设置电源通电自启动需将（）设置为ON。A、Power Button ModeB、RI ResumeC、AC Power Loss RestartD、RTC Resume
设置电源通电自启动需将（）设置为ON。
- A、Power Button Mode
- B、RI Resume
- C、AC Power Loss Restart
- D、RTC Resume
相关考题：
如果当前控制器电源状态为active,哪个操作能让其变为standby模式?() A.Push the power button for a minimum of 6 seconds, then releaseB.Push the power button for a minimum of 8 seconds, then releaseC.Push the power button for a minimum of 4 seconds, then releaseD.Push the power button for a minimum of 2 seconds, then release
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre－amp is needed at Site B to (). (Choose three.) A. offset the OADM loss at site bB. overcome the high multiplexer loss at site aC. amplify signal levels after the high loss through Fiber Span 1D. adjust add channels at site B to be at the same level as the passthrough channelsE. ensure that the per channel power is higher than the minimum needed for the post-amp at Site b
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? （）(Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.)A.15dBB.17dBC.21dBD.26dBE.27dB
UE根据以下哪个公式来进行估算PRACH的初始发射功率:() A.Preamble_Initial_Power=UL_Path_Loss+UL_interference+ConstantValueB.Preamble_Initial_Power=DL_Path_Loss+UL_interference+ConstantValueC.Preamble_Initial_Power=UL_Path_Loss+UL_interference+DefaultConstantValueD.Preamble_Initial_Power=DL_Path_Loss+UL_interference+DefaultConstantValue
在Advanced下的（）可显示计算机电源输出的各类电压和CPU核心电压。A、Voltage MonitorB、Hardware Health ConfigurationC、Power Button ModeD、RI Resume
在Advanced下的（）可显示计算机内风扇的转速和CPU温度。A、Voltage MonitorB、Power Button ModeC、Hardware Health ConfigurationD、RI Resume
基站EIRP的计算公式为（）A、BTS max. transmit power －BTS combiner and jumper loss －BTS feeder and connector loss + BTS antenna gainB、BTS max. transmit power －BTS combiner and jumper lossC、BTS combiner and jumper loss －BTS feeder and connector lossD、以上都不对
PhoenixBIOS主板加电时（插入电源线）电源灯会亮5s左右，风扇（电源风扇、系统风扇、CPU风扇）转3s左右，光驱灯亮2s左右。这种情况如何处理（）A、刷新知识库最新BIOS解决B、按DEL进入主板BIOS，把Power选项中的After Power Loss（BIOS默认设置为Last State）设置为Stay Off即可C、无需调整，正常情况D、更换替换型号主板
如果（）参数设置过低，AN可能需要发送更多的接入探测，从而导致接入信道负载增加，发生碰撞的概率增大。A、Open Loop Power AdjustmentB、Initial Probe Power Correction FactorC、PowerIncrementStepD、Initial Power Control Thresholdfor Reverse Outer Loop
A power loss during a firmware update would MOST likely result in which of the following?（）A、Increased heat outputB、Damage of the hardwareC、Loss of storage dataD、Decreased performance
Which system provides the highest performance per core, and the least cost for applications licensed per core?（）A、A Power 795 with MaxCore modeB、A Power 780 with MaxCore modeC、A Power 755 with TurboCore modeD、A Power 780 with TurboCore mode
电源系统是如何向“28V DC HOT BAT BUS”提供电源的？（）A、将驾驶舱头顶P5-13面板上的“BAT”电门设置到“BAT”位置B、将驾驶舱头顶P5-5面板上的“STAND BY POWER”电门设置到“AUTO”位置C、将驾驶舱头顶P5-5面板上的“STAND BY POWER”电门设置到“BAT”位置D、电瓶直接与“28VDCHOTBATBUS”相连接
飞控系统在什么状态下进行POWER-UP BIT？（） A、任何时候都可以B、只有当飞机接通AC时，系统才开始POWER-UP BITC、系统不必进行POWER-UP BITD、接通地面勤务电源时
交流不间断电源UPS的英文称为（）。A、UNINTERRUPTIBLE POWER SUPPLYB、UNINTERRUPTIBLE POWER SUPERC、UNCHANGEABLY POWER SUPPLYD、UNCHANGEABLY POWER SUPER
单选题When the current in a power transmission line is increased, the power loss （）Aincreases as the square of the currentBdecreases as the square root of the currentCremains the same, as it is independent of current flowDincreases in direct proportion as the current
单选题（） shall be continuously powered and shall have an automatic changeover to a stand by power supply in case of loss of normal power supply.ACooling systemBAlarm systemCThe air conditioning installationDThe mooring equipment