7750SR和Cisco路由器无法建立邻接关系，你猜测原因是由于本地接口MTU值与对端接口MTU值不匹配。请使用下面一条命令确认是否存在错误的MTU（） A、show router ospf statisticsB、show router ospf neighborC、show router ospf statusD、show router ospf interface
7750SR和Cisco路由器无法建立邻接关系，你猜测原因是由于本地接口MTU值与对端接口MTU值不匹配。请使用下面一条命令确认是否存在错误的MTU（）
- A、show router ospf statistics
- B、show router ospf neighbor
- C、show router ospf status
- D、show router ospf interface
相关考题：
要显示路由器的运行配置，下面的路由器命令中，哪一条是正确的?——A．Router#show running—configB．Router#show startup—configC．Router‘#show configurationD．Routershow running—config
输入哪条命令可以看到以下信息?（ ） LS DataBase Type :Router Ls id :10.1.2.2 Ady rtr :1050 Len :72 Seq :80000008 Cksum (DC) Area Border Router Link count 4 Link id :192.168.2.1 Data :255.255.255.255 Metric:1562 Link id :10.1.2.2 Data :10.1.3.1 Type :Router Metric :1562 Link id :10.1.3.2 Data :255.255.255.255 Type :StubNet Metric :1562A.show ip routeB.show ip ospf isaC.show ip ospf databaseD.show ip ospf interface
输入哪条命令可以看到以下信息()。A.show ip routeB.show ip ospf isaC.show ip ospf databaseD.show ip ospf interface
Which CLI command is used to see the current OSPF link－state database?() A. show ospf databaseB. show ospf neighborC. show protocols ospfD. show ospf link-state
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B. When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E. None of the other answers is correct.
Refer to the exhibit. Which two Cisco IOS commands on R2 would verify its OSPF neighbor relationships?() A.show ip ospfB.show ip ospf interfaceC.show ip ospf neighborD.show ip ospf databaseE.show ip ospf statisticsF.show running - config begin router ospf
The administrator wants to verify the current state of the OSPF database loading process. Which show command should the administrator use?() A. show ip ospf [process - id] interfaceB. show ip ospf neighborC. show ip ospf [process - id]D. show ip ospf [process - id area - id] database
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
The Dev － 1 and Dev －3 routers are OSPF neighbors over the Ethernet 0／0 connection. Based on the show ip ospf neighbor output from the Dev － 1 and Dev － 3 routers, which statement is true?() A. Dev - 1 is the DR because it has a lower OSPF router IDB. Dev - 3 is the DR because it has a higher OSPF router priorityC. Both Dev - 1 and Dev - 3 are using the def ault OSPF router priorityD. Dev - 3 is the DR because it has a lower OSPF router IDE. Dev - 1 is the DR because it has a higher OSPF router priority
Which one of the following privileged EXEC mode IOS show commands will display the state of the OSPF DR／BDR (designated router ／ backup designated router) election process?() A. TK1# show ip ospf interfaceB. TK1# show ip ospf priorityC. TK1# show ospf neighbor detailD. TK1# show ospf processesE. TK1# show ospf neighbor state
可以使用_____命令查看生存周期和序列号？A.show ip ospfB.show ip ospf neighborC.show ip ospf databaseD.show ip route ospf
要确定区域内放置的接口是否正确，应使用下列哪一个命令？（）A、show ip ospfB、show ospf interfaceC、show ip interfaceD、show ip ospf interfaceE、show interface
当网络ospf出现邻居down告警，cisco设备哪个命令能列出与邻居路由器邻接状态（）A、debug ospf eventsB、show ip ospf border-routersC、show ip ospf neighborD、show ip ospf database
查看7750SROSPF邻居关系是否建立使用以下哪个命令（）A、show ospfB、show ospf neighborC、show router ospfD、show router ospf neighbor
查看7750SR设备OSPF下接口状态命令为（）A、shwo router ospfinterfaceB、show router interfaceC、show router ospfD、show router ospfneighbor
哪个命令能列出与邻居路由器邻接状态（）A、debug ospf eventsB、show ip ospf border-routersC、show ip ospf neighborD、show ip ospf database
The administrator wants to verify the current state of the OSPF database loading process. Which show command should the administrator use?（）A、show ip ospf [process - id] interfaceB、show ip ospf neighborC、show ip ospf [process - id]D、show ip ospf [process - id area - id] database
Which of the following commands will display the name of the IOS image file being used in a Cisco router?（）A、Router# show IOSB、Router# show versionC、Router# show imageD、Router# show protocolsE、Router# show flash
查看OSPF路由器的邻居列表，应使用下列哪个命令？（）A、show ip ospf neighborB、show ip ospf interfaceC、show ip ospfD、show ip route
Which one of the following privileged EXEC mode IOS show commands will display the state of the OSPF DR/BDR (designated router / backup designated router) election process?（）A、TK1# show ip ospf interfaceB、TK1# show ip ospf priorityC、TK1# show ospf neighbor detailD、TK1# show ospf processesE、TK1# show ospf neighbor state
下面哪个命令可以查看OSPFV3路由接口信息（）A、show ipov6 ospf neighborB、show ipv6 ospf interfaceC、show ipv6 ospf catabase
管理员想在MSR路由器上配置OSPF路由优先级值为60，则下列哪条命令是正确的？（）A、[Router]ospf preference 60B、[Router]preference 60C、[Router-ospf-1]ospf preference 60D、[Router-ospf-1]preference 60
输入哪条命令可以看到以下信息？（） LS DataBase Type :Router Ls id :10.1.2.2 Ady rtr :1050 Len :72 Seq# :80000008 Cksum (DC) Area Border Router Link count 4 Link id :192.168.2.1 Data :255.255.255.255 Metric:1562 Link id :10.1.2.2 Data :10.1.3.1 Type :Router Metric :1562 Link id :10.1.3.2 Data :255.255.255.255 Type :StubNet Metric :1562 A、 show ip route B、 show ip ospf isa C、 show ip ospf database D、 show ip ospf interface
（）命令查看一些接口的信息，包括接口的花费、状态、类型、优先级等A、show ip ospfB、show ip ospferrorC、show ip ospf interfaceD、show ip ospf enighbor
Which command would display OSPF parameters such as filters， default metric， maximum paths，and number of areas configured on a router？（）A、show ip protocolB、show ip routeC、show ip ospf interfaceD、show ip ospfE、show ip interfaceF、None of the other alternatives apply
Which CLI command is used to see the current OSPF link-state database?（）A、show ospf databaseB、show ospf neighborC、show protocols ospfD、show ospf link-state
Which CLI command displays all OSPF LSAs received by the local router？（）A、show ospf neighborB、show ospf databaseC、show ospf interfaceD、show ospf adjacency