to reproduce this output？
多选题Which two of the following values does STP take into consideration when it elects the root bridge?（）AThe BPDU version numberBThe access layer bridge settingCThe Bridge IDDThe spanning-tree update numberEThe bridge priorityFThe VLAN number
多选题Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）ADesignated Root CostBbridge ID priorityCmax ageDbridge ID MAC addressEDesignated Root PriorityFforward delay