Which two locations can be configured as a source for the IOS image in the boot system command?() A.RAMB.NVRAMC.flash memoryD.HTTP serverE.TFTP serverF.Telnet server
Which two locations can be configured as a source for the IOS image in the boot system command?()
A.RAM
B.NVRAM
C.flash memory
D.HTTP server
E.TFTP server
F.Telnet server
相关考题：
What will cause a Ezonexam router to enter setup mode? (Choose two)A. The configuration file is missing in NVRAM.B. The configuration register is set to 0x2100.C. Boot system commands are misconfigured in the running-configuration.D. The setup command was issued from the privileged mode prompt.E. The IOS is missing.F. The IOS is corrupt.
Which command do you use to display the messages seen during the last system boot?() A. show system boot-messagesB. show chassis messagesC. show file system boot-messagesD. show boot-log messages
After mirroring rootvg, a system administrator wants to validate that the system will boot correctly.Which of the following tasks must be performed before changing the boot order?() A.Run a bosboot -a commandB.Mirror the hd5 on the two disksC.Set up another service mode bootlistD.Check the disks using a lsvg -p rootvg command
Which two of these statements correctly describe classic PIM-SM？（）A、The IOS default is for a last-hop router to trigger a switch to the shortest path tree as soon as a new source is detected on the shared tree.B、The IOS default is for every one of the routers on the shared tree to trigger a switch to the shortest path tree as soon as a new source is detected on the shared tree.C、The default behavior of switching to the shortest path tree as soon as a new source is detected on the shared tree can be disabled by setting the value in the ip pim spt-threshold command to "infinity."D、The default behavior of switching to the shortest path tree as soon as a new source is detected on the shared tree can be disabled by setting the value in the ip pim spt-threshold command to "zero."
When resetting a Catalyst Express switch to factory default settings， which three options are available from the Software Recovery window？（）A、Boot to a password recovery windowB、Boot with the factory default imageC、Erase the system configuration and boot with the factory default IOS imageD、Erase the system configuration and boot from a TFTP-supplied IOS imageE、Erase the System Configuration
What is the main reason for using the "ip ips deny-action ips-interface" IOS command？（）A、 To selectively apply drop actions to specific interfacesB、 To enable IOS to droptraffic for signatures configured with the Drop actionC、 To support load-balancing configurations in which traffic can arrive via multipleinterfaces D、 This is nota valid IOS command
User defined locale files can be stored in which two locations?（）A、DRAMB、SDRAMC、CME flash，slot0D、CUE flash，slot0E、TFTP directory specified by cnf-file location command
Which two locations can be configured as a source for the IOS image in the boot system command?（）A、RAMB、NVRAMC、flash memoryD、HTTP serverE、TFTP serverF、Telnet server
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）A、Router1 has specific boot system command that instruct it to load IOS from TFTP server.B、Router1 is acting as a TFTP server for other routers.C、Router1 cannot locate a valid IOS image in flash memory.D、Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.E、Cisco routers will first attempt to load a image from TFTP for management purposes.
After mirroring rootvg, a system administrator wants to validate that the system will boot correctly. Which of the following tasks must be performed before changing the boot order?（）A、Run a bosboot -a commandB、Mirror the hd5 on the two disksC、Set up another service mode bootlistD、Check the disks using a lsvg -p rootvg command
Which command is used by the system boot process to determine what resources are available to the system？（）A、diagB、lscfgC、mpcfgD、cfgmgr
Users complain they cannot communicate with a server. The system administrator suspects there may be a problem with the Ethernet adapter or with the way it is configured. Which command can be run to verify the adapter is configured correctly？（）A、netstat -inB、ifconfig -aC、arp -aD、cfgmgr
A user reports a corrupted boot logical volume. In order to recreate the contents of the boot logical volume which of the following procedures should the user be advised to perform?（）A、Reboot the system in normal mode.B、Use the bosboot command to rebuild the boot image.C、Restore the boot logical volume from a mksysb image.D、Reboot the system into maintenance mode and run fsck on the boot logical volume.
During reboot， the system hangs with an LED 0554 message that means， "The boot device could not be opened or a read failed." Which of the following recovery procedures should be taken （）A、Boot in maintenance mode and use fsck to check hd5.B、Boot in maintenance mode， access the rootvg and check the /etc/inittab for corruption.C、Boot in maintenance mode， access the rootvg and rebuild the boot image using the bosboot command.D、Boot in maintenance mode， and reset the root password.
多选题Which two locations can be configured as a source for the IOS image in the boot system command?（）ARAMBNVRAMCflash memoryDHTTP serverETFTP serverFTelnet server
多选题Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）ARouter1 has specific boot system command that instruct it to load IOS from TFTP server.BRouter1 is acting as a TFTP server for other routers.CRouter1 cannot locate a valid IOS image in flash memory.DRouter1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.ECisco routers will first attempt to load a image from TFTP for management purposes.
单选题What is the main reason for using the "ip ips deny-action ips-interface" IOS command？（）A To selectively apply drop actions to specific interfacesB To enable IOS to droptraffic for signatures configured with the Drop actionC To support load-balancing configurations in which traffic can arrive via multipleinterfaces D This is nota valid IOS command
单选题A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）AThere is an error in the router DRAM.BTe IOS image is corrupt.CThe configuration register is set to 0x2142.DThe TFTP server that contains the router configuration file is unreachable.EA boot system configuration command has placed the router into setup mode.
多选题Using the LIST command in Recovery Manager （RMAN）， which two pieces of information from the RMAN repository can be listed？ （）Abackups that can be deletedBstored scripts in the recovery catalogCbackup sets and image copies that are obsoleteDonly the most recent backup sets or image copiesEbackups that do not have the AVAILABLE status in RMAN repository
单选题Which result is of securing the Cisco IOS image by use of the Cisco IOS image resilience feature？（）AThe Cisco IOS image file will not be visible in the output from the show flash command.BThe show version command will not show the Cisco IOS image file location.CWhen the router boots up， the Cisco IOS image will be loaded from a secured FTP location.DThe running Cisco IOS image will be encrypted and then automatically backed up to a TFTP server.
单选题Which command do you use to display the messages seen during the last system boot?（）Ashow system boot-messagesBshow chassis messagesCshow file system boot-messagesDshow boot-log messages
多选题Using the LIST command in Recovery Manager （RMAN），which two pieces of information in the RMAN repository can be listed？（）Astored scripts in the recovery catalogBbackups that can be deleted from diskCbackup sets and image copies are obsoleteDbackups that do not have the AVAILABLE status in the RMAN repository
多选题User defined locale files can be stored in which two locations?（）ADRAMBSDRAMCCME flash，slot0DCUE flash，slot0ETFTP directory specified by cnf-file location command
多选题When resetting a Catalyst Express switch to factory default settings， which three options are available from the Software Recovery window？（）ABoot to a password recovery windowBBoot with the factory default imageCErase the system configuration and boot with the factory default IOS imageDErase the system configuration and boot from a TFTP-supplied IOS imageEErase the System Configuration