In what PIM topology would you use MSDP within a single domain？（）A、Auto-RPB、Anycast RPC、Bootstrap routerD、PIM sparse mode
In what PIM topology would you use MSDP within a single domain？（）
- A、Auto-RP
- B、Anycast RP
- C、Bootstrap router
- D、PIM sparse mode
相关考题：
Which three RP election mechanisms are available in a PIM－SM domain?() A. StaticB. Auto-RPC. Dynamic-RPD. Bootstrap routerE. Anycast-RP
Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? () A. Configure a non-unique address on the loopback interface for use by the PIM RP.B. Configure MSDP with the unique address (router ID) as the local address of the peer.C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.D. Configure a unique address on the loopback interface, used as the PIM RP.
Refer to the network of Layer 3 switches in the exhibit. The RPI Multi cast Server only multicasts to hosts connected to multilayer switches 5 and 6. The CMU Multicast Server multicasts to hosts on multilayer switches 1 - 6. Given the number of configuration steps involved, what is the most efficient way to configure the net work while meeting the requirements for multicast data flow? （）A. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Specify switch 1 as the root for the RPI Multicast Server. Specify switch 2 as the root for the CMU Multicast Server.B. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode. Leave each multicast server as the root of its own multicast tree.C. Configure each switch with PIM sparse - dense mode. Configure switch 3 as a ren dezvous point for the RPI multicast stream.D. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Allow the switches to elect their own root for each multicast tree.E. Configure each switch with PIM sparse mode.F. Configure each switch with PIM dense mode.
Which three statements are true about IP multicast configuration?() A. PIM sparse - dense mode and PIM dense mode require an RP on the network.B. PIM sparse mode and PIM dense mode require an RP on the network.C. PIM sparse mode interfaces are always added to the multicast routing table in a router.D. PIM sparse mode and PIM sparse - dense mode require an RP on the network.E. PIM dense mode interfaces are always added to the multicast routing table in a router.F. PIM sparse - dense mode acts as PIM dense mode if an RP is not known.
What is the purpose of a rendezvous point (RP)?() A. acts as a meeting place for sources and receivers of multicast trafficB. used in PIM dense m ode to create a database of all multicast sourcesC. used in PIM dense and sparse mode to create a database of all multicast sourcesD. acts as the designated router for a broadcast segment when multicast routing is enabled
When IP multicast is enabled via PIM, which mode uses the flood and prune metho d? Select the best response.() A. PIM sparse - denseB. Bidir - PIMC. PIM - RPD. PIM - DME. PIM - SM
When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?() A. PIM - DMB. PIM - SMC. PIM - RPD. CGMPE. IGMP snooping
What is the purpose of IGMP in a multicast implementation?() A. it is not used in multicastB. it determines the virtual address group for a multicast destinationC. it dynamically registers individual hosts in a multicast group on a specific LAND. it is used on WAN connections to determine the maximum bandwidth of a connectionE. it determines whether Bidirectional PIM or PIM sparse mode will be used for a multicast flow
Choose two commands that are required to enable multicast on a router， when it is known that thereceivers use a specific functionality of IGMPv3.（）A、ip pim rp-addressB、ip pim ssmC、ip pim sparse-modeD、ip pim passive
When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?（）A、PIM - DMB、PIM - SMC、PIM - RPD、CGMPE、IGMP snooping
What is the purpose of IGMP in a multicast implementation？（）A、 it is not used in multicastB、 it determines the virtual address group for a multicast destinationC、 it dynamically registers individual hosts in a multicast group on a specific LAND、 it is used on WAN connections to determine the maximum bandwidth of a connectionE、 it determines whether Bidirectional PIM or PIM sparse mode will be used for a multicast flow
The ip pim autorp listener command is used to do which of these？（）A、enable a Cisco router to "passively" listen to Auto-RP packets without the router actively sending or forwarding any of the packetsB、allow Auto-RP packets in groups 224.0.1.39 and 224.0.1.40 to be flooded in dense mode out interfaces configured with the ip pim sparse-mode commandC、enable the use of Auto-RP on a routerD、configure the router as an Auto-RP mapping agent
Which method should be used to dynamically elect an RP when your network is using PIM version1?（）A、auto-RPB、static RPC、discovery modeD、bootstrap protocol
Which method of dynamic RP election is non-proprietary？（）A、Auto-RPB、Static RPC、Bootstrap ProtocolD、Pim Sparse-Dense mode
Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? （）A、Configure a non-unique address on the loopback interface for use by the PIM RP.B、Configure MSDP with the unique address (router ID) as the local address of the peer.C、Configure MSDP with the non-unique address (router ID) as the local address of the peer.D、Configure a unique address on the loopback interface, used as the PIM RP.
