单选题After ensuring that the （） is correct the bearing clearance should be checked.AnapBgapCnipDdeflection
单选题
After ensuring that the （） is correct the bearing clearance should be checked.
A
nap
B
gap
C
nip
D
deflection
参考解析
解析：
暂无解析
相关考题：
The correct procedure for giving an auxiliary boiler a bottom blow, is to begin .A.when the boiler has been secured long enough for most solids to settleB.when the boiler has been cooled to ambient temperatureC.only after raising the water level to within 0.5 inch of the high water cutout onlyD.after bypassing the low pressure
The most crucial time for any bearing with regards to lubrication isA.during low loadsB.after proper oil viscosity is reachedC.during startingD.after cleaning filters
Adjust ______by means of lead wire.A.the clearance of the main bearingB.the diameter of main bearingC.the gap of main bearingD.the tolerance of main bearing
Which of these is a correct description of SSO?（）A、It will only become active after a software failure.B、It will only become active after a hardware failure.C、It requires that Cisco NSF be enabled in order to work successfully.D、It synchronizes the MAC, FIB, and adjacency tables between Active and Standby Route Processors.
Which of these is a correct description of SSO？（）A、 It will only become active after a software failure.B、 It will only become active after a hardware failure.C、 It requires that Cisco NSF be enabled in order to work successfully.D、 It synchronizes the MAC·， FIB·， and adjacency tables between Active and Standby RouteProcessors.
After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）A、B、#C、?D、*E、All of the aboveF、None of the above
Which of these is a correct description of Stateful Switchover？（）A、 It will only become active after a software failureB、 It will only become active after a hardware failureC、 It requires that Cisco N3F· be enabled in order to work successfullyD、 It synchronizes the MAC·， FIB·， and adjacency tables between Active and Standby Route Processors
A user reports that printed pages are smearing after the pages come out of a laser printer. Which of the following is the MOST likely problem?（）A、The corona wire is not supplying the correct voltage.B、The fuser is not reaching the correct temperature.C、The paper is card stock and is too thick.D、The paper has a humidity content that is too low.
A system administrator decides to review the system error log after installing new hardware. Which of the following is the correct command to use？（）A、errptB、syslogC、prtdiagD、errlogger
单选题After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）AB#C?D*EAll of the aboveFNone of the above
单选题As to the bearing, of the following, which statement is not true?（）Aff overheat is found, the engine must be stopped for inspectionBMuch heat of the crankcase door indicates that the bearing is overheatedCIf bearing clearance is too large, knocking will be heard in the crankcaseDIf bearing clearance is too large or too small, the white metal may be melted
单选题Shims of different thicknesses are inserted between the shells to enable adjustment of （）.Athe bearing clearancesBthe bearing thicknessCthe bearing strengthDthe bridge hardness
单选题An acceptable means of tightening connecting rod and main bearing cap bolts is to measure the （） Ⅰ.torque applied to each nut and bolt assembly Ⅱstretch of each nut before and after tighteningAⅠonlyBⅡ onlyCboth Ⅰ and ⅡDneither Ⅰ nor Ⅱ
单选题A distance piece, with ground faces, may be interposed between the rod and the bearing housing, its thickness being chosen to ensure the correct （）.Aexpansion ratioBpressure ratioCcompression ratioDclearance ratio
单选题An acceptable method of measuring for the correct rotational force applied to the connecting rod and main bearing bolts, is to use a（）Atorque wrenchBmonkey wrenchCpipe wrenchDslugging wrench
单选题Measure （） by means of lead wire.Athe clearance of the main bearingBthe play of the miler bearingCthe gap of the main bearingDthe tolerance of the main bearing
单选题In a large, low-speed diesel engine the clearance between the piston crown and cylinder head is found to be excessiveIn order to correct for this, you should（）Abuild up the piston crown by metal sprayingBbuild up the cylinder head by metal sprayingCinsert shims between the crankpin bearing box and the connecting rod footDinstall a thinner head gasket
单选题A distance piece, with ground faces, known as a compression plate, may be interposed between the rod and the beating housing, its thickness being chosen to ensure the correct （）.Acompression pressureBcompression testCcompression ratioDcompression clearance
单选题Which of these is a correct description of SSO？（）A It will only become active after a software failure.B It will only become active after a hardware failure.C It requires that Cisco NSF be enabled in order to work successfully.D It synchronizes the MAC·， FIB·， and adjacency tables between Active and Standby RouteProcessors.
单选题Please draw out a 0l mm shim between the two halves of the bearing （） the clearance.Ato reduceBto increaseCand reduceDand increase
单选题Please draw out a 01 mm （） between the two halves of the bearing to reduce the clearance.AshimBgasketCwasherDpacking
单选题When used with reversing reduction gears, medium-speed diesel engines should be bolted to their foundations with fitted bolts at the drive end and clearance(loosely fitted) bolts in other locations √This is done to （）Amaintain alignment when the ship’s hull is working in heavy seasBensure engine vibrations correspond to the natural frequency of the hullCpermit the engine to expand away from the driven equipment as the engine heats up and expandsDmaintain engine thrust bearing clearances
单选题The bearing cap and shell are replaced and tightened up until （）.Athe “ nip ”is zeroBthe “ nap ” is zeroCthe “ gap ”is correctDthe “ clearance ” is correct
单选题The insertion of shims between the foot of a marine type connecting rod and a bearing box would result in （）Aincreased compression ratioBdecreased compression ratioCincreased bearing clearanceDdecreased bearing clearance
单选题To determine the main bearing clearance of a propulsion diesel engine, you should measure the main bearing shell using a ball anvil outside micrometer and measure the crankshaft journal using a/an （）AtelescopingBring ‘snap’ gaugeCinside vernier caliperDoutside micrometer
单选题Lubricating oil used in a diesel engine serves to（）Areduce the wear of bearing surfacesBcool the bearing surfacesCassist in sealing bearing surfacesDall of the above
单选题The shells are secured by means of bearing caps and studs, the necessary clearance being provided by means of （） of different thickness.AshimsBpackingCglandsDwashers