单选题After creating a virtual Ethernet adapter in slot #3 of logical partition #5， the user needs to configure the adapter in AIX. Which of the following location codes matches this virtual Ethernet adapter？（）AU9111.520.1000000-V5-C3-T1BU9111.520.1000000-V3-C5-T1CU9111.520.1000000-V5-C1-T3DU9111.520.1000000-V1-C3-T5
单选题
After creating a virtual Ethernet adapter in slot #3 of logical partition #5， the user needs to configure the adapter in AIX. Which of the following location codes matches this virtual Ethernet adapter？（）
A
U9111.520.1000000-V5-C3-T1
B
U9111.520.1000000-V3-C5-T1
C
U9111.520.1000000-V5-C1-T3
D
U9111.520.1000000-V1-C3-T5
参考解析
解析：
暂无解析
相关考题：
Which of the following options applies to virtual Ethernet devices（）A、A virtual Ethernet adapter can only connect to other partitions within the same system.B、A virtual Ethernet adapter needs to be connected to an external VLAN capable switch to be able to communicate with other partitions on the same system.C、A partition can support an unlimited number of virtual Ethernet devices.D、A virtual Ethernet adapter in the VIO Server that is part of a SEA should not have the "trunk flag" set
Which three should be documented after upgrading a SCSI RAID controller？（）A、 disk utilizationB、 installation dateC、 adapter baselinesD、 location slot of the RAID controllerE、 status of the adapter card installationF、 RAID controller information （warranty， specifications etc.）
After rebuilding the list of virtual devices used by the VIO server using the "cfgdev" command， which command would be run to verify that a newly configured virtual SCSI adapter is available？（）A、lsdev -virtualB、lsdev -Cs scsiC、lscfg -vlD、lsdev -adapter
When creating a virtual Ethernet adapter on the HMC for a VIO server， what is the advantage of checking the box to access external network （trunk）？（）A、Allows the creation of a shared Ethernet adapterB、Allows the use of VLANsC、Allows the consolidation of multiple networks on one adapterD、Allows EtherChannel load balancing
Companycom will be using the Virtual IO Server to share both FC and Ethernet adapters among multiple LPARs. The customer is using mostly web services in the LPARs. Which of the following should be considered?（）A、Shared Ethernet Adapters and Virtual SCSI services require separate Virtual IO Servers.B、Virtualized adapters require essentially the same Virtual IO Server resources regardless of adapter type.C、Shared Ethernet Adapters require significantly more Virtual IO Server resources than Virtual SCSI services.D、Virtual SCSI services require significantly more Virtual IO Server resources than Shared Ethernet Adapters.
What type of configuration can provide the best availability in a Virtual IO Server environment?（）A、Provide multiple paths to all resources through 2 or more Virtual IO ServersB、Mirror all disk resources on the Virtual IO Server to present to the client LPARC、Mirror all disk resources on the client LPAR to the shared SCSI on the Virtual IO ServerD、Trunk multiple Ethernet adapters on the Virtual IO Server to a single Shared Ethernet Adapter （SEA）
When creating a Virtual Ethernet adapter， which of the following steps is done FIRST？（）A、Generate a unique MAC address.B、Run cfgmgr to create device special files.C、Create a virtual device with "smitty vlan".D、Add a virtual Ethernet adapter to the partition profile.
Company.com has two POWER5 servers. They want the two servers’ virtual Ethernets to appear on the same IP subnet. Which of the following will connect the client virtual Ethernet adapters to the physical Ethernet switch connecting the two servers？（）A、Configure a Shared Ethernet Adapter on the Virtual I/O Server.B、Use the same virtual LAN ID on each LPAR.C、Set up IP routing through an LPAR on each system.D、Set up an IP firewall through an LPAR on each system.
