单选题A FastT Host FC-2 bus adapter， a U320 SCSI adapter， and three 10/100Mb Ethernet adapters have to be installed as optimally as possible. This is going to be a 24X7 system. The addition of extra PCI-cards is a major consideration as well. Based on the following， what is the best configuration？（） （1）Slot 1 66MHz Bus 1 （2）Slot 2 66MHz Bus 1 （3）Slot 3 100MHz Bus 2 （4）Slot 4 100Mhz Bus 2 （5）Slot 5 133Mhz Bus 3 （6）Slot 6 133Mhz Bus 3APut the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 6.BPut the Ethernet adapters in slots 1， 4 and 6. Put the FastT HBA in slot 5. Put the U320 adapter in slot 3.CPut the Ethernet adapters in slots 1， 2 and 4. Put the FastT HBA in slot 3. Put the U320 adapter in slot 5.DPut the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 4
单选题
A FastT Host FC-2 bus adapter， a U320 SCSI adapter， and three 10/100Mb Ethernet adapters have to be installed as optimally as possible. This is going to be a 24X7 system. The addition of extra PCI-cards is a major consideration as well. Based on the following， what is the best configuration？（） （1）Slot 1 66MHz Bus 1 （2）Slot 2 66MHz Bus 1 （3）Slot 3 100MHz Bus 2 （4）Slot 4 100Mhz Bus 2 （5）Slot 5 133Mhz Bus 3 （6）Slot 6 133Mhz Bus 3
A
Put the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 6.
B
Put the Ethernet adapters in slots 1， 4 and 6. Put the FastT HBA in slot 5. Put the U320 adapter in slot 3.
C
Put the Ethernet adapters in slots 1， 2 and 4. Put the FastT HBA in slot 3. Put the U320 adapter in slot 5.
D
Put the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 4
参考解析
解析：
暂无解析
相关考题：
A customer uses an IBM xSeries x366 for their network server.They experienced downtime when the NIC failed earlier this year.Their Novell 6.5 server needs to be accessible all the time at the highest speed possible.Slots are available where network adapters can still be added. High availability is the primary requirement， but increased network bandwidth on the server is also required. Which of the following is the most cost-effective solution to satisfy all of the customer’s requirements？（）A、Upgrade the network switches to 10Gb speed.B、Install a dual port gigabit Ethernet adapter and configure adapter load balancing teaming with the onboard adapters.C、Install one extra adapter to team with the internal adapter and configure adapter failover.D、Install two additional NICs and configure adapter load balancing teaming with the onboard adapters.
Node ’A’ and ’B’ have two network adapters connected to different networks. Adapter 1 is assigned the address 192.168.0.10 with a subnet mask of 255.255.255.0. Adapter 2 is assigned the address 24.76.1.200 with a subnet mask of 255.255.240.0. What is the minimum number of additional adapters per node required to eliminate a network adapter as a single point of failure？（） A、 One adapter per nodeB、 Two adapters per nodeC、 Four adapters per nodeD、 No additional adapters per node
You are designing a Windows Server 2008 R2 Hyper-V Virtualization environment. Your host servers must have the following elements： - A dedicated management network adapter. - A dedicated virtual network for child iSCSI network traffic. - A dedicated virtual network for child network traffic with VLAN tagging. You need to choose adapters that minimize the host server processing. Which adapters should you choose？（）A、Two network adapters that support 802.1p， and one iSCSI host bus adapterB、Two network adapters that support 802.1p， and one network adapter that supports TCP ChimneyC、Two network adapters that support 802.lq， and one network adapter that supports Jumbo framesD、Three network adapters that support 802. 1p
Companycom will be using the Virtual IO Server to share both FC and Ethernet adapters among multiple LPARs. The customer is using mostly web services in the LPARs. Which of the following should be considered?（）A、Shared Ethernet Adapters and Virtual SCSI services require separate Virtual IO Servers.B、Virtualized adapters require essentially the same Virtual IO Server resources regardless of adapter type.C、Shared Ethernet Adapters require significantly more Virtual IO Server resources than Virtual SCSI services.D、Virtual SCSI services require significantly more Virtual IO Server resources than Shared Ethernet Adapters.
