多选题Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?（）ASummarize data center subnets.BUse passive interfaces to ensure appropriate adjacencies.CTune the EIGRP timers to enable EIGRP to achieve quicker convergence.DAdjust the default bandwidth value to ensure proper bandwidth on all links.EAdvertise a default summary route into the data center core from the aggregation layer.
多选题
Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?（）
A
Summarize data center subnets.
B
Use passive interfaces to ensure appropriate adjacencies.
C
Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.
D
Adjust the default bandwidth value to ensure proper bandwidth on all links.
E
Advertise a default summary route into the data center core from the aggregation layer.
参考解析
解析：
暂无解析
相关考题：
A network design shows that R1 has four different possible paths from itself to the Data Center subnets.Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）A. show ip eigrp topologyB. show ip eigrp topology all - linksC. show ip route eigrpD. show ip route eigrp all - linksE. show ip eigrp topology all - learned
Your network consists of a large hub － and － spoke Frame Relay network with a CIR of 56 kb／s foreach spoke. Which statement about the selection of a dynamic protocol is true?() A. EIGRP would be appropriate if LMI type ANS I is NOT used.B. EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas.C. EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.
When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful.What is the next thing that should be checked?（）A. Verify that the EIGRP hello and hold timers match exactly.B. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.C. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.D. Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.
Which of the following settings could prevent two potential EIGRP neighbors from becoming neighbors?() A. The i nterface used by one router to connect to the other router is passive in the EIGRP process.B. Duplicate EIGRP router IDs.C. Mismatched Hold Timers.D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.
What parameters must you specify when you enable EIGRP routing?() A. The broadcast address, and AS numberB. The network number and AS numberC. EIGRP routing, network number and passive interfaceD. EIGRP routing, network number, and AS
Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?() A. Summarize data center subnets.B. Use passive interfaces to ensure appropriate adjacencies.C. Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.D. Adjust the default bandwidth value to ensure proper bandwidth on all links.E. Advertise a default summary route into the data center core from the aggregation layer.
Which two design recommendations are most appropriate when OSPF is the data center core routing protocol? () A. Never use passive interfaces.B. Use NSSA areas from the core down.C. Use totally stub areas to stop type 3 LSAs.D. Use the lowest Ethernet interface IP address as the router ID.E. Tune OSPF timers to enable OSPF to achieve quicker convergence.
Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?（）A、Summarize data center subnets.B、Use passive interfaces to ensure appropriate adjacencies.C、Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.D、Adjust the default bandwidth value to ensure proper bandwidth on all links.E、Advertise a default summary route into the data center core from the aggregation layer.
When EIGRP is used as the PE-CE routing protocol which of these statements is correct?（）A、EIGRP can be used only as the PE-CE routing protocol if the PE and CE routers are in the same ASB、Other EIGRP AS routes are automatically advertised to the CE router and do not require a redistribution configuration command to be configuredC、Unlike other routing protocols that are used between PE and CE routers, EIGRP supports backdoor linksD、Configure of the VPN is only required on the PE router
Which of the following is true regarding the effect of EIGRP queries on the network design？（）A、 EIGRP queries will be the most significant issue with respect to stability and convergence B、 EIGRP queries are not a consideration as long as EIGRP has a feasible successor with a nexthop AD that is greater than the FD of the current successor route C、 EIGRP queries will only increase the convergence time when there are no EIGRP stubsdesigned in the network
What parameters must you specify when you enable EIGRP routing?（）A、The broadcast address, and AS numberB、The network number and AS numberC、EIGRP routing, network number and passive interfaceD、EIGRP routing, network number, and AS
You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.D、There is no network statement configuration in EIGRP for IPv6.E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive
Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）A、 Summarize data center subnets.B、 Use passive interfaces to ensure appropriate adjacencies.C、 Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.D、 Adjust the default bandwidth value to ensure proper bandwidth on all links.E、 Advertise a default summary route into the data center core from the aggregation layer.
