A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）A、The next hop is I2's BGP RIDB、The next hop is I2's IP address used on the R2 - I2 neigh bor relationshipC、The next hop is R2's BGP RIDD、The next hop is R2's IP address used on the R1 - R2 neighbor relationship
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）
- A、The next hop is I2's BGP RID
- B、The next hop is I2's IP address used on the R2 - I2 neigh bor relationship
- C、The next hop is R2's BGP RID
- D、The next hop is R2's IP address used on the R1 - R2 neighbor relationship
相关考题：
Router R1 has eBGP connections to I1 and I 2, routers at the same ISP. The company that owns R1 can use public address range 130.1.16.0/20. The following output lists all the IP routes in R1‘s routing table within this rangE. Which of the following answers would cause R1 to advertise the 130.1.1 6.0/20 prefix to its eBGP peers?（）R1 show ip route 130.1.16.0 255.255.240.0 longer - prefixes! lines omitteD...O 130.1.16.0/24 [110/3] via 10.5.1.1, 00:14:36, FastE thernet0/1O 130.1.17.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1O 130.1.18.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1A. Configure R1 with the network 130.1.16.0 mask 255.255.240.0 command.B. Configure R1 with the network 130.1.16 .0 mask 255.255.240.0 summaryonly command.C. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed.D. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed, and create a BGP summary for 130.1.16.0/20.
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A. 22B. 11C. 1D. None
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Refer to the e xhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover?（）A. Configure BGP n eighbor relationships between all interfaces on R1 and R4.B. Install a direct connection between R1 and R4.C. Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.D. Configure only one neighbor relationship between R1‘s 192.168.1.2 interface and R4‘s 172.16.10.2 interface.
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）A. The redistribution command should be reentered with the match route - type parameter included.B. The redistribution command should be reentered wit h the route - map map - tag parameter included.C. The redistribution command should be reentered with the metric metric - value parameter included.D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command.Which of the following is true as a result?() A.R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1B.R1 can send IP packets to R2, but R2 cannot send IP packets to R1C.R2 no longer learns EIGRP routes from R1 for routes not connected to R1D.R1 no longer replies to R2‘s Query messagesE.R2n o longer sends to R1 Query messages
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）A. The OSPF area is not configured properly.B. The priority on R1 should be set higher.C. The cost on R1 should be set higher.D. The hello and dead timers are not configured properly.E. A backup designated router needs to be added to the network.F. The OSPF process ID numbers must match.
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192／26 network to a host on the LAN attached to router R1?() A.The path of the packets will be R3 to R2 to R1.B.The path of the packets will be R3 to R1 to R2.C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.D.The path of the packets will be R3 to R1
A network administrator is troubleshooting the OSPF configuration of routers R1 an dR2.The routers cannote stablish an adjacency relation ship on their common Ethernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 an dR2.Based on the information in the graphic，what is the cause of this problem？（）A.The OSPF area is not configured properly.B.The priority on R1 should be set higher.C.The cost on R1 should be set higher.D.The hello and dead timers are not configured properly.E.A backup designated router needs to be added to the network.F.The OSPF process ID numbers must match.
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）A、R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1B、R1 can send IP packets to R2, but R2 cannot send IP packets to R1C、R2 no longer learns EIGRP routes from R1 for routes not connected to R1D、R1 no longer replies to R2's Query messagesE、R2n o longer sends to R1 Query messages
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）A、Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.B、R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.C、R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.D、All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）A、frame - relay map commands on R3 - R10 referencing the other routers in this groupB、Nine OSPF neighbor commands on each routerC、Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10D、R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRE、R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A、The show ip eigrp neighbors command on R1 lists the revised Hello timerB、The show ip eigrp interfaces command on R1 lists the revised Hello timerC、The R1 - R2 neighborship fails due to Hello timer mismatcHD、The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）A、 LearnB、 SpeakC、 StandbyD、 ListenE、 ActiveF、 Remove
多选题Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?（）AAll of the routers need to be configured for backbone Area 1.BR1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.CA static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.DThe hello and dead interval timers are not set to the same values on R1 and R3.EEIGRP is also configured on these routers with a lower administrative distance.FR1 and R3 are configured in different areas.
单选题Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A22B11C1DNone
多选题Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）Arouter bgp 2Brouter bgp 1Cneighbor 10.1 .1.2 remote - as 2Dneighbor 10.1.1.2 Update - source 10.1.1.1Eneighbor 10.1.1.2 Update- source S0/0
单选题Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）ATraffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.BR2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.CR2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.DAll the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
多选题Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）Aframe - relay map commands on R3 - R10 referencing the other routers in this groupBNine OSPF neighbor commands on each routerCNine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10DR1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRER3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
单选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）AThe next hop is I2's BGP RIDBThe next hop is I2's IP address used on the R2 - I2 neigh bor relationshipCThe next hop is R2's BGP RIDDThe next hop is R2's IP address used on the R1 - R2 neighbor relationship
多选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers. Which of the following could be used to prevent potential routing loops in this design?（）AUsing an iBGP mesh inside the Enterprise coreBConfiguring default routes in the Enterprise pointing to both R1 and R2CRedistributing BGP routes into the Enterprise IGPDTunneling the packets for the i BGP connection between R1 and R2
多选题R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）ALearnBSpeakCStandbyDListenEActiveFRemove
单选题Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）AThe show ip eigrp neighbors command on R1 lists the revised Hello timerBThe show ip eigrp interfaces command on R1 lists the revised Hello timerCThe R1 - R2 neighborship fails due to Hello timer mismatcHDThe show ip eigrp interfaces detail command on R1 lists the revised Hello timer