What is a design consideration when using existing PCIe I/O drawers in a maximum bandwidth/throughput configuration on a new Power 750 system?（）A、The new system requires 1 installed processor card for the GX++ bus adapterB、The new system requires a minimum of 2 installed processor cards for the GX++ bus adapterC、The new system requires a minimum of 3 installed processor cards and the HPC InfiniBand cluster adapterD、The new system requires 1 installed processor card for the GX++ bus adapter and the HPC InfiniBand cluster adapter
A FastT Host FC-2 bus adapter， a U320 SCSI adapter， and three 10/100Mb Ethernet adapters have to be installed as optimally as possible. This is going to be a 24X7 system. The addition of extra PCI-cards is a major consideration as well. Based on the following， what is the best configuration？（） （1）Slot 1 66MHz Bus 1 （2）Slot 2 66MHz Bus 1 （3）Slot 3 100MHz Bus 2 （4）Slot 4 100Mhz Bus 2 （5）Slot 5 133Mhz Bus 3 （6）Slot 6 133Mhz Bus 3A、Put the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 6.B、Put the Ethernet adapters in slots 1， 4 and 6. Put the FastT HBA in slot 5. Put the U320 adapter in slot 3.C、Put the Ethernet adapters in slots 1， 2 and 4. Put the FastT HBA in slot 3. Put the U320 adapter in slot 5.D、Put the Ethernet adapters in slots 1， 2 and 3. Put the FastT HBA in slot 5. Put the U320 adapter in slot 4
Company.com is having trouble installing a fresh AIX image onto a newly defined partition on a p5-520. The assignment of the adapters to the each of the partitions is as follows： Fibre Channel Card 01 - partition one - required Fibre Channel Card 02 - partition one - required SCSI adapter 01 - partition one - desired IDE adapter 01 - partition one - required Ethernet adapter 01 - partition one - required Ethernet adapter 01 - partition two - required SCSI adapter 02 - partition two - required IDE adapter 01 - partition two - desired Which of the following actions will enable the installation of the AIX image？（）A、Change the IDE adapter from desired to required in partition two and restart the partition to release the resource.B、Purchase a SCSI DVD-ROM drive to connect to the SCSI adapter in partition two.C、Purchase an LTO tape drive so that a system image backup can be created to install a new AIX partition.D、Change the IDE adapter from required to desired in partition one and restart the partition to release the resource.
A server has two PCI-X buses with four Active PCI-X slots. Slots 1 and 2 are on the first PCI-X bus （100MHz） and slots 3 and 4 are on the second PCI-X bus （133MHz）. The customer requires you to install adapter A and adapter B on day one. After the server has been installed and configured， the server must be running 24 by 7 with no downtime. Three months later， adapter C needs to be hot added. All the adapters are 64-bit and capable of speeds up to 133MHz. The customer’s priority is to have no downtime， and performance is secondary. Based on the information provided， into which slots should adapters A and B be installed in and later into which slot would adapter C be hot-added？（）A、Adapter A in slot 1， adapter B in slot 4 and hot-add adapter C in slot 3B、Adapter A in slot 1， adapter B in slot 3 and hot-add adapter C in slot 2C、Adapter A in slot 2， adapter B in slot 4 and hot-add adapter C in slot 3D、Adapter A in slot 3， adapter B in slot 1 and hot-add adapter C in slot 4
Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement：（） A、 A single adapter network using the Network Interface Card in each nodeB、 A single adapter network using persistent addresses on the Network Interface Card in each nodeC、 A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.D、 EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover
A customer uses an IBM xSeries x366. They experienced downtime when the NIC failed earlier this year. Their Windows 2003 server needs to be accessible all the time， at the highest speed possible. Two adapters are currently installed in the x366. Which of the following is the procedure to obtain the best performance and ensure network functionality in case of NIC failure？（）A、Install four NICs and configure load balancing adapter teaming.B、Install four NICs and configure adapter failover teaming.C、Install seven NICs and configure load balancing adapter teaming.D、Install one extra NIC to team with the internal adapter and configure failover teaming.
