单选题Large crosshead type engine generally has two lubrication systems, a function performed only by crankcase oil system is()AlubricatingBcoolingCcleaningDneutralizing
单选题
Large crosshead type engine generally has two lubrication systems, a function performed only by crankcase oil system is()
A
lubricating
B
cooling
C
cleaning
D
neutralizing
参考解析
解析:
暂无解析
相关考题:
Which of the following statements concerning the lubrication of diesel propulsionengines used in vessels over 300 gross tons is most accurate? ( )A.Lubrication systems using engine driven lube oil pumps do not require any additionalindependent arrangement when such arrangements have been proven reliable.B.The use of engine driven pre-lube pumps is permitted on vessels with propulsionsystems developing less than 500 shaft horsepower.C.When forced lubrication is used for propulsion engines , one independently drivenstandby pumps is to be provided in addition to the necessary pumps for normaloperation.D.Lubrication systems where two oil coolers are fitted require a minimum of twotemperature control devices which may be actuated by similar sensors.
Exhaust gases are generally removed from the cylinders of a two-stroke/cycle diesel engine byA.natural aspirationB.masked intake valvesC.air ceilsD.scavenging air
A vessel is described as a two compartment vessel when it ______.A.has no more than two compartmentsB.has two compartments in addition to the engine roomC.will sink if any two compartments are floodedD.will float if any two adjacent compartments are flooded
Although Australia has a large area,()of the continent is desert or semi-desert.A、one thirdB、two thirdsC、halfD、more than half
单选题Exhaust gases are generally removed from the cylinders of a two-stroke/cycle diesel engine by()Anatural aspirationBmasked intake valvesCair cellsDscavenging air
单选题Mechanical lubricators for diesel engine cylinders are usually small reciprocating pumps which are ().Aoperated manually once an hourBoperated until the engine has startedCplaced into operation only at maximum loadDadjustable to meet lubrication requirements
单选题Gear-type flexible couplings are often used in diesel engine drive trains because they()Arequire no lubrication under normal operating conditionsBcompensate for gross misalignment in the drive trainCare able to transmit high torque ,even where slight misalignment existsDwill rapidly disconnect the engine from the line shaft
单选题() can be found on most medium to large merchant vessels even if the main engine is either a steam turbine or 2-stroke crosshead engine.AThe medium speed 4-stroke trunk piston engineBThe low speed 2-stroke crosshead engineCThe medium speed 2-stroke crosshead engineDThe low speed 4-stroke trunk piston engine
单选题In a bypass type lubrication system for a diesel engine, the dirty oil line to the centrifuge should be taken from the ().Alube oil pump suction lineBlube oil pump discharge lineCbottom of the lube oil sumpDoutlet from the lube oil header
单选题Large marine diesel engines of crosshead construction generally have two systems of lubrication: a total loss system feeding the () and a recirculation system lubricating the running gear and cooling the piston.Acylinder liners and piston ringsBmain bearingsCcrankpin bearingsDturboblower
单选题The main function of tie rods in the construction of large, low speed diesel engines is to().Astiffen the bedplate in way of the main bearings to increase the engines longitudinal strengthBaccept most of the tensile loading that results from the firing forces developed during operationCmount the engine frame securely to the hull to prevent shaft coupling misalignmentDconnect the crosshead solidly to the piston rod
单选题Following the failure of one turbocharger on a large, crosshead, main propulsion diesel engine, fitted with multiple turbochargers, which of the following actions should be taken prior to further operation of the engine? ()ABlank off the exhaust gas inlet to the damaged turbochargerBSecure cooling and lubrication to the damaged turbochargerCLock the rotor of the damaged turbochargerDAll of the above
单选题The engine has one or two group of fuel pumps, depending upon ().Athe number of fuel valvesBthe number of cylindersCthe speed of engineDthe power of engine
单选题Proper lubrication of the main bearing is more easily obtained in a single acting four-stroke/cycle diesel engine than in a single acting two-stroke/cycle diesel engine because ()Abearing pressure in a four-stroke/cycle acting single diesel engine is continually reversedBbearing pressure in a two-stroke/cycle single acting diesel engine is continually reversedCthe maximum bearing pressure is higher in a single acting two-stroke/cycle diesel engineDtwo-stoke/cycle diesel engines require more complicated lubrication piping
单选题Generally the function of lubrication is to form of a film of lubricant between any two surfaces that have relative (), so that surfaces dont get touch with each other.AgravityBmotionCratioDdensity
单选题A large two-stroke/cycle direct reversing diesel engine is to be reversedPrior to the admission of starting air you must ()Aline up the engine fore restarting with light diesel oilBreposition the fuel injection camCchange the intake and exhaust valve cam positionsDplace the starting cam in the intermediate position
单选题Today, crankshafts for large 2-stroke crosshead engines are of the ()type.Asemi-builtBbuilt-upCsolid forgedDindividual forged
单选题A large, low-speed, crosshead, main propulsion diesel engine using residual fuel oils must have a cylinder oil having a ()Alow TBN valueBhigh alkaline reserveClow flash pointDhigh pour point
多选题A customer has determined they want to install an IBM x445 system in their company. They will be running a large database on the system. In order to determine how many CPUs will be needed to attain the optimum cost-effective solution, which TWO of the following questions should be asked?()AHow large is the database?BWhat is the expected user workload?CHow is the database software licensed?DWhat type of user interface will be used?EHow much data cache will the database be allocated?
单选题The position of () on the crosshead on a large diesel engine is determined by dowel pins.Athe guidewayBthe piston rodCthe crosshead shoesDthe interlocked circlip
单选题The A-frames carry the crosshead guides and support the engine ().AfoundationBseatingCentablatureDbedplate
单选题()diesel engines generally have two systems of lubrication:()a total loss system feeding and a circulating system lubricating the running gear and cooling the pistons.ALarge crosshead type;crossheadsBHigh speed;the cylindersCLarge crosshead type;the cylindersDFour-stroke;pistons and cylinders
单选题Which of the listed pre-start procedures should be carried out prior to starting a crosshead type diesel engine after an overhaul?()APre-lube cylinders with hand cranksBOpen all air space drain cocksCOpen all indicator valvesDAll of the above
单选题Which of the following statements concerning the lubrication of diesel propulsion engines used in vessels over 300 gross tons is most accurate?()ALubrication systems using engine driven lube oil pumps do not require any additional independent arrangement when such arrangements have been proven reliableBThe use of engine driven pre-lube pumps is permitted on vessels with propulsion systems developing less than 500 shaft horsepowerCWhen forced lubrication is used for propulsion engines, one independently driven stand-by pumps is to be provided in addition to the necessary pumps for normal operationDLubrication systems where two oil coolers are fitted require a minimum of two temperature control devices which may be actuated by similar sensors
单选题Two important considerations for the proper lubrication of a diesel engine include the delivery of the oil in sufficient amount and the ().Acetane numberBpour pointCviscosity temperatureDquality of the oil
单选题Oil is supplied to the crosshead using a swinging arm or a () and is sometimes boosted in pressure to and efficient lubrication.Atelescopic pipeBlarge bore pipeCgenerating pipeDcentral pipe
单选题Following an overhaul of a crosshead type diesel engine, the engine is jacked over with the turning gear as part of the pre-start procedure, which of the listed pre-start procedures should be carried out?()AEnsure proper cylinder lube oil flowBOpen all air space drain cocksCOpen all indicator valvesDall of the above