下图中如果允许192.168.1.0/24和10.0.0.0/8的网络之间通信，必须要配置的两条命令是什么()A.A(config)iproute 10.0.0.0 255.0.0.0 172.16.40.2B.A(config)iproute 10.0.0.0 255.0.0.0 S0/0/0C.A(config)iproute 10.0.0.0 255.0.0.0 10.0.0.1D.B(config)iproute 192.168.1.0 255.255.255.0 172.16.40.1E.B(config)iproute 192.168.1.0 255.255.255.0 172.16.40.2F.Biproute 192.168.1.0 255.255.255.0 192.168.1.1
下图中如果允许192.168.1.0/24和10.0.0.0/8的网络之间通信，必须要配置的两条命令是什么()
A.A(config)iproute 10.0.0.0 255.0.0.0 172.16.40.2
B.A(config)iproute 10.0.0.0 255.0.0.0 S0/0/0
C.A(config)iproute 10.0.0.0 255.0.0.0 10.0.0.1
D.B(config)iproute 192.168.1.0 255.255.255.0 172.16.40.1
E.B(config)iproute 192.168.1.0 255.255.255.0 172.16.40.2
F.Biproute 192.168.1.0 255.255.255.0 192.168.1.1
相关考题：
如下图所示为三台路由器的连接与IP地址分配，在R2中配置到达子网192.168.1.0/24的静态路由的命令是( )。A) R2(config)#ip route 192.168.1.2 255.255.255.0 10.1.1.2B) R2(config)#ip route 192.168.1.1 255.255.255.0 10.1.1.2C) R2(config)#ip route 192.168.1.2 255.255.255.0 10.1.1.1D) R2(config)#ip route 192.168.1.0 255.255.255.0 10.1.1.1
Cisco路由器执行show access-list命令显示如下一组信息 Standard IP access list block deny 10.0.0.0, wildcardbits 0.255.255.255 log deny 172.16.0.0, wildcard bits 0.15.255.255 permit any 根据上述信息，正确的access-list配置是A．Router (config) #access-list standard block Router (config-std-nacl) #deny 10.0.0.0 255.0.0.0 log Router (config-std-nacl) #deny 172.16.0.0 255.240.0.0 Router (config-std-nacl) #permit anyB．Router (config) #ip access-list standard block Router (config-std-nacl) #permit any Router (config-std-nacl) #deny 10.0.0.0 0.255.255.255 log Router (config-std-nacl) #deny 172.16.0.0 0.15.255.255C．Router (config) #ip access-list standard block Router (config-std-nacl) #deny 10.0.0.0 255.0.0.0 log Router (config-std-nacl) #deny 172.16.0.0 255.240.0.0 Router (config-std-nacl) #permit anyD．Router (config) #ip access-list standard block Router (config-std-nacl) #deny 10.0.0.0 0.255.255.255 log Router (config-std-nacl) #deny 172.16.0.0 0.15.255.255 Router (config-std-nacl) #permit any
以下配置静态路由的命令中，哪项是正确的?______。A．R2 (config) #ip route 192.168.1.5.0.0.0.255 10.1.1.2B．R2 (config) #ip route 192.168.1.5 255.255.254.0 10.1.1.2C．R2 (config) #ip route 192.168.1.5 255.255.255.0 10.1.1.2D．R2 (config) #ip route 192.168.1.5 255.0.0.0 10.1.1.2
以下配置默认路由的命令正确的是：A.Quidway(config)iproute 0.0.0.0 0.0.0.0 172.16.2.1B.Quidway(config)iproute 0.0.0.0 255.255.255.255 172.16.2.1C.Quidway(config-if-s0)iproute 0.0.0.0 0.0.0.0 172.16.2.1D.Quidway(config)iprouter 0.0.0.0 0.0.0.0 172.16.2.1
下列哪个network命令会告知此路由器开始使用IP地址为10.1.1.1、10.1.100.1和10.1.120.1的接口上的OSPF（）A.network 10.0.0.0 255.0.0.0 area 0B.network 10.0.0.0 0.255.255.255 area 0C.network 10.0.0.1 0.0.0.255 area 0D.network 10.0.0.1 0.0.255.255 area 0
以下配置静态路由的命令中，哪项是正确的?——A．R2(config)#ip route 192．168．1．5 0．0．0．255 10．1．1．2B．R2(config)#ip route 192．168．1．5 255．255．254．0 10．1．1．2C．R2(config)#ip route 192．168．1．5 255．255．255．0 10．1．1．2D．R2(config)#ip route 192．168．1．5 255．0．0．0 10．1．1．2