You are designing a Windows Server 2008 R2 Hyper-V virtualization environment. Your host servers must have the following elements： A dedicated management network adapter.A dedicated virtual network for child iSCSI network traffic.A dedicated virtual network for child network traffic with VLAN tagging. You need to choose adapters that minimize the host server processing. Which adapters should you choose？（）A、three network adapters that support 802.1pB、two network adapters that support 802.1q， and one iSCSI host bus adapterC、two network adapters that support 802.1p， and one network adapter that supports TCP ChimneyD、two network adapters that support 802.1q， and one network adapter that supports Jumbo frames
You have a 10Mbps network card in your computer. You install a 100Mbps network card on your computer and restart the computer. The 100Mbps card in not working due to a conflict with the10Mbps card. You want only the 100Mbps card to be active. What should you do to disable the10 Mbps network adapter？（）A、Remove the 100MB Ethernet adapter driver by using device manager.B、Remove the drivers for both Ethernet adapters cards by using device manager. C、Install the 100MB Ethernet adapter in different PC card slots.D、Disable the device drivers for the 10Mb card using by using Device Manager.
Which of the following hardware components is necessary for a server to access data directly on afiber channel based SAN？（）A、Gigabit NICB、RAID controller cardC、SATA controller cardD、Host bus adapter
单选题Companycom will be using the Virtual IO Server to share both FC and Ethernet adapters among multiple LPARs. The customer is using mostly web services in the LPARs. Which of the following should be considered?（）AShared Ethernet Adapters and Virtual SCSI services require separate Virtual IO Servers.BVirtualized adapters require essentially the same Virtual IO Server resources regardless of adapter type.CShared Ethernet Adapters require significantly more Virtual IO Server resources than Virtual SCSI services.DVirtual SCSI services require significantly more Virtual IO Server resources than Shared Ethernet Adapters.
单选题What is a design consideration when using existing PCIe I/O drawers in a maximum bandwidth/throughput configuration on a new Power 750 system?（）AThe new system requires 1 installed processor card for the GX++ bus adapterBThe new system requires a minimum of 2 installed processor cards for the GX++ bus adapterCThe new system requires a minimum of 3 installed processor cards and the HPC InfiniBand cluster adapterDThe new system requires 1 installed processor card for the GX++ bus adapter and the HPC InfiniBand cluster adapter
单选题Company.com is having trouble installing a fresh AIX image onto a newly defined partition on a p5-520. The assignment of the adapters to the each of the partitions is as follows： Fibre Channel Card 01 - partition one - required Fibre Channel Card 02 - partition one - required SCSI adapter 01 - partition one - desired IDE adapter 01 - partition one - required Ethernet adapter 01 - partition one - required Ethernet adapter 01 - partition two - required SCSI adapter 02 - partition two - required IDE adapter 01 - partition two - desired Which of the following actions will enable the installation of the AIX image？（）AChange the IDE adapter from desired to required in partition two and restart the partition to release the resource.BPurchase a SCSI DVD-ROM drive to connect to the SCSI adapter in partition two.CPurchase an LTO tape drive so that a system image backup can be created to install a new AIX partition.DChange the IDE adapter from required to desired in partition one and restart the partition to release the resource.
单选题You are designing a Windows Server 2008 R2 Hyper-V Virtualization environment. Your host servers must have the following elements： - A dedicated management network adapter. - A dedicated virtual network for child iSCSI network traffic. - A dedicated virtual network for child network traffic with VLAN tagging. You need to choose adapters that minimize the host server processing. Which adapters should you choose？（）ATwo network adapters that support 802.1p， and one iSCSI host bus adapterBTwo network adapters that support 802.1p， and one network adapter that supports TCP ChimneyCTwo network adapters that support 802.lq， and one network adapter that supports Jumbo framesDThree network adapters that support 802. 1p
单选题You have a 10Mbps network card in your computer. You install a 100Mbps network card on your computer and restart the computer. The 100Mbps card in not working due to a conflict with the10Mbps card. You want only the 100Mbps card to be active. What should you do to disable the10 Mbps network adapter？（）ARemove the 100MB Ethernet adapter driver by using device manager.BRemove the drivers for both Ethernet adapters cards by using device manager. CInstall the 100MB Ethernet adapter in different PC card slots.DDisable the device drivers for the 10Mb card using by using Device Manager.
