设置Trunk口许可所有VALN通过的命令是（）A、name vlanB、interface vlanC、vlan enableD、switchport trunk allowecvlan all
设置Trunk口许可所有VALN通过的命令是（）
- A、name vlan
- B、interface vlan
- C、vlan enable
- D、switchport trunk allowecvlan all
相关考题：
在锐捷接换机上配置Trunk接口时,如果要从允许的VLAN列中删除VLAN5,所运行的命令是哪一项?() A.Switch（config-if）#Switchport trunk allowed remove 5B.Switch（config-if）#Switchport trunk remove 5C.Switch（config-if）#Switchport trunk Vlan allowed remove 5D.Switch（config-if）#Switchport trunk allowed Vlan remove 5
如下图所示，3com和Cisco公司的交换机相互连接，在两台交换机之间需传输ULANID为1、10、20和30的4个VLAN信息，Catalyst 3548交换机VLAN Trunk的正确配置是A．Switch-3548 (config-if) #switchport trunk encapsulation dot 1 q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30B．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation isl Switch-3548 (config-if) #switchport trunk allowed vlan 1-30C．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation negotiate Switch-3548 (config-if) #switchport trunk allowed vlan 1-30D．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation dot 1q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30
以下两个配置中错误的是 (6) ，原因是 (7) 。A．Switch0(config)interface gigabitEthernet 0/3Switch0(config-if)swi七chport mode trunkSwitch0(config-if)switchpor trunk encapsulation dotlqSwitch0(config)exitSwitch0 vlan databaseSwitch0(vlan) vlan2100 name lab02B．Switch0(config)interface gigabitEthernet 0/3Switch0(config-if) switchport mode trunkSwitch0(config-if) switchport trunk encapsulation ISLSwitch0(config)exitSwitch0 vlan databaseSwitch0(vlan) vlan2100 name lab02
阅读下面的配置信息，解释(5)处的命令。SwitchSwitchconfigSwitch(config)interface f0/1(进入接口1配置模式)Switch(config-if)switchport mode trunk(5)Switch(config-if)switchpoft trunk allowed vlan all(设置允许从该接口交换数据的VLAN)Switch(config-if)exitSwitch(config)exitSwitCh
阅读以下说明，回答问题1至问题3，将解答填入解答栏内。【说明】某公司租用了一段C类地址203.12.11.0/24～203.12.14.0/24，如下图所示。其网间地址是172.11.5.14/24。要求网内所有PC都能上网。接入层交换机Switch1的端口24为trunk口，其余各口属于vlan11，请解释下列命令并完成交换机的配置。Switch1config terminalSwitch1(config)interface f0/24(进入端口24配置模式)Switch1(config-if) switchport mode trunk(1)Switch1(config-if)switchport trunk encapsulation dotlq(2)Switch1(config-if) switchport trunk allowed all(允许所有VLAN从该端口交换数据)Switch1(config-if)exitSwitch1(config)exitSwkch1 vlan databaseSwitch1(vlan) vlan11 name lab01(3)Switch1(vlan)exitSwitch1 config terminalSwitch1(config)interface f0/9(进入f0/9的配置模式)Switch1(config-if)(4)(设置端口为接入链路模式)Switch1(config-if)(5)(把f0/9分配给VLAN11)Switch1(config-if)exitSwitch1(config)exit
以下两个配置中错误的是(6)，原因是(7)。A．Swkch0(config)interface gigabitEthernet 0/3Switch0(config-if)switchport mode trunkSwitch0(config-if)switchport trunk encapsulation dotlqSwnch0(config)exitSwitch0 vlan databaseSwitch0(vlan) v1an 2100 name lab02B．Switch0(config) interface gigabirEthernet 0/3Switch0(config-if)switchport mode trunkSwitch0(config-if)switchport trunk encapsulation ISLSwitch0(config)exitSwiteh0 vlan darabaseSwitch0(vlan) vlan 2100 name lab02
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?() A. Switch(config-if)# vlan allB. Switch(config-if)# switchport trunk encapsulation dot1qC. Switch(config-if)# switchport access vlan allD. Switch(config-if)# switchport mode trunkE. Switch(config-if)# switchport access vlan 303
What is the function of the command switchport trunk native vlan 999 on a switch?() A. It designates VLAN 999 for untagged traffic.B. It blocks VLAN 999 traffic from passing on the trunk.C. It creates a VLAN 999 interface.D. It designates VLAN 999 as the default for all unkown tagged traffic.
What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch()。 A.It creates a VLAN 999 interface.B.It designates VLAN 999 for untagged traffic.C.It blocks VLAN 999 traffic from passing on the trunk.D.It designates VLAN 999 as the default for all unknown tagged traffic.
