After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）A、B、#C、?D、*E、All of the aboveF、None of the above
After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）
- A、>
- B、#
- C、?
- D、*
- E、All of the above
- F、None of the above
相关考题：
After working all night and successfully configuring a Cisco router for the Ezonexam network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode! Which of the choices below indicates the source of your problem?A．Hardware failure in NVRAM prevents the router from loading the configB．Startup-config in flash is corrupt and cannot be analyzedC．Router configuration-register set to bypass startup configurationD．Startup-config in NVRAM is corrupt and cannot be analyzedE．None of the above
You are working on an existing Web site. You need to secure the Web site by redirecting all users to the logon page, Login.aspx. After logging on, users must be sent back to the page that they originally requested.Which code segment should you use?（）A.B.C.D.
You want to log into the router and make a configuration change.After loggin in as the root user, what is the next command you must enter?() A. enableB. configureC. editD. cli
After logging into a router and typing in a few show commands, you press the up arrow key. What will this do?A．It will recall the previous command lineB．It will move the cursor one line upC．It will redisplay the current command lineD．It will capitalize the command lineE．None of the above
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What information can you determine about this network?() A. The network is stableB. There is a flapping link or interface, and router C knows an alternate path to the networkC. There is a flapping link or interf ace, and router C does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? () A. The network has been stable for at least the last 45 minutesB. There is a flapping link or interf ace, and router C knows an alternate path to the networkC. There is a flapping link or interface, and router A does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
After attempting to telnet into a router, you are denied and you receive the error message "password required, but none set." What configuration changes will allow telnet access into this router?() A.B.C.D.
After logging into the RtrB router, you issue the show interface command as displayed below:After considering the effects of the command output illustrated in the exhibit above,which of the following protocols are operational on the serial link?（）A. PPPB. IPC. CompressionD. IPXE. MultilinkF. ATX
After making changes to the router, you issue the copy running-config startup-config command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?（）A. The NVRAM is corrupted.B. The boot system commands were omitted in the configuration.C. The configuration register setting is incorrect.D. The upgraded configuration incompatible with the hardware platform.E. The upgraded IOS incompatible with the hardware.
After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?() A. B. #C. ?D. *E. All of the aboveF. None of the above
After logging into a router and typing in a few show commands, you press the up arrow key. What will this do?（）A、It will recall the previous command lineB、It will move the cursor one line upC、It will redisplay the current command lineD、It will capitalize the command lineE、None of the above
Which statement is true regarding syslog on Junos devices?（）A、No logging is enabled by default.B、By default, the information is stored in a file named events.C、Only the message severity level must be configured.D、You can configure the router to send log messages to the console.
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A、The AS is not correctly configuredB、The network subnet mask is incorrectly configuredC、The network wildcard mask is configured incorrectlyD、The network number is not correctly configuredE、The process id is configured incorrectlyF、None of the above
You would like to log messages up to the severity level "notification". Which three of these commands will you need to issue in order to enable syslog messages to be sent to the syslog server at the IP address 10.1.5.5? （）(Choose three.)A、logging onB、logging host 10.1.5.5C、logging console notificationsD、logging trap notifications
After working all night and successfully configuring a Cisco router for the TestKing network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode! Which of the choices below indicates the source of your problem?（）A、Hardware failure in NVRAM prevents the router from loading the configB、Startup-config in flash is corrupt and cannot be analyzedC、Router configuration-register set to bypass startup configurationD、Startup-config in NVRAM is corrupt and cannot be analyzedE、None of the above
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）A、The NVRAM is corrupted.B、The boot system commands were omitted in the configuration.C、The configuration register setting is incorrect.D、The upgraded configuration incompatible with the hardware platform.E、The upgraded IOS incompatible with the hardware.
You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall commandB、The count parameter allows the router to count the number of pings for logging purposesC、The count parameter allows the router to pause for 10000 seconds before sending out a pingD、The count parameter allows the router to send out 1000 pings and then stop
As there are several logging modes, which mode will a CIS router use when it stores log messages in Random Access Memory?（）A、syslog loggingB、console loggingC、buffered loggingD、terminal logging
Which statement is true regarding syslog on Junos devices?（）A、No logging is enabled by defaultB、By default the information is stored in all file named eventsC、Only the message severity level must be configuredD、You can configure the router to send log messages to the console
You are creating a job class. You want access to the detailed information for all the runs of each job in the class and every operation performed on every job in the class. Which setting will you use for the LOGGING_LEVEL parameter？（）A、 LOGGING_OFFB、 LOGGING_RUNSC、 LOGGING_FULLD、 LOGGING_NULL
单选题After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）AB#C?D*EAll of the aboveFNone of the above
单选题After logging into a router and typing in a few show commands, you press the up arrow key. What will this do?（）AIt will recall the previous command lineBIt will move the cursor one line upCIt will redisplay the current command lineDIt will capitalize the command lineENone of the above
单选题You want to log in to the router and make a configuration change. After logging in as the root user, what is the next command you must enter?（）AenableBconfigureCeditDcli
单选题You want to log into the router and make a configuration change.After loggin in as the root user, what is the next command you must enter?（）AenableBconfigureCeditDcli
单选题You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）AThe count parameter creates a counter that you can view with the show firewall command.BThe count parameter allows the router to count the number of pings for logging purposes.CThe count parameter allows the router to pause for 1000 seconds before sending out a ping.DThe count parameter allows the router to send out 1000 pings and then stop.
单选题You are creating a job class. You want access to the detailed information for all the runs of each job in the class and every operation performed on every job in the class. Which setting will you use for the LOGGING_LEVEL parameter？（）A LOGGING_OFFB LOGGING_RUNSC LOGGING_FULLD LOGGING_NULL
单选题You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）AThe count parameter creates a counter that you can view with the show firewall commandBThe count parameter allows the router to count the number of pings for logging purposesCThe count parameter allows the router to pause for 10000 seconds before sending out a pingDThe count parameter allows the router to send out 1000 pings and then stop