What must be configured prior to the first commit after factory defaults are loaded?（）A、root authenticationB、default gatewayC、host nameD、management services
What must be configured prior to the first commit after factory defaults are loaded?（）
- A、root authentication
- B、default gateway
- C、host name
- D、management services
相关考题：
What is true about a Bypass Tunnel in MPLS Fast Reroute?() A. Only configured on the egress routerB. Only configured on the ingress routerC. Is pre-signalled to reduce packet lossD. Must intersect the primary LSP at two locations
Which three options are prerequisites to configuring Cisco AutoOoS？（）A、Cisco Express Forwarding （CEF） must be globally enabled.B、Prior to the enabling of the Cisco AutoOoS feature， the bandwidth command must be applied on all interfaces or subinterfaces.C、After the enabling of the Cisco AutoOoS feature， the bandwidth command must be applied on all interfaces or subinterfaces .D、OoS policies must be enabled on all interfaces that will participate in the AutoOoS configuration.E、An IP address must be configured on all low-bandwidth interfaces （768 kb/s or lower） that will participate in the AutoOoS configurationF、An IP address must be configured on all interfaces that will participate in the AutoOoS configuration
When configuring the Cisco VPN Client，what action is required prior to installing Mutual Group Authentication？（）A、Transparent tunneling must be enabled.B、A valid root certificate must be installed.C、A group pre-shared secret must be properly configured.D、The option to "Allow Local LAN Access" must be selected.
What is true about a Bypass Tunnel in MPLS Fast Reroute?（）A、Only configured on the egress routerB、Only configured on the ingress routerC、Is pre-signalled to reduce packet lossD、Must intersect the primary LSP at two locations
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A、The switch that will share its VLAN configuration must be in VTP server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be connected over VLAN trunks.E、The switches must be configured to use the same STP version.F、The switches must have VTP pruning activated.
What is a limitation of implementing uRPF？（）A、MPLS LDP must be enabled.B、BGP routing protocol must be running.C、Named access-lists must be configured.D、Symmetrical routing is required.E、Domain name must be defined
Prior to 802.1w，Cisco implemented a number of proprietary enhancements to 802.1D to improve convergence in a Layer 2 network. Which statement is correct？（）A、Only UplinkFast and BackboneFast are specified in 802.1w；PortFast must be manually configured.B、Only PortFast is specified in 802.1w；UplinkFast and BackboneFast must be manually configured.C、None of the proprietary Cisco enhancements are specified in 802.1w.D、PortFast，UplinkFast，and BackboneFast are specified in 802.1w.
You have just reinstalled a VIP 6-80 in a Cisco 7500 Series router. What must you do to bring up the port adapter interfaces?（）A、All interfaces are online by default once the VIP is up and running normally.B、All interfaces must be manually brought online, even those previously configured.C、The previous VIP configuration must be reloaded to bring interfaces online.D、Any interfaces not previously configured must be manually configured and brought online.
A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）A、The adapter must be taken offline prior to the firmware updateB、The adapter must be assigned to the service partition prior to the firmware updateC、The system has not been rebooted since the adapter was added to the Logical PartitionD、The adapter must be dynamically removed from the Logical Partition prior to the firmware update
Prior to implementing an LPAR system， which of the following needs to be done？（）A、A graphics monitor must be attached to the serverB、Cluster System Management （CSM） software must be installedC、The LPAR system must have an Hardware Management Console （HMC） connectedD、Each LPAR must be configured with a CDROM for operating system installation
An administrator issued a command to update the firmware of an Ethernet adapter on a partitioned system， but received an error. What is the most likely cause of the problem？（）A、The adapter must be taken offline prior to the firmware update.B、The system has not been rebooted since the adapter was added to the LPAR.C、The adapter must be assigned to the service partition prior to updating the firmware.D、The adapter must be dynamically removed from the LPAR prior to updating the firmware.
A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）A、A public internet connectionB、All of the Logical Partitions need to be activeC、One partition must be configured with Service AuthorityD、A local Repository must be configured prior to the update
多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.
多选题What are two requirements when using AppFlow?（） (Choose two.)AQuality of service must be enabled.BNSC compression must be enabled.CPFA's TCP Acceleration (AFP) must be enabled.DAppFlow must be configured on the client-side device first.
多选题What are two requirements when using AppFlow? （）(Choose two.)AQuality of service must be enabled.BNSC compression must be enabled.CPFA's TCP Acceleration (AFP) must be enabled.DAppFlow must be configured on the client-side device first
单选题When configuring VLANs on an autonomous access point，what must be configured on theconnected switchport？（）A802.1q trunkingBVTP trunkingCISL trunkingDDPT trunking
多选题The hardware and software configurations for vPC+ are similar to that of traditional vPC. What are the differences in the configuration of vPC+？ （）AFabricPath switch ID must be configured under the vPC domain.BVirtual switch ID of vPC+ must be configured under FabricPath domain.COn Cisco Nexus 7000 Series Switch， F1 interfaces must be used as the vPC+ peer links.DThe vPC+ peer link must be configured as a Cisco FabricPath core port （switchport mode fabricpath）.EFabricPath subswitch ID must be configured under the vPC domain.
单选题What must be configured on the Cisco Unity Express host router prior to installation of the CUE module?（）ASet up the Network Time Protocol server. BInstall the files needed to run the web-based GUI. CSet up routing and IP addressing on the service module and the interface service engine. DConfigure a session initiation protocol dial peer for connecting calls to the voice mail and Auto Attendant features.
单选题When configuring vlans on an autonomous access point. What must be configured on the connected switchport？（）A802.1q trunkingBvtp trunkingCisl trunkingDdpt trunking
单选题An administrator issued a command to update thefirmware of an Ethernet adapter on a partitioned system, but received an error. What is the most likely cause of the problem?（）AThe adapter must be taken offline prior to the firmware update.BThe system has not been rebooted since the adapter was added to the LPAR.CThe adapter must be assigned to the service partition prior to updating the firmware.DThe adapter must be dynamically removed from the LPAR prior to updating thefirmware.
单选题What must be configured prior to the first commit after factory defaults are loaded?（）Aroot authenticationBdefault gatewayChostnameDmanagement services
单选题A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）AA public internet connectionBAll of the Logical Partitions need to be activeCOne partition must be configured with Service AuthorityDA local Repository must be configured prior to the update
单选题Prior to implementing an LPAR system， which of the following needs to be done？（）AA graphics monitor must be attached to the serverBCluster System Management （CSM） software must be installedCThe LPAR system must have an Hardware Management Console （HMC） connectedDEach LPAR must be configured with a CDROM for operating system installation
单选题When configuring the Cisco VPN Client，what action is required prior to installing Mutual Group Authentication？（）ATransparent tunneling must be enabled.BA valid root certificate must be installed.CA group pre-shared secret must be properly configured.DThe option to Allow Local LAN Access must be selected.
单选题What is a limitation of implementing uRPF？（）AMPLS LDP must be enabled.BBGP routing protocol must be running.CNamed access-lists must be configured.DSymmetrical routing is required.EDomain name must be defined
单选题What must be configured prior to the first commit after factory defaults are loaded?（）Aroot authenticationBdefault gatewayChost nameDmanagement services