Which command is a valid way to view the status of an interface?（）A、show interfaces fe-0/0/0 extensiveB、show interfaces fe-0/0/0 statusC、show interfaces fe-0/0/0 health-infoD、show interfaces fe-0/0/0 verbose
Which command is a valid way to view the status of an interface?（）
- A、>show interfaces fe-0/0/0 extensive
- B、>show interfaces fe-0/0/0 status
- C、>show interfaces fe-0/0/0 health-info
- D、>show interfaces fe-0/0/0 verbose
相关考题：
An administrator is unable to ping any address on the 10.0.19.0/24 subnet. To identify the problem, the administrator uses the command shown in the exhibit.Which step should be taken to solve the problem?（）A. Check the physical cable.B. Issue the command activate interfaces fe-0/0/1.5 .C. Issue the command delete interfaces fe-0/0/1.5 disable.D. Reconfigure the IP address.
A network administrator wants to verify the active alarms on interface so－0／0／0.0. Which command displays this information?() A. show interfaces alarmsB. show interfaces terseC. show alarms extensiveD. show interfaces extensive
A network administrator would like to view detailed interface status, properties, statistics, errors,and CoS packet counters.Which operational command will display this information?() A. show interfaces extensiveB. show interfacesC. show configuration interfacesD. show interface status
How do you enable interface fe－0／0／0 under the [edit protocols isis] level to form both a Level 1 and Level 2 adjacency?() A. set interface fe-0/0/0.0B. set interface fe-0/0/0.0 all levelC. set interface fe-0/0/0.0 level 3 enableD. set interface fe-0/0/0.0 level 1 level 2
Which command sequence displays queue statistics for an interface?() A.monitor interface ge-0/0/0 queueB.show interfaces queue ge-0/0/0C.show interfaces ge-0/0/0 statistics extensiveD.show statistics queue detail
Which command sequence shows traffic per queue for an interface?() A.show interfaces queue ge-0/0/0B.show statistics queue detailC.show interfaces ge-0/0/0 statistics extensiveD.monitor interface ge-0/0/0 queue
Which command would you type to see a concise display of which interfaces are up and which are down?() A.show interfaces briefB.show interfaces statusC.show ip interface briefD.show interfaces terse
A network administrator wants to verify the active alarms on interface so－0／0／0. Which command displays this information?() A. show interfaces alarmsB. show interfaces terseC. show alarms extensiveD. show interfaces extensive
Which two are correct when configuring an IP address for a Fast Ethernet interface?() A.set interfaces fe-0/0/0 address 10.1.1.1/24B.set interfaces fe-0/0/0.0 family inet address 10.1.1.1/24C.set interfaces fe-0/0/0.0 address 10.1.1.1/24D.set interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24
Which option is correct to configure the maximum transmit packet size of a Fast Ethernet interface?() A.set interfaces fe-0/0/0 unit 0 ethernet-options mtu 1200B.set interfaces fe-0/0/0 mtu 1200C.set interfaces fe-0/0/0 unit 0 mtu 1200D.set interfaces fe-0/0/0.0 mtu 1200
Which command can be used to determine the type of cable attached to the Serial 0／0 interface on a router?() A. show interfaces serial 0/0B. show running-configC. show versionD. show controllers serial 0/0E. show ip interfaceF. show line serial 0/0
Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?（）A.Telnet to WANRouter and execute the command show interfaces S0/0B.Telnet to WANRouter and execute the commandshow processes S0/0C.Telnet to WANRouter and execute the command show running-configurationD.Telnet to WANRouter and execute the command show controller S0/0E.Physically examine the cable between WANRouter S0/0 and the DCE.F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0
The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner（）。A.Telnet to WANRouter and execute the command show interfaces S0/0B.Telnet to WANRouter and execute the command show processes S0/0C.Telnet to WANRouter and execute the command show running-configurationD.Telnet to WANRouter and execute the command show controller S0/0E.Physically examine the cable between WANRouter S0/0 and the DCEF.Establish a console session on WANRouter and execute the command show interfaces S0/0
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）A、show interfaces serial 0/0B、show running-configC、show versionD、show controllers serial 0/0E、show ip interfaceF、show line serial 0/0
A network administrator wants to verify the active alarms on interface so-0/0/0.0. Which command displays this information?（）A、show interfaces alarmsB、show interfaces terseC、show alarms extensiveD、show interfaces extensive
Which command sequence shows traffic per queue for an interface?（）A、show interfaces queue ge-0/0/0B、show statistics queue detailC、show interfaces ge-0/0/0 statistics extensiveD、monitor interface ge-0/0/0 queue
A network administrator wants to verify the active alarms on interface so-0/0/0. Which command displays this information?（）A、show interfaces alarmsB、show interfaces terseC、show alarms extensiveD、show interfaces extensive
A network administrator would like to view detailed interface status, properties, statistics, errors,and CoS packet counters.Which operational command will display this information?（）A、show interfaces extensiveB、show interfacesC、show configuration interfacesD、show interface status
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A、The show ip eigrp neighbors command on R1 lists the revised Hello timerB、The show ip eigrp interfaces command on R1 lists the revised Hello timerC、The R1 - R2 neighborship fails due to Hello timer mismatcHD、The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner（）。A、Telnet to WANRouter and execute the command show interfaces S0/0B、Telnet to WANRouter and execute the command show processes S0/0C、Telnet to WANRouter and execute the command show running-configurationD、Telnet to WANRouter and execute the command show controller S0/0E、Physically examine the cable between WANRouter S0/0 and the DCEF、Establish a console session on WANRouter and execute the command show interfaces S0/0
Which command sequence displays queue statistics for an interface?（）A、monitor interface ge-0/0/0 queueB、show interfaces queue ge-0/0/0C、show interfaces ge-0/0/0 statistics extensiveD、show statistics queue detail
What is shown by the command show interfaces extensive fe-0/0/0 but not shown by the command show interface detail fe-0/0/0？（）A、input error counterB、interface MTU sizeC、input packets counterD、the IP address on logical interface fe-0/0/0.0
You are configuring new BGP neighbor and want to view the configuration for the interface ge-0/0/0.42.Which command do you use to achieve this result?（）A、[edit protocols bgp group external] user@router# set interfaces ge-0/0/0.42 ?B、[edit protocols bgp group external] user@router# edit show interfaces ge-0/0/0.42C、[edit protocols bgp group external] user@router# top show interfaces ge-0/0/0.42D、[edit protocols bgp group external] user@router# show interfaces ge0/0/0.42
How do you enable interface fe-0/0/0 under the [edit protocols isis] level to form both a Level 1 and Level 2 adjacency?（）A、set interface fe-0/0/0.0B、set interface fe-0/0/0.0 all levelC、set interface fe-0/0/0.0 level 3 enableD、set interface fe-0/0/0.0 level 1 level 2
Which command would you type to see a concise display of which interfaces are up and which are down?（）A、show interfaces briefB、show interfaces statusC、show ip interface briefD、show interfaces terse
单选题What is shown by the command show interfaces extensive fe-0/0/0 but not shown by the command show interface detail fe-0/0/0？（）Ainput error counterBinterface MTU sizeCinput packets counterDthe IP address on logical interface fe-0/0/0.0
单选题Which command is a valid way to view the status of an interface？（）Ashow interfaces fe-0/0/0 extensiveBshow interfaces fe-0/0/0 statusCshow interfaces fe-0/0/0 health-infoDshow interfaces fe-0/0/0 verbose