On which component are RED and WRED managed in the router?（）A、I/O moduleB、switch fabricC、egress line moduleD、ingress line module
On which component are RED and WRED managed in the router?（）
- A、I/O module
- B、switch fabric
- C、egress line module
- D、ingress line module
相关考题：
On which component are RED and WRED managed in the router?() A. I/O moduleB. switch fabricC. egress line moduleD. ingress line module
Which statement describes queue and buffer managment in the E－series router?() A. Buffer memory is managed dynamically in the I/O module.B. Buffer memory is managed dynamically in the switch fabric.C. Buffer memory is managed dynamically on egress line modules.D. Buffer memory is managed dynamically on ingress line modules
What is the term "ordered control" mean regarding how MPLS LSPs are established?() A. establish starting at the egress router going back to the ingress routerB. establish starting at the ingress router going downstream to the egress routerC. establish when a router learns of a new prefixD. establish when the path correctly matches the reverse path forwarding check
Which ERX Edge Router component is responsible for all packet processing and packet forwarding?() A.I/O adapterB.line moduleC.shared memory fabricD.switch route processor
Where does Layer2 de－encapsulation occur on the ERX Edge Router?() A.on the SRPB.on the I/O adapterC.on the egress line moduleD.on the ingress line module
What are two way sthat IP datagrams are passed from the ingress line module to the egress line module?() A.over an ATM PVCB.over a FastEthernet busC.overa Gigabit Ethernet busD.over high speed serial bus
The router SIS-R has been configured in a CIS network. As a network administrator, you were required to enable MPLS on that router.Which of the following description is making sense on the basis of the output information?（）A. CEF switching is only needed to forward labeled packets.B. CEF switching is needed on both ingress and egress interfaces on which MPLS is enabled.C. Interface-level CEF switching is needed only on egress interfaces that are sending IP packets on which the egress LSR performs the label imposition process.D. Interface-level CEF switching is needed only on ingress interfaces that are receiving IP packets on which the ingress LSR performs the label imposition process.
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）A. Switch1(config)# i nterface fa0 /1 Switch1(config-if)# ip address 192.168.24.3.255.255.255.0B. Switch1 (config)#interface fa0/1 Switch1 (config-if)# switchport mode trunkC. Switch 1 (config)# i nterface fa0 /1 Switch1 (config-if)# duplex full Switch1 (config-if)# speed 100D. Switch1 (config-if)# default-gateway 192.168.24.1E. Switch1 (config)# line con 0 Switch1(config-line)# password cisco Switch1 (config-line)#login
On Cisco Nexus 5000 Series Switches， where are the virtual output queues implemented， and what is the main purpose of virtual output queues？（）A、 on all ingress interfaces； to ensure maximum throughput on a per-egress， per-CoS basisB、 on all ingress interfaces； to provide independent congestion management and 16 queuesC、 on all egress interfaces； so that a congested egress port does not affect traffic directed to other egress portsD、 on all egress interfaces； to prevent head-of-line blocking by utilizing multiple virtual output queuesE、 on all egress interfaces； to be able to use EEE 802.1p CoS
What is the importance of using Virtual Output Queues on ingress Line Cards in a high-end router？（）A、Prevents head-of-line blockingB、Uses less memoryC、Increases forwarding performanceD、Simplifies configuration
Which ERX Edge Router component is responsible for all packet processing and packet forwarding？（）A、I/O adapterB、line moduleC、shared memory fabricD、switch route processor
Which statement describes queue and buffer managment in the E-series router?（）A、Buffer memory is managed dynamically in the I/O module.B、Buffer memory is managed dynamically in the switch fabric.C、Buffer memory is managed dynamically on egress line modules.D、Buffer memory is managed dynamically on ingress line modules
What are two way sthat IP datagrams are passed from the ingress line module to the egress line module?（）A、over an ATM PVCB、over a FastEthernet busC、overa Gigabit Ethernet busD、over high speed serial bus
Where does Layer2 de-encapsulation occur on the ERX Edge Router？（）A、on the SRPB、on the I/O adapterC、on the egress line moduleD、on the ingress line module
ZXG10-BTS（V2）的AEM是指（）。A、Amplifier Equipment ModuleB、Antenna Equipment ModuleC、Amplifier Enhanced ModuleD、Antenna Enhanced Module
Which component of the Cisco nexus 1000v monitors the migration of virtual machine during vmotion events?（）A、UCS MangerB、virtual supervisor moduleC、virtual ethernet moduleD、distributed virtual switch
Which command is required to apply an access list on a virtual terminal line of a router?（）A、Router(config-line)# access-class 10 inB、Router(config-if)# ip access-class 23 outC、Router(config-line)# access-group 15 outD、Router(config-if)# ip access-group 110 inE、Router(config-line)# access-list 150 inF、Router(config-if)# ip access-list 128 out
The Cisco 6100 XP Fabric Interconnect is available in Which two configurations?（）A、20 port+expansion moduleB、24 port+expansion moduleC、40 port+expansion moduleD、48 port+expansion module
What is the term "ordered control" mean regarding how MPLS LSPs are established?（）A、establish starting at the egress router going back to the ingress routerB、establish starting at the ingress router going downstream to the egress routerC、establish when a router learns of a new prefixD、establish when the path correctly matches the reverse path forwarding check
The primary line module has failed and the spare line module is nowactive.What occurs，by default，when the primary line module returns to an operational status？（）A、The primary line module is inactive for five minutes and then becomes active.B、The primary line module is in standby mode，while the spare line module remains active.C、The primary line module becomes active immediately and the spare line module becomes inactive.D、The primary and spare line modules are active for five minutes，after which time the spare line module becomes inactive.
A banking customer deployed an IBM BladeCenter chassis with one Brocade 8Gb SAN switch module. The customer requires an 8Gb uplink or higher. Which configuration will meet this request of the following？（）A、Brocade Enterprise 20-port 8Gb SAN switch moduleB、Brocade 20-port8Gb SAN switch module and Brocade Advanced Performance Monitoring for IBM BladeCenterC、Brocade Enterprise 10-port 8Gb SAN switch moduleD、Brocade 10-port8Gb SAN switch module and Brocade Advanced Performance Monitoring for IBM BladeCenter
单选题The primary line module has failed and the spare line module is nowactive.What occurs，by default，when the primary line module returns to an operational status？（）AThe primary line module is inactive for five minutes and then becomes active.BThe primary line module is in standby mode，while the spare line module remains active.CThe primary line module becomes active immediately and the spare line module becomes inactive.DThe primary and spare line modules are active for five minutes，after which time the spare line module becomes inactive.
多选题The Cisco 6100 XP Fabric Interconnect is available in Which two configurations?（）A20 port+expansion moduleB24 port+expansion moduleC40 port+expansion moduleD48 port+expansion module
单选题Where does Layer2 de-encapsulation occur on the ERX Edge Router？（）Aon the SRPBon the I/O adapterCon the egress line moduleDon the ingress line module
单选题On which component are RED and WRED managed in the router?（）AI/O moduleBswitch fabricCegress line moduleDingress line module
单选题On Cisco Nexus 5000 Series Switches， where are the virtual output queues implemented， and what is the main purpose of virtual output queues？（）A on all ingress interfaces； to ensure maximum throughput on a per-egress， per-CoS basisB on all ingress interfaces； to provide independent congestion management and 16 queuesC on all egress interfaces； so that a congested egress port does not affect traffic directed to other egress portsD on all egress interfaces； to prevent head-of-line blocking by utilizing multiple virtual output queuesE on all egress interfaces； to be able to use EEE 802.1p CoS