In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）A、Configure MSDP between RPs.B、Redistribute multicast information in your IGP.C、Advertise S, G entries using MBGP.D、Configure PIM to advertise group information between RPs.
In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）
- A、Configure MSDP between RPs.
- B、Redistribute multicast information in your IGP.
- C、Advertise S, G entries using MBGP.
- D、Configure PIM to advertise group information between RPs.
相关考题：
Which method should be used to dynamically elect an RP when your network is using PIM version1?() A. auto-RPB. static RPC. discovery modeD. bootstrap protocol
Which three RP election mechanisms are available in a PIM－SM domain?() A. StaticB. Auto-RPC. Dynamic-RPD. Bootstrap routerE. Anycast-RP
Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? () A. Configure a non-unique address on the loopback interface for use by the PIM RP.B. Configure MSDP with the unique address (router ID) as the local address of the peer.C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.D. Configure a unique address on the loopback interface, used as the PIM RP.
When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?() A. PIM - DMB. PIM - SMC. PIM - RPD. CGMPE. IGMP snooping
WhichtypeofdomainsisinterconnectedusingMulticastSourceDiscoveryProtocol?() A.PIM-SMB.PIM-DMC.PIM-SSMD.DVMRP
When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?（）A、PIM - DMB、PIM - SMC、PIM - RPD、CGMPE、IGMP snooping
Which type of domains is interconnected using Multicast Source Discovery Protocol？（）A、PIM-SMB、PIM-DMC、PIM-SSMD、DVMRP
Which three RP election mechanisms are available in a PIM-SM domain?（）A、StaticB、Auto-RPC、Dynamic-RPD、Bootstrap routerE、Anycast-RP
In what PIM topology would you use MSDP within a single domain？（）A、Auto-RPB、Anycast RPC、Bootstrap routerD、PIM sparse mode
Which are correct descriptions and configurations of Anycast RP？（）A、In Anycast RP， two or more RPs are configured with the same IP address on loopback interfaces.B、Anycast RP provides redundancy and load-sharing capabilities.C、Routers with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip pim rp-address 1.1.1.1D、Routers with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip rp-address pim 1.1.1.1E、Routers with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip anycast-rp pim 1.1.1.1
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicast traffic to a group？（）A、The source must send a PIM Register message to the rendezvous point （RP）B、The source must first join the multicast group using IGMP before sendingC、The source must perform a Request to Send （RTS） and Clear to Send （CTS） handshake with the PIM designated router （DR）D、No control plane signaling needs to be performed；the source can simply begin sending on the local subnet
In order to configure two routers as anycast RPs， which of these requirements， af a minimum， must besatisfied？（）A、Multicast Source Discovery Protocol mesh-groups must be configured between the two anycast RPs.B、The RPs must be within the same IGP domain.C、Multicast Source Discovery Protocol must be configured between the two anycast RPs.D、The two anycast RPs must be IBGP peers.
When IP multicast is enabled via PIM, which mode uses the flood and prune metho d? Select the best response.（）A、PIM sparse - denseB、Bidir - PIMC、PIM - RPD、PIM - DME、PIM - SM
Which three statements about anycast RP are true？ （）A、MSDP is running between anycast RPsB、Anycast RP provides redundancy and load-sharing capabilitiesC、Multicast BGP is running between anycast RPsD、In anycast RP，two or more RPs are configured with the same multicast IP address on loopback interfacesE、In anycast RP，two or more RPs are configured with the same unicast IP address on loopback interfaces
In order to configure two routers as anycast RPs，which of these requirements，at a minimum， must be satisfied？（）A、Multicast Source Discovery Protocol mesh-groups must be configured between the two anycast RPs.B、The RPs must be within the same IGP domain.C、Multicast Source Discovery Protocol must be configured between the two anycast RPs.D、The two anycast RPs must be IBGP peers.
What is the benefit of using Anycast RP via RFC 4610 for IP multicast RP redundancy？（） A、 Improves convergence of the multicast network due to enhanced RPF checksB、 Simplifies the number of control plane protocols over other RP redundancy methodsC、 Eliminates the use of Protocol Independent Multicast （PIM） in the topologyD、 Increases the administrative distances in Multicast Source Discovery Protocol （MSDP） configuration
单选题In order to configure two routers as anycast RPs， which of these requirements， af a minimum， must besatisfied？（）AMulticast Source Discovery Protocol mesh-groups must be configured between the two anycast RPs.BThe RPs must be within the same IGP domain.CMulticast Source Discovery Protocol must be configured between the two anycast RPs.DThe two anycast RPs must be IBGP peers.
多选题Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? （）AConfigure a non-unique address on the loopback interface for use by the PIM RP.BConfigure MSDP with the unique address (router ID) as the local address of the peer.CConfigure MSDP with the non-unique address (router ID) as the local address of the peer.DConfigure a unique address on the loopback interface, used as the PIM RP.
单选题What is the benefit of using Anycast RP via RFC 4610 for IP multicast RP redundancy？（）A Improves convergence of the multicast network due to enhanced RPF checksB Simplifies the number of control plane protocols over other RP redundancy methodsC Eliminates the use of Protocol Independent Multicast （PIM） in the topologyD Increases the administrative distances in Multicast Source Discovery Protocol （MSDP） configuration
多选题Which are correct descriptions and configurations of Anycast RP？（）AIn Anycast RP， two or more RPs are configured with the same IP address on loopback interfaces.BAnycast RP provides redundancy and load-sharing capabilities.CRouters with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip pim rp-address 1.1.1.1DRouters with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip rp-address pim 1.1.1.1ERouters with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip anycast-rp pim 1.1.1.1
单选题Which method should be used to dynamically elect an RP when your network is using PIM version1?（）Aauto-RPBstatic RPCdiscovery modeDbootstrap protocol
多选题In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）AConfigure MSDP between RPs.BRedistribute multicast information in your IGP.CAdvertise S, G entries using MBGP.DConfigure PIM to advertise group information between RPs.
多选题Which three statements about anycast RP are true？ （）AMSDP is running between anycast RPsBAnycast RP provides redundancy and load-sharing capabilitiesCMulticast BGP is running between anycast RPsDIn anycast RP，two or more RPs are configured with the same multicast IP address on loopback interfacesEIn anycast RP，two or more RPs are configured with the same unicast IP address on loopback interfaces
单选题When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?（）APIM - DMBPIM - SMCPIM - RPDCGMPEIGMP snooping
单选题In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicast traffic to a group？（）AThe source must send a PIM Register message to the rendezvous point （RP）BThe source must first join the multicast group using IGMP before sendingCThe source must perform a Request to Send （RTS） and Clear to Send （CTS） handshake with the PIM designated router （DR）DNo control plane signaling needs to be performed；the source can simply begin sending on the local subnet
单选题In what PIM topology would you use MSDP within a single domain？（）AAuto-RPBAnycast RPCBootstrap routerDPIM sparse mode
单选题What is the correct configuration of Anycast RP on the loopback interface， assuming a shared anycast address of 10.1.1.1？（）A AB BC CD D