During startup, router VE1 displays the following error message:boot: cannot open "flash:"What will VE1 do next?A. It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.B. It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.C. It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.D. Because of damaged flash memory, the router will fail the POST.E. It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.F. None of the above
During startup, router VE1 displays the following error message:
boot: cannot open "flash:"
What will VE1 do next?
A. It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.
B. It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.
C. It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
D. Because of damaged flash memory, the router will fail the POST.
E. It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.
F. None of the above
相关考题：
What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?A．It will search for the configuration file in the locations specified by boot system commands.B．It will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D．It will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
Given the following router output,which configuration file will the router use at its next reload?() A.configB.clientqos.cnfC.startup-configD.running-configuration
During the boot sequence, a Ezonexam 2800 series router needs to locate and load an operating system. What is the default order the router uses to find an operating system?A．ROM, TFTP server, FlashB．Flash, TFTP server, ROMC．Flash, NVRAM, TFTP serverD．Flash, ROM, TFTP serverE．Flash, TFTP server, RAM
What will a router do during startup if a configuration file is not located in NVRAM?() A. it will search for the configuration file in the locations specified by boot system commands.B. it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D. it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with:Would you like to enter the initial configuration dialog? [yes/no]Why has this occurred?（）A. There is an error in the router DRAM.B. Te IOS image is corrupt.C. The configuration register is set to 0x2142.D. The TFTP server that contains the router configuration file is unreachable.E. A boot system configuration command has placed the router into setup mode.
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?() A. Flash,TFTP server,ROMB. Flash,NVRAM,ROMC. ROM,NVRAM,TFTP serverD. NVRAM,TFTP server,ROME. TFTP server,Flash,NVRAM
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? () A.Router1 has specific boot system command that instruct it to load IOS from TFTP server.B.Router1 is acting as a TFTP server for other routers.C.Router1 cannot locate a valid IOS image in flash memory.D.Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.E.Cisco routers will first attempt to load a image from TFTP for management purposes.
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next?() A.It checks the configuration registerB.It attempts to boot from a TFTP serverC.It loads the first image file in flash memoryD.It inspects the configuration file in NVRAM for boot instructions
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?() A.It checks the configuration registerB.It attempts to boot from a TFTP serverC.It loads the first image file in flash memoryD.It inspects the configuration file in NVRAM for boot instructions
There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?() A.Flash,TFTPserver,ROMB.Flash,NVRAM,ROMC.ROM,NVRAM,TFTP serverD.NVRAM,TFTP server,ROME.TFTP server,Flash,NVRAM
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next()。 A.Because of damaged flash memory, the router will fail the POST.B.It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.C.It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.D.It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.E.It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload()。 A.TFTP server, Flash, NVRAMB.ROM, NVRAM, TFTP serverC.NVRAM, TFTP server, ROMD.Flash, TFTP server, ROME.Flash, NVRAM, ROM
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）A、Because of damaged flash memory， the router will fail the POSTB、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROMD、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）A、There is an error in the router DRAM.B、Te IOS image is corrupt.C、The configuration register is set to 0x2142.D、The TFTP server that contains the router configuration file is unreachable.E、A boot system configuration command has placed the router into setup mode.
A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?（）A、It checks the configuration register.B、It attempts to boot from a TFTP server.C、It loads the first image file in flash memory.D、It inspects the configuration file in NVRAM for boot instructions.
What will a router do during startup if a configuration file is not located in NVRAM?（）A、it will search for the configuration file in the locations specified by boot system commands.B、it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D、it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）A、Flash,TFTPserver,ROMB、Flash,NVRAM,ROMC、ROM,NVRAM,TFTP serverD、NVRAM,TFTP server,ROME、TFTP server,Flash,NVRAM
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequencethat router will use to find an ios during reload？（）A、Flash，TFTP server，ROMB、Flash，NVRAM，ROMC、ROM，NVRAM，TFTP serverD、NVRAM，TFTP server，ROME、TFTP server，Flash，NVRAM
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next？（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）A、Router1 has specific boot system command that instruct it to load IOS from TFTP server.B、Router1 is acting as a TFTP server for other routers.C、Router1 cannot locate a valid IOS image in flash memory.D、Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.E、Cisco routers will first attempt to load a image from TFTP for management purposes.
QUESTION 14 You have a computer that contains a DVD drive and a single 350-GB hard disk drive. You attempt to installWindows 7 on the computer by using the DVD installation media and receive the following error message:Reboot and Select proper Boot device or Insert Boot Media in selected Boot device. You need to ensurethat you can install Windows 7 on the computer by using the DVD installation media. What should you do?（）A、From the BIOS, modify the startup order.B、From the BIOS, enable Pre-Boot Execution Environment (PXE).C、Create an answer file named oobe.xml and place the file on the hard disk drive.D、Create an answer file named autounattend.xml and place the file on the hard disk drive.
多选题Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）ARouter1 has specific boot system command that instruct it to load IOS from TFTP server.BRouter1 is acting as a TFTP server for other routers.CRouter1 cannot locate a valid IOS image in flash memory.DRouter1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.ECisco routers will first attempt to load a image from TFTP for management purposes.
单选题A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?（）AIt checks the configuration register.BIt attempts to boot from a TFTP server.CIt loads the first image file in flash memory.DIt inspects the configuration file in NVRAM for boot instructions.
单选题During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。ABecause of damaged flash memory, the router will fail the POST.BIt will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.CIt will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.DIt will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.EIt will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
单选题There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload?（）ATFTP server, Flash, NVRAMBROM, NVRAM, TFTP serverCNVRAM, TFTP server, ROMDFlash, TFTP server, ROMEFlash, NVRAM, ROM
单选题There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）AFlash,TFTPserver,ROMBFlash,NVRAM,ROMCROM,NVRAM,TFTP serverDNVRAM,TFTP server,ROMETFTP server,Flash,NVRAM