Which interconnect topology is supported for pSeries cluster solutions with Cluster Systems Manager？（）A、ATMB、EthernetC、SP Switch2D、Fibre Channel
Which interconnect topology is supported for pSeries cluster solutions with Cluster Systems Manager？（）
- A、ATM
- B、Ethernet
- C、SP Switch2
- D、Fibre Channel
相关考题：
Which of the following wiring standards would MOST likely be used to interconnect two devices without the use of a hub or switch?() A.568AB.568BC.CrossoverD.Loopback
TestKing has five regional offices that are located in different cities. The IT staff is evaluating WAN technologies to interconnect the regional offices to corporate headquarters. Each of the regional offices should be connected to the corporate headquarters in a hub and spoke arrangement using a packet-switched technology.Which of the following WAN technologies will fulfill these requirements?（）A. Frame RelayB. ISDNC. T1 leased linesD. Wireless
Which two factors determine the recommended maximum number of virtual interfaces on a Cisco UCSsystem?（）A、the number of computer blades in the systemB、the number of interfaces sharing the uplinksC、the driver version on the OS running on the computer bladeD、the number of uplinks between I/O Module and Fabric Interconnect
Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）A、LACPB、PAgPC、MCPC
Which statement ab0ut VLANs in a Cisco UCS is true?（）A、Fabric interconnect can never participate in VTPB、Fabric interconnect supports ISL and 802.1Q trunkingC、The supported range of VLANs is auto-configured by UCSD、VLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
What is the use of an "all configuration" backup in Cisco UCS？（）A、 Can be used to migrate from a 6120 to a 6140 and retain the same service profilesB、 Can only be used on the fabric interconnect on which it was createdC、 Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster informationD、 Can be used to match firmware versions between 6120 and 6140 during a migration
Which three functions can CCC be used for？（）A、To interconnect VLANSB、To interconnect ATM VCsC、To interconnect MPLS LSPsD、To interconnect MPLS VPNs
TestKing has five regional offices that are located in different cities. The IT staff is evaluating WAN technologies to interconnect the regional offices to corporate headquarters. Each of the regional offices should be connected to the corporate headquarters in a hub and spoke arrangement using a packet-switched technology. Which of the following WAN technologies will fulfill these requirements?（）A、Frame RelayB、ISDNC、T1 leased linesD、Wireless
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）A、 Uplink Ethernet ports or border portsB、 Appliance portsC、 Server portsD、 Fabric portsE、 Backplane portsF、 vEth interfacesG、 A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
Which statements are true regarding the Cisco UCS fabric failover feature？ （）A、 FabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.B、 Gratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover. C、 Fabric failover can be used on vNICs and vHBAs.D、 Fabric failover is configured as part of the service profile.E、 Fabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
The Cisco 6100 XP Fabric Interconnect is available in Which two configurations?（）A、20 port+expansion moduleB、24 port+expansion moduleC、40 port+expansion moduleD、48 port+expansion module
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）A、 The fabric interconnect is in the end-host mode， and all uplink ports have failed.B、 The server port to which the adapter is pinned has failed.C、 A transient error has caused the link to fail.D、 The fabric interconnect is in the switch mode， and all uplink ports have failed.E、 The link for a network-facing host interface is missing.
Which bays do the Multi-Switch Interconnect Module populate? （）A、3 and 4 B、3, 4, 5, and 6 C、7 and 9 D、7, 8, 9, and 10
A customer asks which bays they could install Multi-Switch Interconnect Module (MSIM). Which of the following is the source of this information?（）A、CDAT B、IBM Systems Director C、Tivoli Provisioning Manager (TPM) D、BladeCenter Interoperability guide
A customer asks which bays they could install Multi-Switch Interconnect Module （MSIM）. Which is the source of this information of the following？（）A、CDATB、IBM Systems DirectorC、Tivoli Provisioning Manager （TPM）D、xREF
多选题Which two factors determine the recommended maximum number of virtual interfaces on a Cisco UCSsystem?（）Athe number of computer blades in the systemBthe number of interfaces sharing the uplinksCthe driver version on the OS running on the computer bladeDthe number of uplinks between I/O Module and Fabric Interconnect
多选题Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）AThe fabric interconnect is in the end-host mode， and all uplink ports have failed.BThe server port to which the adapter is pinned has failed.CA transient error has caused the link to fail.DThe fabric interconnect is in the switch mode， and all uplink ports have failed.EThe link for a network-facing host interface is missing.
多选题Which three functions can CCC be used for？（）ATo interconnect VLANSBTo interconnect ATM VCsCTo interconnect MPLS LSPsDTo interconnect MPLS VPNs
多选题Which statements are true regarding the Cisco UCS fabric failover feature？ （）AFabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.BGratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover.CFabric failover can be used on vNICs and vHBAs.DFabric failover is configured as part of the service profile.EFabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
单选题Which statement ab0ut VLANs in a Cisco UCS is true?（）AFabric interconnect can never participate in VTPBFabric interconnect supports ISL and 802.1Q trunkingCThe supported range of VLANs is auto-configured by UCSDVLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
单选题What is the use of an "all configuration" backup in Cisco UCS？（）A Can be used to migrate from a 6120 to a 6140 and retain the same service profilesB Can only be used on the fabric interconnect on which it was createdC Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster informationD Can be used to match firmware versions between 6120 and 6140 during a migration
单选题Which interconnect is used on the storage side of the SONAS storage node to provide highperformance?（）A6 Gbps SAS BFibre Channel C10 Gb Ethernet DInfiniBand (IB)
单选题Which of the following wiring standards would MOST likely be used to interconnect two devices without the use of a hub or switch?（）A568AB568BCCrossoverDLoopback
单选题Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）ALACPBPAgPCMCPC
多选题The Cisco 6100 XP Fabric Interconnect is available in Which two configurations?（）A20 port+expansion moduleB24 port+expansion moduleC40 port+expansion moduleD48 port+expansion module
单选题Which bays do the Multi-Switch Interconnect Module populate? （）A3 and 4 B3, 4, 5, and 6 C7 and 9 D7, 8, 9, and 10
多选题A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）AUplink Ethernet ports or border portsBAppliance portsCServer portsDFabric portsEBackplane portsFvEth interfacesGA Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.