单选题A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?（）AShow vlanBShow mac-address-tableCShow vtp statusDshow spanning-tree rootEshow ip interface brief
单选题
A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?（）
A
Show vlan
B
Show mac-address-table
C
Show vtp status
D
show spanning-tree root
E
show ip interface brief
参考解析
解析：
暂无解析
相关考题：
The network administrator has configured port security on a Ezonexam switch. Why would a network administrator configure port security on this Ezonexam device?A．To prevent unauthorized hosts from getting access to the LANB．To limit the number of Layer 2 broadcasts on a particular switch portC．To prevent unauthorized Telnet or SSH access to a switch portD．To prevent the IP and MAC address of the switch and associated portsE．None of the above
The Ezonexam network administrator needs to verify that switch interface 0/5 has been assigned to the Marketing VLA.N. Which command will accomplish this task?A. Show vlanB. Show mac-address-tableC. Show vtp statusD. show spanning-tree rootE. show ip interface briefF. None of the above
An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）A. Router routes traffic between different networks and a switch does notB. The new switch is faulty and needs to be replaced and configured correctlyC. The firewall needs to be setup to allow traffic to reach the InternetD. The switch needs to be setup to forward data traffic to the Internet
The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?（）A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.
The Ezonexam network administrator needs to a switch named VE1 to become the root bridge for a redundant path switched network. What can be done to ensure that VE1 will always assume the role as the root bridge?A．Assign the switch a higher MAC address than the other switches in the network haveB．Establish a direct link from the switch to all other switches in the networkC．Configure the switch full-duplex operation and configure the other switches for half-duplex operationD．Configure the switch so that it has lower priority than other switches in the networkE．None of the above
A network administrator needs to verify that switch interface 0／5 has been assigned to the Sales VLA.N. Which command will accomplish this task?() A. Show vlanB. Show mac-address-tableC. Show vtp statusD. show spanning-tree rootE. show ip interface brief
Refer to the exhibit.The network administrator normally establishes a telnet session with the switch from host A.However,host A is unavailable.The administrators attempt to the switch from host B fails,but pings to the other two hosts are successful.what is the issue?（）A.Host B and the switch need to be in the same subnet.B.The switch needs and appropriate default gateway assigned.C.The switch interface connected to the router is down.D.Host B need to be assigned an IP address in vlan 1.E.The switch interfaces need the appropriate IP addresses assigned.
A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?（）A、Show vlanB、Show mac-address-tableC、Show vtp statusD、show spanning-tree rootE、show ip interface brief
You have just created a new VLAN on your network for inter-VLAN routing. What is one step that you should include in your VLAN-based implementation and verification plan？（）A、Verify that different native VLANs exist between two switches for security purposes.B、Verify that the switch is configured to allow for trunking on the switch ports.C、Verify that each switch port has the proper IP address space assigned to it for the new VLAN. D、Verify that the VLAN virtual interface has been correctly created and enabled.
A network administrator needs to configure port security on a switch.which two statements are true？（）A、The network administrator can apply port security to dynamic access portsB、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.C、The sticky learning feature allows the addition of dynamically learned addresses to the runningconfiguration.D、The network administrator can apply port security to EtherChannels.E、When dynamic mac address learning is enabled on an interface，the switch can learn new addresses，up to the maximum defined.
Users report that they are unable to connect to a server. An administrator confirms that it is unreachable across the network. Other administrators have been working in the server room throughout the day. Which of the following is the NEXT step the administrator should take？（）A、 Verify the configuration of the connected port on the network switch.B、 Reboot the server.C、 Install a new NIC on the server.D、 Verify that network cables are connected.
An administrator wants to rackmount a new server. Power and network outlets are available and cooling in the room is adequate to support the additional server. The new server is identical to the other servers already installed. Which of the following items should the administrator FIRST verify before installing the server？（）A、HBA is compatible with the SAN fiber switch.B、Update the newly installed server with the latest KVM drivers.C、The UPS will continue to perform as expected with the additional load.D、Verify the server NIC is compatible with the NAS.
A network administrator needs to configure port security on a switch.which two statements are true?（）A、The network administrator can apply port security to dynamic access portsB、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.C、The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.D、The network administrator can apply port security to EtherChannels.E、When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.