下列静态路由配置正确的是()A.iproute 192.168.1.1 255.255.255.0 serial0/0B.iproute 192.168.1.0/24 172.16.1.1C.iproute 192.168.1.0 255.255.255.0172.16.1.0D.iproute 192.168.1.0 255.255.255.0172.16.1.1
哪个命令能为下图中R1上配置正确的静态默认路由()A.R1(config-if)iproute 0.0.0.0 0.0.0.0 s0/0/0B.R1(config)iproute 0.0.0.0 0.0.0.0 s0/1/0C.R1(config)iproute 0.0.0.0 0.0.0.0 192.168.12.1D.R1(config)iproute 0.0.0.0 0.0.0.0 192.168.12.2
下面哪条命令是正确的，如果要将192.168.1.0/24的业务网段发到OSPF的area0（)A.Router(config-router)network 192.168.1.0 0.0.0.2550B.Router(config-router)network 192.168.1.0 0.0.0.255 area0C.Router(config-router)network 192.168.1.0 255.255.255.255 area0D.Router(config-router)network 192.168.1.0 0.0.0.0 area0
下表是该系统中路由器的IP地址分配表。请根据上图完成以下R3路由器的配置：R3(config)interface e0/1(进入接口e0/1配置模式)R3(coafig-if) ip address 202.115.13.254(4)(设置IP地址和掩码)R3(config) interface s0/0(进入串口配置模式)R3(config-if) ip address(5)255.255.255.0(设置IP地址和掩码)R3(config) interface s0/1R3(config-if)ip address(6)255.255.255.0R3(config) interface s0/2R3(eonfig-if)ip address(7)255.255.255.0R3(config) interface s0/3R3(eonfig-if)ip address(8)255.255.255.0R3(config) interface s0/4R3(config-if)ip address(9)255.255.255.0R3(config) interface s0/5R3(config-if) ip address(10)255.255.255.0
以下配置默认路由的命令正确的是()。A.[Quidway]iproute-static0.0.0.00.0.0.0172.16.2.1B.[Quidway]iproute-static0.0.0.0255.255.255.255172.16.2.1C.[Quidway-serial0]iproute-static0.0.0.0320.0.0.0D.[Quidway]iproute-static0.0.0.010.0.0.1
配置路由器默认路由的命令是__（67）__。A．iproute 220.117.15.0 255.255.255.0 0 0.0.0.0B．iproute 220.117.15.0 255.255.255.0 220.117.15.1C．iproute 0.0.0.0 255.255.255.0 220.117.15.1D．iproute 0.0.0.0 0.0.0.0 220.117.15.1
如果在互联网中添加了一个局域网，要用手工方式将该局域网添加到路由表中，应使用的命令是（ ）。A.router（config）ip route 2.0.0.0 255.0.0.0 via 1.0.0.2 B.router（config）ip route 2.0.0.0 255.0.0.0 1.0.0.2 C.router (config) ip route 2.0.0.0 via 1.0.0.2 D.router (config) ip route 2.0.0.0 1.0.0.2 mask 255.0.0.0
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?() A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1B. R4(config)# ip default - network 10.0.0.0C. R4(config - router)# default -information originateD. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
Refertotheexhibit.EIGRPhasbeenconfiguredonallroutersinthenetwork.WhatadditionalconfigurationstatementshouldbeincludedonrouterR4toadvertiseadefaultroutetoitsneighbors?() A.R4（config）#ipdefault-network10.0.0.0B.R4（config）#iproute0.0.0.00.0.0.010.1.1.1C.R4（config）#iproute10.0.0.0255.0.0.010.1.1.1D.R4（config-router）#default-informationoriginate
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)router ospf 1Router(config-router)network 10.0.0.0 255.0.0.0 area 0A. The process id is configured improperlyB. The OSPF area is configured improperlyC. The network wildcard mask is configured improperlyD. The network number is configured improperlyE. The AS is configured improperlyF. The network subnet mask is configuerd improperly
