Which of the following protocols would be used in order to log into a router to configure a VLAN?() A.RDPB.SMTPC.TELNETD.FTP
Which of the following protocols would be used in order to log into a router to configure a VLAN?()
A.RDP
B.SMTP
C.TELNET
D.FTP
相关考题：
下面哪一条命令可以正确的为Vlan 5定义一个子接口?() A.Router（config-if）#encapsulation dotq 5B.Router（config-if）#encapsulation dotq vlan 5C.Router（config-subif）#encapsulation dotq 5D.Router（config-subif）#encapsulation dotq vlan 5
You’re going to have a quiz ( )by another two in the ( )month. A. followed,followedB. followed,followingC. following,followedD. following,following
仔细阅读以下与路由器(Router)的快速以太网接口实现不同VLAN间路由的相关配置信息，结合图 3-12所示的拓扑结构图，将(3)～(7)空缺处的内容填写完整，以实现相应的配置任务。Router＞enable (进入特权模式)Routerconfig terminalRouter (config) interface fastethernet 0/0Router (config-if) ip address (3)Router (config-if) no shutdownRouter (config-if) (4)Router (config-subif) encapsulation dotlq2Router (config-subif) ip address (5)Router (config-sobif) interface fastethemet 0/0.2Router (config-subif) (6)Router (config-subif) ip address (7)Router (config-subif) endRouter
Youwanttopurgejobentriesolderthan5daysfromthejoblog.Youdonotwanttopurgewindowlogentries.Whichcommandwillyouusetoaccomplishthistask?() A.EXECUTEDBMS_SCHEDULER.PURGE_LOG（log_history=5，job_name=’JOB1’）；B.EXECUTEDBMS_SCHEDULER.PURGE_LOG（log_history=5，job_name=’JOB_LOG’）；C.EXECUTEDBMS_SCHEDULER.PURGE_LOG（log_history=5，which_log=’JOB1’）；D.EXECUTEDBMS_SCHEDULER.PURGE_LOG（log_history=5，which_log=’JOB_LOG’）；
To set the history retention period for either window logging or job logging individually, which parameters of the SET_SCHEDULER_ATTRIBUTE procedure need to be used?() A. LOG_HISTORYB. JOB_LOG_RETENTIONC. WINDOW_LOG_RETENTIOND. WHICH_LOGE. LOG_NAME
某网络的拓扑结构如图4-1所示，其中路由器Router1和交换机Switch1的部分配置如下：以下是路由器Router和Switch1的部分配置信息，请解释部分命令的意义。Router(config)interface fastEthernet1/0.1Router(config-subif)encapsulation isl 11 (1)Router(config-subif)ip address 10.1.1.1 255.255.255.0 (2)Router(config-subif)exitRouter(config)interface fastEthernet1/0.2Router(config-subif)encapsulation isl 12Router(config-subif)ip address 10.1.2.1 255.255.255.0Router(config-subif)exitRouter(config)interface fastEthernet1/0.3Router(config-subi f)encapsulation isl 13Router(config-subif)ip address 10.1.3.1 255.255.255.0Router(config-subif)exitRouter(config)ip routing (3)[交换机Switch1的部分配置信息]Switch1(config)vlan database (4)Switch1(vlan)vlan 11 (5)Switch1(vlan)vlan 12Switch1(vlan)vlan 13Switch1(vlan)exitSwitch1(config)interface fastEthernet0/0Switch1(config-if)switchport mode trunk (6)Switch1(config-if)switchport trunk allowed all (7)Switch1(config-if)exitSwitch1(config)interface fastEthernet0/1Switch1(config-if)switchport mode trunkSwitch1(config-if)switchport trunk a110wed a11Switch1(config-if)exitSwitch1(config)interface fastEthernet0/2Switch1(config-if)switchport mode trunkSwitch1(config-if)switchport trunk allowed allSwitch1(config-if)exit
AcustomerisdeployinganewdatabaseonaPS701BladeinaBladeCenterH,andrequiresredundant networkandSANadapters.Whichconfigurationsupportsthecustomerrequirement?() A.Configure2CFFhcombinationfibrechannel/gigabitEthernetadaptersB.Configure1CFFh2-portfibrechanneladapterand1CIOv2-portgigabitEthernetadapterC.Configure1CIOv2-portfibrechanneladapterand1CFFhcombinationfibrechannel/gigabitEthernet adapterD.Configure1CIOv2-portgigabitEthernetadapterand1CFFhcombinationfibrechannel/gigabitEthernet adapter
下面哪一条命令可以正确地为 VLAN 5定义一个子接口 （)。A．Router（config-if ）#encapsulation dot1q 5B．Router（config-if ）#encapsulation dot1q vlan 5C．Router（config-subif ）#encapsulation dot1q 5D．Router（config-subif ）#encapsulation dot1q vlan 5
下面哪一条命令可以正确地为VLAN5定义一个子接口（）A．Router(config-if)#encapsulation dot1q 5B．Router(config-if)#encapsulation dot1q VLAN 5C．Router(config-subif)#encapsulation dot1q 5D．Router(config-subif)#encapsulation dot1q VLAN 5
下面哪一条命令可以正确的为Vlan 5定义一个子接口？（)A．Router (config-if) #encapsulation dotq 5B．Router (config-if) #encapsulation dotq vlan 5C．Router (config-subif) #encapsulation dotq 5D．Router (config-subif) #encapsulation dotq vlan 5