You have just created a new VLAN on your network. What is one step that you should include in your VLAN-based implementation and verification plan？ （）A、Verify that trunked links are configured to allow the VLAN traffic.B、Verify that the switch is configured to allow for trunking on the switch ports.C、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.D、Verify that different native VLANs exist between two switches for security purposes.
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network?（）A、One router is running RIPv1.B、RIP neighbor is 224.0.0.9.C、The network contains a loop.D、Network 10.10.1.0 is reachable.
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。A、Establish a direct link from the switch to all other switches in the network.B、Assign the switch a higher MAC address than the other switches in the network have.C、Configure the switch so that it has a lower priority than other switches in the network.D、Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.E、Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
Before inserting a new switch in the network，the network administrator checks that the VTP domain name is correct，the VTP mode is set to server， and revision is lower than the switches in the network. The administrator then configures interfaces and trunks，erases existing VLANs，and connects the switch to the network. Following that procedure，there is no connectivity in the network. What is a possible cause of this problem？（）A、Because the configuration revision of the new switches is lower than the rest of the network， it can change the VLAN database of the other switches.B、As a VTP server， the new switch deleted all VLANs of the network.C、Erasing VLANs increases the VTP configuration revision.D、Since the configuration revision of the network is higher than the new switch， the VLAN database was automatically synchronized.
The Company network administrator needs to enable VTP pruning within the Company network. What action should a network administrator take to enable VTP pruning on an entire management domain？（）A、Enable VTP pruning on any switch in the management domainB、Enable VTP pruning on any client switch in the domainC、Enable VTP pruning on a VTP server in the management domainD、Enable VTP pruning on every switch in the domainE、None of the other alternatives apply
A user reports they cannot access the network share folder， the users workstation is configured to use automatic IP. When the administrator checks the IP address the response returns as 169.254.0.5. Which of the following should the administrator verify？（）A、 That there are no DHCP relay serversB、 That the user account on Active Directory is not lockedC、 That the network card driver is not installed incorrectlyD、 The network connection is functioning
A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）A、CAT3 cableB、Serial cableC、Crossover cableD、Rollover cable
An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）A、Router routes traffic between different networks and a switch does notB、The new switch is faulty and needs to be replaced and configured correctlyC、The firewall needs to be setup to allow traffic to reach the InternetD、The switch needs to be setup to forward data traffic to the Internet
A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）A、The switches are not stackableB、The cable was not wired using 568AC、The cable needs to be a crossover cableD、The switches have IGMP snooping enabled
An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?（）A、Battery needs to be replacedB、Light switch is turned offC、Smart cable is disconnectedD、UPS needs a firmware update
单选题Refer to the exhibit.The network administrator normally establishes a telnet session with the switch from host A.However,host A is unavailable.The administrator′s attempt to the switch from host B fails,but pings to the other two hosts are successful.what is the issue?（）A Host B and the switch need to be in the same subnet.B The switch needs and appropriate default gateway assigned.C The switch interface connected to the router is down.D Host B need to be assigned an IP address in vlan 1.E The switch interfaces need the appropriate IP addresses assigned.
单选题An administrator has a single 14U rack. The administrator needs to install fifteen servers； rack-mounted redundant uninterruptible power supplies （UPSs）， a network switch， and a KVM. Which of the following server types would be BEST suited for this scenario？（）ABlade serversBRackmount serversCTower serversDWeb servers
单选题The Company network administrator needs to enable VTP pruning within the Company network. What action should a network administrator take to enable VTP pruning on an entire management domain？（）AEnable VTP pruning on any switch in the management domainBEnable VTP pruning on any client switch in the domainCEnable VTP pruning on a VTP server in the management domainDEnable VTP pruning on every switch in the domainENone of the other alternatives apply
单选题Users report that they are unable to connect to a server. An administrator confirms that it is unreachable across the network. Other administrators have been working in the server room throughout the day. Which of the following is the NEXT step the administrator should take？（）A Verify the configuration of the connected port on the network switch.B Reboot the server.C Install a new NIC on the server.D Verify that network cables are connected.