多选题有关HSRP操作哪三种说法是正确的?()A虚拟IP地址和虚拟MA+ K44C地址是活跃的HSRP主路由器上。B该HSRP默认的计时器是3秒的hello间隔10秒失效时间。CHSRP仅支持明文验证。D该HSRP虚拟IP地址必须在不同的子网的路由器的同一个LAN接口上。E该HSRP虚拟IP地址必须是相同LAN上的路由器的接口地址之一。F最多HSRP支持255组每个接口,可实现负载均衡的管理形式。
多选题
有关HSRP操作哪三种说法是正确的?()
A
虚拟IP地址和虚拟MA+ K44C地址是活跃的HSRP主路由器上。
B
该HSRP默认的计时器是3秒的hello间隔10秒失效时间。
C
HSRP仅支持明文验证。
D
该HSRP虚拟IP地址必须在不同的子网的路由器的同一个LAN接口上。
E
该HSRP虚拟IP地址必须是相同LAN上的路由器的接口地址之一。
F
最多HSRP支持255组每个接口,可实现负载均衡的管理形式。
参考解析
解析:
暂无解析
相关考题:
有关HSRP操作哪三种说法是正确的?() A.虚拟IP地址和虚拟MA+K44C地址是活跃的HSRP主路由器上。B.该HSRP默认的计时器是3秒的hello间隔10秒失效时间。C.HSRP仅支持明文验证。D.该HSRP虚拟IP地址必须在不同的子网的路由器的同一个LAN接口上。E.该HSRP虚拟IP地址必须是相同LAN上的路由器的接口地址之一。F.最多HSRP支持255组每个接口,可实现负载均衡的管理形式。
有关Word的“撤消”操作,下列说法正确的是()A、“撤消”操作只能撤消本次操作,而对以前的操作无法撤消B、“撤消”操作只能撤消本次和上一次的操作C、可以进行多级的“撤消”操作D、以上都不正确
HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP? ()A、 HSRP provides redundancy and fault toleranceB、 HSRP allows one router to automatically assume the function of the second router if the second router failsC、 HSRP allows one router to automatically assume the function of the second router if the second router startsD、 HSRP provides redundancy and load balancing
有关HSRP操作哪三种说法是正确的?()A、虚拟IP地址和虚拟MA+ K44C地址是活跃的HSRP主路由器上。B、该HSRP默认的计时器是3秒的hello间隔10秒失效时间。C、HSRP仅支持明文验证。D、该HSRP虚拟IP地址必须在不同的子网的路由器的同一个LAN接口上。E、该HSRP虚拟IP地址必须是相同LAN上的路由器的接口地址之一。F、最多HSRP支持255组每个接口,可实现负载均衡的管理形式。
多选题Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol (HSRP)? ()ALoad sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.BRouters configured for HSRP can belong to multiple groups and multiple VLANs.CLoad sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.DAll routers configured for HSRP load balancing must be configured with the same priority.ERouters configured for HSRP must belong to only one group per HSRP interface.
多选题Which three statements best describe HSRP configuration on Cisco Nexus switches?()AIn a vPC topology, the primary HSRP router will respond to ARP requests, but both HSRP routers will forward data traffic. No additional configuration is required.BIn a vPC topology, the primary HSRP router will respond to ARP requests, but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.CYou can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.DYou can use the show standby command to verify HSRP operation and configuration.EIf you remove the feature hsrp command, all relevant HSRP configuration information isalso removed.