Refer to the graphic. A static route to the 10.5.6.0／24 network is to be configured on the HFD router. Which commands will accomplish this? () A.HFD（config）#iproute10.5.6.00.0.0.255fa0/0B.HFD（config）#iproute10.5.6.00.0.0.25510.5.4.6C.HFD（config）#iproute10.5.6.0255.255.255.0fa0/0D.HFD（config）#iproute10.5.6.0255.255.255.010.5.4.6E.HFD（config）#iproute10.5.4.60.0.0.25510.5.6.0F.HFD（config）#iproute10.5.4.6255.255.255.010.5.6.0
Usersonthe192.168.1.0／24networkmustaccessfileslocatedontheServer1.WhatroutecouldbeconfiguredonrouterR1forfilerequeststoreachtheserver?() A.iproute0.0.0.00.0.0.0s0/0/0B.iproute0.0.0.00.0.0.0209.165.200.226C.iproute209.165.200.0255.255.255.0192.168.1.250D.iproute192.168.1.0255.255.255.0209.165.100.250
3台路由器的连接与IP地址分配如下图所示，在R2中配置到达子网192．168．1．0／24的静态路由的命令是——。A．R2(config)#ip route 192．168．1．0 255．255．255．O lO．1．1．1B．R2(config)#ip route 192．168．1．2 255．255．255．0 10．1．1．1C．R2(config)#ip route 192．168．1．1 255．255．255．0 10．1．1．2D．R2(config)#ip route 192．168．1．2 255．255．255．0 10．1．1．2
某单位的办公网和商务网通过路由器R1、R2、R3与Internet相连，网络连接和IP地址分配如图1所示。该单位要求通过RIP路由协议使办公网和商务网之间能够互相通信，并正常访问Internet请阅读以下R1的配置信息，并补充【6】~【10】空白处的配置命令或参数。按题目要求完成R1的正确配置。RouterenableRouterRouterconfigure terminalRouter(config)Router(config)hostname R1R1(config)interface f0/1R1(config-if)ip address 202.206.16.1 255.255.255.0R1(config-if)no shutdownR1(config-if)interfacef0/2R1(config-if)ip adress 202.206.17.1 255.255.255.0R1(config-if)no shutdownR1(config-if)exitR1(config)R1(config)interface s1R1(config-if)vlan ip adress 202.112.41.144 255.255.255.252R1(config-if)bandwidth 【6】 配置带宽为2.048MbpsR1(config-if)【7】 PPP 封装PPP协议R1(config-if)noshutdownR1(config-if)exitR1(config-if)iproute 【8】 配置缺省路由R1(config-if)router ripR1(config-router)network 【9】 配置参与RIP的网络R1(config-router)network 【10】 配置参与RIP的网络R1(config-router)endR1writeR1
要在路由器上配置一条静态路由。已知目的地址为192.168.1.0，掩码是20位，出接口为GigabitEthernet0/0，出接口IP地址为10.10.202.1，那么下列配置中哪些是正确的？（）。A、iproute-static192.168.1.0255.255.240.0GigabitEthernet0/0B、iproute-static192.168.1.0255.255.248.010.10.202.1C、iproute-static192.168.1.0255.255.240.010.10.202.1D、iproute-static192.168.1.0255.255.248.0GigabitEthernet0/0
下列静态路由配置正确的是（ ）。A、iproute129.1.0.016seriAl0B、iproute10.0.0.216129.1.0.0C、iproute129.1.0.01610.0.0.2D、iproute129.1.0.0255.255.0.010.0.0.2
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
单选题Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors？（）A R4（config）# ip default-network 10.0.0.0B R4（config）# ip route 0.0.0.0 0.0.0.0 10.1.1.1C R4（config）# ip route 10.0.0.0 255.0.0.0 10.1.1.1D R4（config-router）# default-information originate
单选题下面哪条命令用于在路由器上添加一条默认路由？（）ARouter#iproute0.0.0.00.0.0.0192.168.100.1BRouter#iproute0.0.0.0255.255.255.255192.168.100.1CRouter（Config）#iproute0.0.0.00.0.0.0192.168.100.1DRouter（Config）#iproute0.0.0.0255.255.255.255192.168.100.1