A FastT Host FC-2 bus adapter， a U320 SCSI adapter， and three 10/100Mb Ethernet adapters have to be installed as optimally as possible. This is going to be a 24X7 system. The addition of extra PCI-cards is a major consideration as well. Based on the following， what is the best configuration？（） （1）Slot 1 66MHz Bus 1 （2）Slot 2 66MHz Bus 1 （3）Slot 3 100MHz Bus 2 （4）Slot 4 100Mhz Bus 2 （5）Slot 5 133Mhz Bus 3 （6）Slot 6 133Mhz Bus 3A、Put the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 6.B、Put the Ethernet adapters in slots 1， 4 and 6. Put the FastT HBA in slot 5. Put the U320 adapter in slot 3.C、Put the Ethernet adapters in slots 1， 2 and 4. Put the FastT HBA in slot 3. Put the U320 adapter in slot 5.D、Put the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 4
An administrator is trying to diagnose as to why a new VIO client （vio_client1） cannot see an allocated disk （hdisk4） from a VIO server （VIOS-A）. The client virtual SCSI adapter has a slot ID of 5 and the corresponding VIO server virtual SCSI adapter has a slot ID of 3. The administrator checks the virtual SCSI configuration from the HMC using the following lshwres command. lshwres –r virtualio --rsubtype scsi -m 9117-570*65ABCDE --level lpar -F / lpar_name，slot_num，remote_lpar_name，remote_slot_num，backing_device VIOS A，5，vio_client2，2，hdisk3 VIOS-A，4，vio_client1，4，hdisk4 VIOS-A，3，vio_client1，6，hdisk5 VIOS-A，2，vio_client3，2，hdisk6 vio_client2，2，VIOS-A，5，hdisk0 vio_client1，4，VIOS-A，4，hdisk0 vio_client1，5，VIOS-A，3，null vio_client3，2，VIOS-A，2，hdisk0 From the output above， what is the most likely reason why the client cannot see the mapped storage？（）A、 The hard disk has been inccorectly mapped on the VIO server.B、 The hard disk has been incorrectly addressed on the VIO client.C、 The client SCSI adapter has been mapped to the incorrect server SCSI adapter.D、 The server SCSI adapter has been mapped to the incorrect client server adapter.
Companycom tells the technical sales specialist that recent announcements state that virtual lan in the datacenter is the best option. The customer wants to use interpartition communication to save on adapters and increase performance. The systems are going to have shared and dedicated processor partitions. Some of the partitions will be running AIX 5.2 and some will be running AIX 5.3. The second p5 590 will be running a mixture of AIX 5.3 and Linux partitions with 2.6 kernel. What limitations of vlan/interpartition communication should be discussed with this customer?（）A、Virtual Ethernet uses the system processors for all communication functions instead of offloading that load to processors on network adapter cards. Virtual Ethernet is supported on AIX 5L and Linux 2.5 and above. B、Virtual Ethernet can be used within groups of shared OR groups of dedicated processor partitions, but not both simultaneously. Virtual Ethernet comes with AIX 5L, and is supported in AIX 5.2 or AIX 5.3 partitions, but not Linux. C、Virtual Ethernet can be used in both shared and dedicated processor partitions. Virtual Ethernet can run in an AIX 5.3 or Linux 2.6 Kernel, but not AIX 5.2 partitions. Virtual Ethernet can only connect partitions within a single system. D、Virtual Ethernet uses the system processors for all communication functions instead of offloading that load to processors on network adapter cards. Virtual Ethernet can connect partitions between systems if the HMC is shared between systems.
A technical specialist defined a virtual Ethernet ent2 on the VIO server that has a physical adapter， ent0. Which of the following commands should be used to configure the Shared Ethernet Adapter？（）A、mkvdev -sea ent2 -vadapter ent0 -default ent0 -defaultid 1B、mkdev -virtual ent0 -adapter ent3 -default en2 -defaultid 1C、mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1D、mkvdev ent0 -sea -vadapter ent2 -default ent2 -defaultid 1
Company.com has a VIO server with a configured virtual Ethernet adapter and a physical Ethernet adapter with an IP address on their local public network. They want to re-configure the physical Ethernet adapter as Shared Ethernet Adapter. When the mkvdev command is run， the following method error is returned： /usr/lib/methods/cfgsea . Which of the following will most likely resolve the problem？（）A、Run cfgdev on the VIO server and re-run the mkvdev command.B、Run chdev -a sea_enable=yes on the physical Ethernet adapter.C、Remove and re-add the virtual Ethernet adapter.D、Remove the IP address from the physical adapter and re-run the mkvdev command.
Which of the following allows the user to have two separate Ethernet networks share the same network adapter？（）A、VLAN tagsB、EtherChannelC、Virtual EthernetD、Shared Ethernet Adapter
A customer has a 4-core POWER6 570 with 4 partitions and a 2-port 1Gbps Integrated Virtual Ethernet (IVE) Adapter. They are having problems with throughput on the Ethernet adapter and want to improve performance. Which of the following solutions will help the customer with this issue for the least cost and with the least interruption?（）A、Order a 2-port 1Gbps Ethernet LAN adapter.B、Order a 2-port 10Gbps Ethernet LAN adapter.C、Upgrade the IVE adapter to a 4-port 1Gbps IVE adapter.D、Upgrade the IVE adapter to a 2-port 10Gbps IVE adapter.
A server has two PCI-X buses with four Active PCI-X slots. Slots 1 and 2 are on the first PCI-X bus （100MHz） and slots 3 and 4 are on the second PCI-X bus （133MHz）. The customer requires you to install adapter A and adapter B on day one. After the server has been installed and configured， the server must be running 24 by 7 with no downtime. Three months later， adapter C needs to be hot added. All the adapters are 64-bit and capable of speeds up to 133MHz. The customer’s priority is to have no downtime， and performance is secondary. Based on the information provided， into which slots should adapters A and B be installed in and later into which slot would adapter C be hot-added？（）A、Adapter A in slot 1， adapter B in slot 4 and hot-add adapter C in slot 3B、Adapter A in slot 1， adapter B in slot 3 and hot-add adapter C in slot 2C、Adapter A in slot 2， adapter B in slot 4 and hot-add adapter C in slot 3D、Adapter A in slot 3， adapter B in slot 1 and hot-add adapter C in slot 4
Which of the following is a true statement when promiscuous mode is enabled on an Integrated Virtual Ethernet？（）A、 The physical port can be used as part of a Shared Ethernet Adapter （SEA）.B、 All physical ports on the Host Ethernet Adapter （HEA） default to promiscuous mode.C、 Multiple logical ports can be assigned to a physical port if that logical port is in promiscuous mode.D、 All physical ports that belong to the same port group will be set to promiscuous mode on the Host Ethernet Adapter （HEA）.
单选题After creating a virtual Ethernet adapter in slot #3 of logical partition #5， the user needs to configure the adapter in AIX. Which of the following location codes matches this virtual Ethernet adapter？（）AU9111.520.1000000-V5-C3-T1BU9111.520.1000000-V3-C5-T1CU9111.520.1000000-V5-C1-T3DU9111.520.1000000-V1-C3-T5
单选题When creating a Virtual Ethernet adapter， which of the following steps is done FIRST？（）AGenerate a unique MAC address.BRun cfgmgr to create device special files.CCreate a virtual device with smitty vlan.DAdd a virtual Ethernet adapter to the partition profile.
单选题Companycom tells the technical sales specialist that recent announcements state that virtual lan in the datacenter is the best option. The customer wants to use interpartition communication to save on adapters and increase performance. The systems are going to have shared and dedicated processor partitions. Some of the partitions will be running AIX 5.2 and some will be running AIX 5.3. The second p5 590 will be running a mixture of AIX 5.3 and Linux partitions with 2.6 kernel. What limitations of vlan/interpartition communication should be discussed with this customer?（）AVirtual Ethernet uses the system processors for all communication functions instead of offloading that load to processors on network adapter cards. Virtual Ethernet is supported on AIX 5L and Linux 2.5 and above. BVirtual Ethernet can be used within groups of shared OR groups of dedicated processor partitions, but not both simultaneously. Virtual Ethernet comes with AIX 5L, and is supported in AIX 5.2 or AIX 5.3 partitions, but not Linux. CVirtual Ethernet can be used in both shared and dedicated processor partitions. Virtual Ethernet can run in an AIX 5.3 or Linux 2.6 Kernel, but not AIX 5.2 partitions. Virtual Ethernet can only connect partitions within a single system. DVirtual Ethernet uses the system processors for all communication functions instead of offloading that load to processors on network adapter cards. Virtual Ethernet can connect partitions between systems if the HMC is shared between systems.
单选题Which of the following commands will NOT determine the slot location of an Ethernet adapter in a system？（）Alsattr -ElBlsdev -CCprtconfDlscfg -l
单选题Which of the following options applies to virtual Ethernet devices（）AA virtual Ethernet adapter can only connect to other partitions within the same system.BA virtual Ethernet adapter needs to be connected to an external VLAN capable switch to be able to communicate with other partitions on the same system.CA partition can support an unlimited number of virtual Ethernet devices.DA virtual Ethernet adapter in the VIO Server that is part of a SEA should not have the trunk flag set
单选题Companycom will be using Virtual IO Server to share Ethernet adapters. What can be done to prevent network failure of the client if a Virtual IO Server goes down?（）ACreate two virtual adapters on the client， each one from a separate Virtual IO ServerBEnable dead gateway detection on the client so that the network traffic can be reroutedCHave a spare network card on standby in the client in case the Virtual IO Server goes downDCreate an etherchannel adapter on the client using one Virtual Ethernet adapter from two separate Virtual IO Servers
单选题Companycom will be using the Virtual IO Server to share both FC and Ethernet adapters among multiple LPARs. The customer is using mostly web services in the LPARs. Which of the following should be considered?（）AShared Ethernet Adapters and Virtual SCSI services require separate Virtual IO Servers.BVirtualized adapters require essentially the same Virtual IO Server resources regardless of adapter type.CShared Ethernet Adapters require significantly more Virtual IO Server resources than Virtual SCSI services.DVirtual SCSI services require significantly more Virtual IO Server resources than Shared Ethernet Adapters.
单选题A server has two PCI-X buses with four Active PCI-X slots. Slots 1 and 2 are on the first PCI-X bus （100MHz） and slots 3 and 4 are on the second PCI-X bus （133MHz）. The customer requires you to install adapter A and adapter B on day one. After the server has been installed and configured， the server must be running 24 by 7 with no downtime. Three months later， adapter C needs to be hot added. All the adapters are 64-bit and capable of speeds up to 133MHz. The customer’s priority is to have no downtime， and performance is secondary. Based on the information provided， into which slots should adapters A and B be installed in and later into which slot would adapter C be hot-added？（）AAdapter A in slot 1， adapter B in slot 4 and hot-add adapter C in slot 3BAdapter A in slot 1， adapter B in slot 3 and hot-add adapter C in slot 2CAdapter A in slot 2， adapter B in slot 4 and hot-add adapter C in slot 3DAdapter A in slot 3， adapter B in slot 1 and hot-add adapter C in slot 4
单选题An administrator is supporting an AIX 6.1 LPAR remotely and needs a tape operator to plug a cable into an Ethernet adapter. The tape operator does not have POWER6 595 knowledge. What can the administrator do to assist the tape operator to locate the correct adapter？（）AAdvise the tape operator to review the hardware service guide.BUse the diag command to set the Ethernet adapter slot LED to flash.CAdvise the tape operator to check the WWN stickers of all Ethernet adapter in the I/O drawers.DCreate a login account for tape operator on the HMC and advise the tape operator to locate the adapter using the GUI step by step.
多选题Which three should be documented after upgrading a SCSI RAID controller？（）Adisk utilizationBinstallation dateCadapter baselinesDlocation slot of the RAID controllerEstatus of the adapter card installationFRAID controller information （warranty， specifications etc.）