In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）A、Configure MSDP between RPs.B、Redistribute multicast information in your IGP.C、Advertise S, G entries using MBGP.D、Configure PIM to advertise group information between RPs.
Multicast is being deployed in the network， and only ip pim sparse-dense mode has been configured on all interfaces in the network to support a new video streaming application. No other multicast configuration was applied anywhere in the network. Since enabling multicast， the network monitoring tools show periodic spikes in link utilization throughout the network， even in areas where the video application is not being used. What could be a possible cause？（）A、PIM sparse mode is being used.B、PIM dense mode is being used.C、The BGP multicast address family has not been configured.D、IGMP version 3 is being used.E、IP PIM neighbor filters have not been applied.
What is the purpose of a rendezvous point (RP)?（）A、acts as a meeting place for sources and receivers of multicast trafficB、used in PIM dense m ode to create a database of all multicast sourcesC、used in PIM dense and sparse mode to create a database of all multicast sourcesD、acts as the designated router for a broadcast segment when multicast routing is enabled
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message （knowing that the MSDP router is also configured as an RP for the PIM domain）？（）A、Source-Active MessageB、PIM JoinC、PIM HelloD、MSDP Register
When IP multicast is enabled via PIM, which mode uses the flood and prune metho d? Select the best response.（）A、PIM sparse - denseB、Bidir - PIMC、PIM - RPD、PIM - DME、PIM - SM
What is the benefit of using Anycast RP via RFC 4610 for IP multicast RP redundancy？（） A、 Improves convergence of the multicast network due to enhanced RPF checksB、 Simplifies the number of control plane protocols over other RP redundancy methodsC、 Eliminates the use of Protocol Independent Multicast （PIM） in the topologyD、 Increases the administrative distances in Multicast Source Discovery Protocol （MSDP） configuration
Which three RP election mechanisms are available in a PIM-SM domain?（）A、StaticB、Auto-RPC、Dynamic-RPD、Bootstrap routerE、Anycast-RP
Which three RP election mechanisms are available in a PIM-SM domain？（）A、StaticB、Auto-RPC、Dynamic-RPD、Bootstrap router
单选题Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message （knowing that the MSDP router is also configured as an RP for the PIM domain）？（）ASource-Active MessageBPIM JoinCPIM HelloDMSDP Register
单选题In what PIM topology would you use MSDP within a single domain？（）AAuto-RPBAnycast RPCBootstrap routerDPIM sparse mode
多选题Which three statements are true about IP multicast configuration?（）APIM sparse - dense mode and PIM dense mode require an RP on the network.BPIM sparse mode and PIM dense mode require an RP on the network.CPIM sparse mode interfaces are always added to the multicast routing table in a router.DPIM sparse mode and PIM sparse - dense mode require an RP on the network.EPIM dense mode interfaces are always added to the multicast routing table in a router.FPIM sparse - dense mode acts as PIM dense mode if an RP is not known.
单选题What is the benefit of using Anycast RP via RFC 4610 for IP multicast RP redundancy？（）A Improves convergence of the multicast network due to enhanced RPF checksB Simplifies the number of control plane protocols over other RP redundancy methodsC Eliminates the use of Protocol Independent Multicast （PIM） in the topologyD Increases the administrative distances in Multicast Source Discovery Protocol （MSDP） configuration