单选题Node ’A’ and ’B’ have two network adapters connected to different networks. Adapter 1 is assigned the address 192.168.0.10 with a subnet mask of 255.255.255.0. Adapter 2 is assigned the address 24.76.1.200 with a subnet mask of 255.255.240.0. What is the minimum number of additional adapters per node required to eliminate a network adapter as a single point of failure？（）A One adapter per nodeB Two adapters per nodeC Four adapters per nodeD No additional adapters per node
单选题Which of the following allows the user to have two separate Ethernet networks share the same network adapter？（）AVLAN tagsBEtherChannelCVirtual EthernetDShared Ethernet Adapter
单选题A customer uses an IBM xSeries x366 for their network server.They experienced downtime when the NIC failed earlier this year.Their Novell 6.5 server needs to be accessible all the time at the highest speed possible.Slots are available where network adapters can still be added. High availability is the primary requirement， but increased network bandwidth on the server is also required. Which of the following is the most cost-effective solution to satisfy all of the customer’s requirements？（）AUpgrade the network switches to 10Gb speed.BInstall a dual port gigabit Ethernet adapter and configure adapter load balancing teaming with the onboard adapters.CInstall one extra adapter to team with the internal adapter and configure adapter failover.DInstall two additional NICs and configure adapter load balancing teaming with the onboard adapters.
单选题Which of the following is a true statement when promiscuous mode is enabled on an Integrated Virtual Ethernet？（）A The physical port can be used as part of a Shared Ethernet Adapter （SEA）.B All physical ports on the Host Ethernet Adapter （HEA） default to promiscuous mode.C Multiple logical ports can be assigned to a physical port if that logical port is in promiscuous mode.D All physical ports that belong to the same port group will be set to promiscuous mode on the Host Ethernet Adapter （HEA）.
单选题A customer uses an IBM xSeries x366. They experienced downtime when the NIC failed earlier this year. Their Windows 2003 server needs to be accessible all the time， at the highest speed possible. Two adapters are currently installed in the x366. Which of the following is the procedure to obtain the best performance and ensure network functionality in case of NIC failure？（）AInstall four NICs and configure load balancing adapter teaming.BInstall four NICs and configure adapter failover teaming.CInstall seven NICs and configure load balancing adapter teaming.DInstall one extra NIC to team with the internal adapter and configure failover teaming.
单选题Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement：（）A A single adapter network using the Network Interface Card in each nodeB A single adapter network using persistent addresses on the Network Interface Card in each nodeC A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.D EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover
单选题A server has two PCI-X buses with four Active PCI-X slots. Slots 1 and 2 are on the first PCI-X bus （100MHz） and slots 3 and 4 are on the second PCI-X bus （133MHz）. The customer requires you to install adapter A and adapter B on day one. After the server has been installed and configured， the server must be running 24 by 7 with no downtime. Three months later， adapter C needs to be hot added. All the adapters are 64-bit and capable of speeds up to 133MHz. The customer’s priority is to have no downtime， and performance is secondary. Based on the information provided， into which slots should adapters A and B be installed in and later into which slot would adapter C be hot-added？（）AAdapter A in slot 1， adapter B in slot 4 and hot-add adapter C in slot 3BAdapter A in slot 1， adapter B in slot 3 and hot-add adapter C in slot 2CAdapter A in slot 2， adapter B in slot 4 and hot-add adapter C in slot 3DAdapter A in slot 3， adapter B in slot 1 and hot-add adapter C in slot 4
单选题You are designing a Windows Server 2008 R2 Hyper-V virtualization environment. Your host servers must have the following elements： A dedicated management network adapter.A dedicated virtual network for child iSCSI network traffic.A dedicated virtual network for child network traffic with VLAN tagging. You need to choose adapters that minimize the host server processing. Which adapters should you choose？（）Athree network adapters that support 802.1pBtwo network adapters that support 802.1q， and one iSCSI host bus adapterCtwo network adapters that support 802.1p， and one network adapter that supports TCP ChimneyDtwo network adapters that support 802.1q， and one network adapter that supports Jumbo frames
单选题A customer has a requirement to eliminate single points of failure for an application. They have allocated one Ethernet adapter to each VIO server on the system. Which features of PowerVM and AIX will support the customer requirement？（）AEtherchannel and trunkingBNetwork Interface Backup and EtherchannelCShared Ethernet Adapter （SEA） Failover and EtherchannelDNetwork Interface Backup and Shared Ethernet Adapter failover