Which two design recommendations are most appropriate when OSPF is the data center core routing protocol？ （）A、 Never use passive interfaces.B、 Use NSSA areas from the core down.C、 Use totally stub areas to stop type 3 LSAs.D、 Use the lowest Ethernet interface IP address as the router ID.E、 Tune OSPF timers to enable OSPF to achieve quicker convergence
Which of the following are not BGRP data structures？ （Choose all that apply.）（）A、EIGRP database tableB、EIGRP CEF tableC、EIGRP neighbor tableD、EIGRP adjacency tableE、EIGRP interface tableF、EIGRP topology table
Which three statements about EIGRP are true?（）A、EIGRP converges fast RIP because of DUAL and backup routes that are stored in the topology table.B、EIGRP uses a hello protocol to establish neighbor relationshipsC、EIGRP uses split horizon and reverse poisoning to avoid routing loops.D、EIGRP uses periodic updates to exchange routing informationE、EIGRP allows routers of different manufacturers to interoperateF、EIGRP supports VLSM and authentication for routing updates.G、EIGRP use a broadcast address to send routing information.
Which two steps below should you perform on the hub router while configuring EIGRP routing over DMVPN （mGRE tunnel）？ （）A、Set the NHRP hold time to match the EIGRP hold timeB、Add the enable eigrp stub commandC、Add the disable eigrp as-member split-horizon commandD、Add the disable eigrp as-member next-hop-self command
A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）A、show ip eigrp topologyB、show ip eigrp topology all - linksC、show ip route eigrpD、show ip route eigrp all - linksE、show ip eigrp topology all - learned
多选题Which of the following settings could prevent two potential EIGRP neighbors from becoming neighbors?（）AThe i nterface used by one router to connect to the other router is passive in the EIGRP process.BDuplicate EIGRP router IDs.CMismatched Hold Timers.DIP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.
多选题Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）ASummarize data center subnets.BUse passive interfaces to ensure appropriate adjacencies.CTune the EIGRP timers to enable EIGRP to achieve quicker convergence.DAdjust the default bandwidth value to ensure proper bandwidth on all links.EAdvertise a default summary route into the data center core from the aggregation layer.
单选题What parameters must you specify when you enable EIGRP routing?（）AThe broadcast address, and AS numberBThe network number and AS numberCEIGRP routing, network number and passive interfaceDEIGRP routing, network number, and AS
多选题Which two design recommendations are most appropriate when OSPF is the data center core routing protocol? （）ANever use passive interfaces.BUse NSSA areas from the core down.CUse totally stub areas to stop type 3 LSAs.DUse the lowest Ethernet interface IP address as the router ID.ETune OSPF timers to enable OSPF to achieve quicker convergence.
单选题When EIGRP is used as the PE-CE routing protocol which of these statements is correct?（）AEIGRP can be used only as the PE-CE routing protocol if the PE and CE routers are in the same ASBOther EIGRP AS routes are automatically advertised to the CE router and do not require a redistribution configuration command to be configuredCUnlike other routing protocols that are used between PE and CE routers, EIGRP supports backdoor linksDConfigure of the VPN is only required on the PE router
多选题Which two steps below should you perform on the hub router while configuring EIGRP routing over DMVPN （mGRE tunnel）？ （）ASet the NHRP hold time to match the EIGRP hold timeBAdd the enable eigrp stub commandCAdd the disable eigrp as-member split-horizon commandDAdd the disable eigrp as-member next-hop-self command
多选题How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)（）。AIf RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.BIf RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.CIf EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.DIf EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.EIf EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.FIf EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
单选题Which of the following is true regarding the effect of EIGRP queries on the network design？（）A EIGRP queries will be the most significant issue with respect to stability and convergence B EIGRP queries are not a consideration as long as EIGRP has a feasible successor with a nexthop AD that is greater than the FD of the current successor route C EIGRP queries will only increase the convergence time when there are no EIGRP stubsdesigned in the network
单选题A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）Ashow ip eigrp topologyBshow ip eigrp topology all - linksCshow ip route eigrpDshow ip route eigrp all - linksEshow ip eigrp topology all - learned