The command "ip route 192.168.24.64 255.255.255.192 192.168.8.2 100" was configured on a router named TK1. No routing protocols or other static routes are configured on the Corporate router yet.Based on this information, which statement is true about this command?（）A、This command sets a gateway of last resort for the TK1 router.B、The number 100 indicates the number of hops to the destination network.C、The interface with IP address 192.168.8.2 is on the TK1 router.D、The command creates a static route for all IP traffic with the source address 192.168.24.64.E、Packets destined for host 192.168.24.124 will be sent to 192.168.8.2.F、None of the above
The command "ip route 192.168.24.64 255.255.255.192 192.168.8.2 100" was configured on a router named TK1. No routing protocols or other static routes are configured on the Corporate router yet.Based on this information, which statement is true about this command?（）
- A、This command sets a gateway of last resort for the TK1 router.
- B、The number 100 indicates the number of hops to the destination network.
- C、The interface with IP address 192.168.8.2 is on the TK1 router.
- D、The command creates a static route for all IP traffic with the source address 192.168.24.64.
- E、Packets destined for host 192.168.24.124 will be sent to 192.168.8.2.
- F、None of the above
相关考题：
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）A. Subnet numberB. Next - hop router IP address of the routeC. Whether the route is an E1 or E2 routeD. The ro ute‘s tagE. The number of router hops between the router and the subnet
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?() A. The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB. The router must hav e at least one working link connected to each routing domainC. The redistribute command must be configured under EIGRP to send the routes to OSPFD. The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: Gateway of last resort is 1.1.1.1 to network 2.0.0.0.Whic h of the following is most likely to have caused this output to occur on R1?（）A. R1 has been configured with an ip default- network 2.0.0.0 command.B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D. Another router has been configured with an ip default - network 2.0.0.0 command.E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
Refer to the exhibit. Which statement about dynamic routing protocols for this network is true? () A.No dynamic interior routing protocol can summarize as shownB.Unless configured otherwise, EIGRP would automatically summa rize the prefixes as shown in the exhibitC.With this IP addressing scheme, EIGRP can be manually configured to summarize prefixes at the specified summarization pointsD.The IP address design lends itself to OSPF Each summarizing router would be an ABR, summarizing to the next area in the address hierarchy
A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?（）A. The router will use the static route.B. The router will use the OSPF route.C. The route will use the EIGRP route.D. The router will load balance and use all three routes.
The command "ip route 192.168.24.64 255.255.255.192 192.168.8.2 100" was configured on a router named TK1. No routing protocols or other static routes are configured on the Corporate router yet.Based on this information, which statement is true about this command?（）A. This command sets a gateway of last resort for the TK1 router.B. The number 100 indicates the number of hops to the destination network.C. The interface with IP address 192.168.8.2 is on the TK1 router.D. The command creates a static route for all IP traffic with the source address 192.168.24.64.E. Packets destined for host 192.168.24.124 will be sent to 192.168.8.2.F. None of the above
You have just configured a static default route on router TK1. What is the purpose of a default route?() A. It is a route to be used when the routing protocol fails.B. It is a route configured by an ISP that sends traffic into a corporate network.C. It is a route used when a packet is destined for a remote network that is not listed in the routing table.D. It is a route manually configured for a specific remote network for which a routing protocol is not configured.E. It is used to send traffic to a stub network.
Which three statements are true about EIGRP route summarization?() A.When manual summarization is configured, the router immediately creates a route that points to null0 interfaceB.Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routingC.Manual route summarization is configured on the interfaceD.The ip summary - address eigrp command generates a default route with an administrative distance of 5E.When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routesF.The ip summary - address eigrp command generates a default route with an administrative distance of 90
A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。A.The router will use the static route.B.The router will use the OSPF route.C.The router will use the EIGRP route.D.The router will load balance and use all three routes.
Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4?() A.It establishes a static route to the 172.16.3.0 network.B.It establishes a static route to the 192.168.2.0 network.C.It configures the router to send any traffic for an unknown destination to the 172.16.3.0 network.D.It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4.E.It uses the default administrative distance.F.It is a route that would be used last if other routes to the same destination exist.
Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4 (Choose two.)（）。A、It establishes a static route to the 172.16.3.0 networkB、It establishes a static route to the 192.168.2.0 networkC、It configures the router to send any traffic for an unknown destination to the 172.16.3.0 networkD、It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4E、It uses the default administrative distanceF、It is a route that would be used last if other routes to the same destination exist
A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。A、The router will use the static route.B、The router will use the OSPF route.C、The router will use the EIGRP route.D、The router will load balance and use all three routes.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A、Subnet numberB、Next - hop router IP address of the routeC、Whether the route is an E1 or E2 routeD、The ro ute's tagE、The number of router hops between the router and the subnet
Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4? (Choose two.)（）A、It establishes a static route to the 172.16.3.0 network.B、It establishes a static route to the 192.168.2.0 network.C、It configures the router to send any traffic for an unknown destination to the 172.16.3.0 network.D、It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4.E、It uses the default administrative distance.F、It is a route that would be used last if other routes to the same destination exist.
Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Router R1 lists 4 routes for subnet 10.1.1.0/24 in the output of the show ip eigrp topology all - links command. The variance 200 command is configured, but no other related commands are configured. Which of the following rules are true regarding R1's decision of what r outes to add to the IP routing table? Note that RD refers to reported distance and FD to feasible distanc E.（）A、Adds all routes for which the metric is = 200 * the best metric among all routesB、Adds all routes because of the ridiculously high variance settingC、Adds all successor and feasible successor routesD、Adds all successor and feasible successor routes for which the metric is=200 * the best metric among all routes
Which three statements are true about EIGRP route summarization?（）A、When manual summarization is configured, the router immediately creates a route that points to null0 interfaceB、Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routingC、Manual route summarization is configured on the interfaceD、The ip summary - address eigrp command generates a default route with an administrative distance of 5E、When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routesF、The ip summary - address eigrp command generates a default route with an administrative distance of 90
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB、The router must hav e at least one working link connected to each routing domainC、The redistribute command must be configured under EIGRP to send the routes to OSPFD、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
多选题Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4 (Choose two.)（）。AIt establishes a static route to the 172.16.3.0 networkBIt establishes a static route to the 192.168.2.0 networkCIt configures the router to send any traffic for an unknown destination to the 172.16.3.0 networkDIt configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4EIt uses the default administrative distanceFIt is a route that would be used last if other routes to the same destination exist
单选题The command "ip route 192.168.24.64 255.255.255.192 192.168.8.2 100" was configured on a router named TK1. No routing protocols or other static routes are configured on the Corporate router yet.Based on this information, which statement is true about this command?（）AThis command sets a gateway of last resort for the TK1 router.BThe number 100 indicates the number of hops to the destination network.CThe interface with IP address 192.168.8.2 is on the TK1 router.DThe command creates a static route for all IP traffic with the source address 192.168.24.64.EPackets destined for host 192.168.24.124 will be sent to 192.168.8.2.FNone of the above
单选题A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。AThe router will use the static route.BThe router will use the OSPF route.CThe router will use the EIGRP route.DThe router will load balance and use all three routes.
单选题You have just configured a static default route on router TK1. What is the purpose of a default route?（）AIt is a route to be used when the routing protocol fails.BIt is a route configured by an ISP that sends traffic into a corporate network.CIt is a route used when a packet is destined for a remote network that is not listed in the routing table.DIt is a route manually configured for a specific remote network for which a routing protocol is not configured.EIt is used to send traffic to a stub network.
单选题Which statement about the use of Route Target Rewrite is true？（）AIt is mainly used in Intra-AS MPLS VPLS deployments and is configured at the ASBR to avoid misconfiguration of the Route Target assignment for VPN configurationsBIt is mainly used in Inter-AS MPLS VPN deployments and is configured at the ASBR to avoid misconfiguration of the Route Target assignment for VPN configurationsCIt is mainly used in Intra-AS MPLS VPLS deployments and is configured at the Router Reflectorto avoid misconfiguration in Route Target assignment for VPN configurationsDIt is mainly used in Inter-AS MPLS VPLS deployments and is configured at the Router Reflectorto avoid misconfiguration of the Route Target assignment for VPN configurationsEIt is mainly used in Inter-AS MPLS VPLS deployments and is configured at the PE router to avoid to misconfiguration of the Route Target assignment for VPN configurations
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router
单选题A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?（）AThe router will use the static route.BThe router will use the OSPF route.CThe route will use the EIGRP route.DThe router will load balance and use all three routes.
多选题Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4? (Choose two.)（）AIt establishes a static route to the 172.16.3.0 network.BIt establishes a static route to the 192.168.2.0 network.CIt configures the router to send any traffic for an unknown destination to the 172.16.3.0 network.DIt configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4.EIt uses the default administrative distance.FIt is a route that would be used last if other routes to the same destination exist.
单选题Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）ASubnet numberBNext - hop router IP address of the routeCWhether the route is an E1 or E2 routeDThe ro ute's tagEThe number of router hops between the router and the subnet