单选题Which of the following features should an administrator configure to allow an IDS to watch thetraffic on a switch?()AARP spoofingBVLANCMirroringDSpanning tree
单选题
Which of the following features should an administrator configure to allow an IDS to watch thetraffic on a switch?()
A
ARP spoofing
B
VLAN
C
Mirroring
D
Spanning tree
参考解析
解析:
暂无解析
相关考题:
Which of the following devices should an administrator connect to a protocol analyzer in order tocollect all of the traffic on a LAN segment?() A.HubB.VLANC.RouterD.Server
Which of the following technologies allows an administrator to submit traffic to an IDS for review?() A. Spanning treeB. VLANC. PoED. Port mirroring
An administrator is troubleshooting a communication issue between two computers on the sameLayer 2 switch.Which of the following is the BEST way to determine if the switch is causing the issue?() A. Setup an ACL that allows and logs all IP traffic between the two computersB. Configure a spanning tree to check for a loopC. Setup a span port on the switch to watch for CRC errorsD. Connect both computers using a crossover cable
Which of the following features should an administrator configure to allow an IDS to watch thetraffic on a switch?() A. ARP spoofingB. VLANC. MirroringD. Spanning tree
要在交换机上运行802.1w,可使用哪个命令来启用该协议?() A.Switch(config)#spanning-tree mode rapid-pvstB.Switch#spanning-tree mode rapid-pvstC.Switch(config)#spanning-tree mode 802.1wD.Switch#spanning-tree mode 802.1w
Which command enables RSTP on a switch?() A. spanning-tree mode rapid-pvstB. spanning-tree uplinkfastC. spanning-tree backbonefastD. spanning-tree mode mst
Which of the following three port types are valid Spanning Tree port types?(Choose the best threeanswers.)()A、Designated portB、Nonswitch portC、Switch portD、Nonroot portE、Nondesignated portF、Root port
Which of the following commands can be issued without interfering with the operation of loop guard?()A、Switch(config-if)#spanning-tree guard rootB、Switch(config-if)#spanning-tree portfastC、Switch(config-if)#switchport mode trunkD、Switch(config-if)#switchport mode access
A port in a redundant topology is currently in the blocking state and is not receiving BPDUs. To ensure that this port does not erroneously transition to the forwarding state, which command should be configured to satisfy the requirement?()A、Switch(config)#spanning-tree loopguard defaultB、Switch(config-if)#spanning-tree bdpufilterC、Switch(config)#udld aggressiveD、Switch(config-if)#spanning-tree bpduguard
Why would an administrator change the value of the spanning-tree priority of a switch?()A、in order to optimize the path that frames take from source to destinationB、to increase the priority so a designated port will become a root portC、to increase the BID, so the switch is more likely to become root bridgeD、in order to allow VLANs to be sent from one switch to another across a single linkE、to force a given switch to become an STP server
An administrator is troubleshooting a communication issue between two computers on the same Layer 2 switch. Which of the following is the BEST way to determine if the switch is causing the issue?()A、Setup an ACL that allows and logs all IP traffic between the two computersB、Configure a spanning tree to check for a loopC、Setup a span port on the switch to watch for CRC errorsD、Connect both computers using a crossover cable
Which three of the following network features are methods used to achieve high availability()A、Spanning Tree Protocol(STP)B、Delay reductionC、Hot Standby Routing Protocol(HSRP)D、Dynamic routing protocolsE、Quality of Service(QoS)F、Jitter management
VTP is configured on switch R1. Which of the following features were added in VTP version 2 that were not previously supported in VTP version 1?()A、Supports Token Ring VLANs.B、Allows VLAN consistency checks.C、Saves VLAN configuration memory.D、Reduces the amount of configuration necessary.E、Allows active redundant links when used with spanning tree.
Which command enables RSTP on a switch?()A、spanning-tree mode rapid-pvstB、spanning-tree uplinkfastC、spanning-tree backbonefastD、spanning-tree mode mst
A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?()A、The wrong cable type has been used.B、. IDS has shut down the computer's switch port.C、The port on the switch is configured incorrectlyD、Spanning tree protocol was implemented.
Which of the following features should an administrator configure to allow an IDS to watch thetraffic on a switch?()A、ARP spoofingB、VLANC、MirroringD、Spanning tree
Which of the following technologies allows an administrator to submit traffic to an IDS for review?()A、Spanning treeB、VLANC、PoED、Port mirroring
Which of the following devices should an administrator connect to a protocol analyzer in order tocollect all of the traffic on a LAN segment?()A、HubB、VLANC、RouterD、Server
单选题An administrator needs to connect servers to the Fiber Channel SAN. Which of the following should the administrator install in the servers to allow this connection?()ARiserBHBACSCSI cardDSAS card
单选题Why would an administrator change the value of the spanning-tree priority of a switch?()Ain order to optimize the path that frames take from source to destinationBto increase the priority so a designated port will become a root portCto increase the BID, so the switch is more likely to become root bridgeDin order to allow VLANs to be sent from one switch to another across a single linkEto force a given switch to become an STP server
多选题Which of the following are spanning tree port states?()ALearningBSpanningCListeningDForwardingEInitializingFFilteringGPermitting
单选题Which term describes a spanning-tree network that has all switch ports in either the blocking or forwardingstate? ()AredundantBspannedCprovisionedDconverged
多选题In which Spanning-Tree states does a switch port learn MAC addresses?()ABlockingBListeningCForwardingDLearningERelaying
单选题An administrator is troubleshooting a communication issue between two computers on the same Layer 2 switch. Which of the following is the BEST way to determine if the switch is causing the issue?()ASetup an ACL that allows and logs all IP traffic between the two computersBConfigure a spanning tree to check for a loopCSetup a span port on the switch to watch for CRC errorsDConnect both computers using a crossover cable
单选题Which of the following files should an administrator modify to configure dynamic caching?()Adynacache.xmlBcachespec.xmlCdynacache.confDcachemon.xmlEcachespec.conf