Does EIGRP support areas？
Does EIGRP support areas？
相关考题：
Which protocols does Cisco NSF support? () A. IS-IS, EIGRP, SSO, BGPB. ISSU, OSPF, IS-ISC. IETF, OSPF, ISSUD. EIGRP, BGP, OSPF, IS-IS
Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）A. 172.17.0.0/30B. 172.17.1.0/24C. 172.17.2.0/24D. 172.17.3 .0/25E. 172.17.3.128/25F. 172.17.10.0/24
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What information can you determine about this network?() A. The network is stableB. There is a flapping link or interface, and router C knows an alternate path to the networkC. There is a flapping link or interf ace, and router C does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? () A. The network has been stable for at least the last 45 minutesB. There is a flapping link or interf ace, and router C knows an alternate path to the networkC. There is a flapping link or interface, and router A does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Why does RouterA show multiple unequal cost paths to network 192.168.81.0／24()。 A.A variance was configured for EIGRP autonomous system 109.B.The EIGRP topology table displays all routes to a destination.C.The EIGRP topology table shows only backup routes to a destination.D.Multiple floating static routes were configured to network 192.168.81.0 via interface Serial0.
Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）A、R1 limi ts EIGRP to around 250Kbps on DLCI 102B、R1 limits EIGRP to around 250Kbps on DLCI 104C、R1 limits EIGRP to around 150Kbps on every DLCID、R1 does not limit EIGRP because noWAN bandwidth control has been configured
Why does RouterA show multiple unequal cost paths to network 192.168.81.0/24（）。A、A variance was configured for EIGRP autonomous system 109.B、The EIGRP topology table displays all routes to a destination.C、The EIGRP topology table shows only backup routes to a destination.D、Multiple floating static routes were configured to network 192.168.81.0 via interface Serial0.
Which of the following is true regarding the effect of EIGRP queries on the network design？（）A、 EIGRP queries will be the most significant issue with respect to stability and convergence B、 EIGRP queries are not a consideration as long as EIGRP has a feasible successor with a nexthop AD that is greater than the FD of the current successor route C、 EIGRP queries will only increase the convergence time when there are no EIGRP stubsdesigned in the network
You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.D、There is no network statement configuration in EIGRP for IPv6.E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive
Which of the following is a disadvantage of using the EIGRP protocol?（）A、It does not scale wellB、It converges slower than OSPFC、It is a proprietary protocolD、It is a distance vector protocol
Which command will display all the EIGRP feasible successor routes known to a router?（）A、Router# show ip eigrp routes *B、Router# show ip eigrp summaryC、Router# show ip eigrp topologyD、Router# show ip eigrp adjacenciesE、Router# show ip eigrp neighbors detail
Which protocols does Cisco NSF support? （）A、IS-IS, EIGRP, SSO, BGPB、ISSU, OSPF, IS-ISC、IETF, OSPF, ISSUD、EIGRP, BGP, OSPF, IS-IS
Which EIGRP feature should a designer consider to limit the scope of EIGRP queries andminimize convergence time？（）A、 Using multiple EIGRP processesB、 Tuning down the EIGRP delay parameterC、 FIGRP stub routingD、 Limiting the number of EIGRP neighbor per device
A router has EIGRP configured as the only routing protocol. How does EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?（）A、It immediately sends its entire routing table to its neighbors.B、EIGRP sends a Hello packet to the DR to inform it of the route failure.C、It automatically forwards traffic to a fallback default route until a successor route is found.D、It sends queries out to neighbors until a new successor route is found.E、It places the route in holddown until LSA updates inform it of a new route to the network.
Which of the following commands shows all routes learned via EIGRP？（Choose all that apply.）（）A、show ip eigrp topologyB、show ip eigrp adjacencyC、show ip eigrp routesD、show ip eigrp databaseE、show ip route eigrpF、show ip eigrp forwarding
Which of the following are not BGRP data structures？ （Choose all that apply.）（）A、EIGRP database tableB、EIGRP CEF tableC、EIGRP neighbor tableD、EIGRP adjacency tableE、EIGRP interface tableF、EIGRP topology table
Which three statements about EIGRP are true?（）A、EIGRP converges fast RIP because of DUAL and backup routes that are stored in the topology table.B、EIGRP uses a hello protocol to establish neighbor relationshipsC、EIGRP uses split horizon and reverse poisoning to avoid routing loops.D、EIGRP uses periodic updates to exchange routing informationE、EIGRP allows routers of different manufacturers to interoperateF、EIGRP supports VLSM and authentication for routing updates.G、EIGRP use a broadcast address to send routing information.
单选题Why does RouterA show multiple unequal cost paths to network 192.168.81.0/24（）。AA variance was configured for EIGRP autonomous system 109.BThe EIGRP topology table displays all routes to a destination.CThe EIGRP topology table shows only backup routes to a destination.DMultiple floating static routes were configured to network 192.168.81.0 via interface Serial0.
单选题Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）AR1 limi ts EIGRP to around 250Kbps on DLCI 102BR1 limits EIGRP to around 250Kbps on DLCI 104CR1 limits EIGRP to around 150Kbps on every DLCIDR1 does not limit EIGRP because noWAN bandwidth control has been configured
单选题Which of the following commands shows all routes learned via EIGRP？（Choose all that apply.）（）Ashow ip eigrp topologyBshow ip eigrp adjacencyCshow ip eigrp routesDshow ip eigrp databaseEshow ip route eigrpFshow ip eigrp forwarding
单选题Which command will display all the EIGRP feasible successor routes known to a router?（）ARouter# show ip eigrp routes *BRouter# show ip eigrp summaryCRouter# show ip eigrp topologyDRouter# show ip eigrp adjacenciesERouter# show ip eigrp neighbors detail
单选题Which of the following is a disadvantage of using the EIGRP protocol?（）AIt does not scale wellBIt converges slower than OSPFCIt is a proprietary protocolDIt is a distance vector protocol
单选题Which EIGRP feature should a designer consider to limit the scope of EIGRP queries andminimize convergence time？（）A Using multiple EIGRP processesB Tuning down the EIGRP delay parameterC FIGRP stub routingD Limiting the number of EIGRP neighbor per device
多选题You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）AEIGRP for IPv6 is directly configured on the interfaces over which it runs.BEIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.CThere is a network statement configuration in EIGRP for IPv6， the same as for IPv4.DThere is no network statement configuration in EIGRP for IPv6.EWhen a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.FWhen a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive