OSPF计算cost主要是依据哪些参数（）。A、mtuB、跳数TestInside GB0-283C、带宽D、延时
OSPF计算cost主要是依据哪些参数（）。
- A、mtu
- B、跳数TestInside GB0-283
- C、带宽
- D、延时
相关考题：
When configuring OSPF on the ERX, what is the default auto－cost reference－bandwidth value?() A.AB.BC.CD.D
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?() A.1B.10C.1562D.64000E.128000
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A、An a uto - cost reference - bandwidth 1000 command in router ospf modeB、An auto - cost reference - bandwidth 2000 command in router ospf modeC、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD、An auto - cost reference - bandwidth 64700 command i n router ospf mode
关于OSPF协议，以下说法错误的是（）。A、OSPF协议是典型的链路状态路由协议B、OSPF协议中的路由开销（Cost）主要是根据跳数计算出来的C、OSPF协议采用224.0.0.18这一组播地址发送更新报文D、运行OSPF协议的路由器间通过交换LSA来获知彼此链路状态信息
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）A、1B、10C、1562D、64000E、128000
Which of the following are correct statements？（）A、EIGRP advertises the best routes to its neighborB、EIGRP uses "cost" to determine best pathC、EIGRP allows unequal cost load balancingD、OSPF requires neighbor adjacencies before updates are sentE、EIGRP advertises all routes to its neighborF、OSPF allows unequal cost load balancing
关于OSPF协议，以下说法正确的是（）A、OSPF洗衣是典型的链路状态路由协议，使用了SPF算法B、在以太网链路上，OSPF协议采用224.0.0.9这一组播地址发送更新报文C、OSPF协议中的路由开销（Cost）主要是根据链路带宽和时延计算出来的D、运行OSPF协议的路由器间通过交换LSA来获知彼此链路状态信息
多选题当前企业网络中常常会使用OSPF作为路由协议，那么在使用OSPF做路由协议的时候，需要注意哪些问题（）A确认骨干区域不会出现分裂的情况正B确认在OSPF的选路规则下，网络是否会出现次优路由C确认所有的非骨干区域与骨干区域有正确可靠的链接D确认OSPF网络拓扑结构，保证OSPF在路由计算时不会出现环路E确认OSPF的COST能够正确反映百兆以上链路的真实带宽
多选题The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1AAn a uto - cost reference - bandwidth 1000 command in router ospf modeBAn auto - cost reference - bandwidth 2000 command in router ospf modeCAn ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeDAn auto - cost reference - bandwidth 64700 command i n router ospf mode
填空题RIP是距离向量路由协议，与RIP相对，OSPF是（）协议，其cost值是根据（）来计算的。