在配置交换机Trunk接口的VLAN许可列表时，是用all选项的含义是（）A、许可VLAN列表包含当前创建的所有VLANB、许可VLAN列表剪掉当前除VLAN1之外的所有VLANC、许可VLAN列表包含VLAN1-VLAN4094D、许可VLAN列表包含当前存在成员接口的VLAN
锐捷交换机VLAN修剪命令格式是下列哪条命令？（）A、switchport trunk allowed vlan remove vidB、switchport trunk remove vidC、switchport trunk prune vidD、switchport trunk allowed vid
如果要把交换机Trunk的许可VLAN列表改为默认的许可所有VLAN的状态，应该使用命令（）A、no switchporttrunkallowedvlanB、default switchpor t trunkallowed vlanC、switchport trunk allowed vlan resetD、reset switchport trunk allowed vlan
Given the following configuration， what command can be used to determine the physical path that traffic will be sent out upon？（） Port-profile type Ethernet name vm-data Switchport mode trunk Switchport trunk allowed vlan 200-210 Channel-group auto mode on mac-pinning State enabled Vmware port-group No shut Port-profile type vethernet name vlan-200 Switchport mode access Switchport vlan 200 State enabled Vmware port-group No shut A、 module vem X execute vemcmd show trunkB、 show module 3 internal pinningC、 module vem X execute vemcmd show portD、 show module vem mappingE、 show interface vethX pinning
What is the function of the command switchport trunk native vlan 999 on a？（）A、It designates VLAN 999 for untagged traffic.B、It blocks VLAN 999 traffic from passing on the trunk.C、It createsa VLAN 999 interface.D、It designates VLAN 999 as the default for all unkown tagged traffic.
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）A、Switch(config-if)# vlan allB、Switch(config-if)# switchport trunk encapsulation dot1qC、Switch(config-if)# switchport access vlan allD、Switch(config-if)# switchport mode trunkE、Switch(config-if)# switchport access vlan 303
交换机如何将接口设置为TAG VLAN模式？（）A、switchport mode tagB、switchport mode trunkC、trunk onD、set port trunk on
在交换机的配置中，能够正确地将NativeVLAN设置为VLAN5的命令是（）。A、switchport native vlan 5B、switchport trunk native 5C、switchport native trunk vlan 5D、switchport trunk native vlan 5
把VLAN20从中继链路中删除的命令是（）A、switch（config-if）#switchport trunk vlan remove 20B、switch（config-if）#switchport trunk allowed vlan remove 20C、switch（config）#switchport trunk vlan remove 20D、switch（config）#switchport trunk allowed vlan pruning 20
中兴ZXCTN设备在进行初始化时，以下哪个选项命令是不属于MCC监控命令的脚本（）A、snmp-server packetsize 8192B、interface vlan 3001；ip address 139.9.1.6255.255.255.252；exitC、vlan3001；exitD、interface xgei_9/1；mcc-vlanid3001；switchport mode trunk；switch port trunk vlan 3001；switch port trunk native vlan 3001；exit
A Cisco switch has this configuration for a port channel connecting to an ESXi using dual NICs and is intended for use with an N1Kv. Interface fastethernet 1/10 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface fastethernet 1/11 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface port-channel 10 Switchport mode trunk Switchport allowed vlan all No shut Which Port Channel configuration must be used on the Nexus 1000v port-profile？（）A、 MAC pinningB、 Cisco Discovery Protocol pinningC、 Mode OnD、 Mode ActiveE、 No port channel configuration
You are the network administrator at Company and switch R1 is configured as shown below： Interface gigethernet 0/1 Switchport mode trunk Switchport trunk encapsulation dot1q Switchport trunk native vlan 5 If untagged frames are arriving on interface gigethernet 0/1 of R1， which of the following statement are correct？（）A、 Untagged frames are automatically assumed to be in VLAN 5.B、 Untagged frames are defaulted to VLAN 1 traffic.C、 Untagged frames are dropped because all packets are tagged when dot1q trunked.D、 Untagged frames are determined on the other switchE、 Untagged frames are not supported on 802.1Q trunks.
单选题What is the function of the command switchport trunk native vlan 999 on a switch?（）AIt designates VLAN 999 for untagged traffic.BIt blocks VLAN 999 traffic from passing on the trunk.CIt creates a VLAN 999 interface.DIt designates VLAN 999 as the default for all unkown tagged traffic.
单选题如下图所示，3com和Cisco公司的交换机相互连接，在两台交换机之间需传输VLAN ID为1、10、20和30的5个VLAN信息，Catalyst3548交换机VLAN Trunk的正确配置是（ ）。ASwitch-3548（config-if）#switchport trunk encapsulation dotlqSwitch-3548（config-if）#switchport trunk allowed vlan 1，10，20，30BSwitch-3548（config-if）#switchport mode trunkSwitch-3548（config-if）#switchport trunk encapsulation islSwitch-3548（config-if）#switchport tnmk allowed vlan 1-30CSwitch-3548（config-if）#switchport mode trunkSwitch-3548（config-if）#switchport trunk encapsulation negotiateSwitch-3548（config-if）#switchport trunk allowed vlan 1-30DSwitch-3548（config-if）#switchport mode trunkSwitch-3548（config-if）#switchport trunk encapsulation dotlqSwitch-3548（config-if）#switchport trunk allowed vlan 1，10，20，30
多选题Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）ASwitch(config-if)# vlan allBSwitch(config-if)# switchport trunk encapsulation dot1qCSwitch(config-if)# switchport access vlan allDSwitch(config-if)# switchport mode trunkESwitch(config-if)# switchport access vlan 303
单选题设置Trunk口许可所有VALN通过的命令是（）Aname vlanBinterface vlanCvlan enableDswitchport trunk allowecvlan all
单选题What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?（）AIt creates a VLAN 999 interface.BIt designates VLAN 999 for untagged traffic.CIt blocks VLAN 999 traffic from passing on the trunk.DIt designates VLAN 999 as the default for all unknown tagged traffic.