（10）要在一个接口上配置IP地址和子网掩码，正确的命令是哪个？（） A. Switch（config）# ip address 192.168.1.1 255.255.255.0 B. Switch（confi-if）#ip address 192.168.1.1 C. Switch（confi-if）#ip address 192.168.1.1 255.255.255.0 D. Switch（confi-if）#ip address 192.168.1.1 netmask 255.255.255.0
（10）要在一个接口上配置IP地址和子网掩码，正确的命令是哪个？（） A. Switch（config）# ip address 192.168.1.1 255.255.255.0 B. Switch（confi-if）#ip address 192.168.1.1 C. Switch（confi-if）#ip address 192.168.1.1 255.255.255.0 D. Switch（confi-if）#ip address 192.168.1.1 netmask 255.255.255.0
参考答案和解析
Router （ config-if ） #ip address 192.168.1.1 255.255.255.0
相关考题：
【问题2】（4分）根据网络拓扑和要求，完成路由器R2 上的静态路由配置。R2 (config)#ip route （5） 255.255.255.0 192.168.1.1R2 (config)#ip route 10.10.30.0 255.255.255.0 （6）R2 (config)#ip route 10.10.10.0 255.255.255.0 192.168.2.2
如下图所示为三台路由器的连接与IP地址分配，在R2中配置到达子网192.168.1.0/24的静态路由的命令是( )。A) R2(config)#ip route 192.168.1.2 255.255.255.0 10.1.1.2B) R2(config)#ip route 192.168.1.1 255.255.255.0 10.1.1.2C) R2(config)#ip route 192.168.1.2 255.255.255.0 10.1.1.1D) R2(config)#ip route 192.168.1.0 255.255.255.0 10.1.1.1
要在一个接上配置IP地址和子网掩码,正确的命令是哪个?() A.Switch（config）#ip address 192.168.1.1B.Switch（config-if）#ip address 192.168.1.1C.Switch（config-if）#ip address 192.168.1.1 255.255.255.0D.Switch（config-if）#ip address 192.168.1.1 netmask 255.255.255.0
Cisco 3548交换机采用telnet远程管理方式进行配置，其设备管理地址是222.38.12.23/24，缺省路由是222.38.12.1。下列对交换机预先进行的配置，正确的是A）Switch-3548(config)#interface vlan1Switch-3548(config-if)#ip address 222.38.12.23 255.255.255.0Switch-3548(config-if)#ip default-gateway 222.38.12.1Switch-3548(config-if)#exitSwitch-3548(config)#line vty 0 4Switch-3548(config-line)#password 7 cccSwitch-3548(config-line)#exitB）Switch-3548(config)#interface vlan1Switch-3548(config-if)#ip address 222.38.12.23 255.255.255.0Switch-3548(config-if)#exitSwitch-3548(config)#ip default-gateway 222.38.12.1Switch-3548(config)#line vty 0 4Switch-3548(config-line)#password 7 cccSwitch-3548(config-line)#exitC）Switch-3548(config)#interface vlan1Switch-3548(config-if)#ip address 222.38.12.23 255.255.255.0Switch-3548(config-if)#exitSwitch-3548(config)#ip default-route 222.38.12.1Switch-3548(config)#line vty 0 4Switch-3548(config-line)#password 7 cccSwitch-3548(config-line)#exitD）Switch-3548(config)#interface vlan1Switch-3548(config-if)#ip address 222.38.12.23 255.255.255.0Switch-3548(config-if)#exitSwitch-3548(config)#ip default-gateway 222.38.12.1Switch-3548(config)#line aux 0 4Switch-3548(config-line)#password 7 cccSwitch-3548(config-line)#exit
给一个端口配置IP192.168.1.1／30地址,命令应为()。 A.ip address 192.168.1.1 255.255.255.253B.ip address 192.168.1.1 255.255.255.250C.ip address 192.168.1.1 255.255.255.240D.ip address 192.168.1.1 255.255.255.0
下面是防火墙接口的配置命令：fire(config) ip address outside 202.134.135.98 255.255.255.252fire(config) ip address inside 192.168.46.1 255.255.255.0fire(config) ip address dmz 10.0.0.1 255.255.255.0根据以上配置，写出上图中防火墙各个端口的IP地址：e0：(2)e1：(3)e2：(4)
Switch1的f0/24口接在Switch 0的f0/2口上，请根据本题的示意图完成或解释以下 Switch0的配置命令。Switch0(config) interface(8)(进入虚子接口)Switch0(config-if) ip address 203.12.12.1 255.255.255.0(加IP地址)Switch0(config-if) no shutdown(9)Switch0(config-if) standby 1 ip 203.12.12.253(建HSRP组并设虚IP地址)Switch0(config-if) standby 1 priority 110(10)Switch0(config-if) standby 1 preempt(11)
下表是该系统中路由器的IP地址分配表。请根据上图完成以下R3路由器的配置：R3(config)interface e0/1(进入接口e0/1配置模式)R3(coafig-if) ip address 202.115.13.254(4)(设置IP地址和掩码)R3(config) interface s0/0(进入串口配置模式)R3(config-if) ip address(5)255.255.255.0(设置IP地址和掩码)R3(config) interface s0/1R3(config-if)ip address(6)255.255.255.0R3(config) interface s0/2R3(eonfig-if)ip address(7)255.255.255.0R3(config) interface s0/3R3(eonfig-if)ip address(8)255.255.255.0R3(config) interface s0/4R3(config-if)ip address(9)255.255.255.0R3(config) interface s0/5R3(config-if) ip address(10)255.255.255.0
【问题2】（3分）根据图4-1的配置，补充完成下面路由器的配置命令：Router（config）# interface （3）Router（config-if）#ip address 10.10.1.1 255.255.255.0Router（config-if）#no shutdownRouter（config-if）#exitRouter（config）# interface （4）Router（config-if）# ip address 192.168.1.1 255.255.255.0Router（config）# interface （5）Router（config-if）# ip address 10.10.2.1 255.255.255.0
You would like to operate IS－IS on interface atm 6／0.33 with an IP address of 192.168.1.1／24.Which set of commands accomplishes this?() A. router isis network 192.168.1.0 0.0.0.255B. router isis network 192.168.1.0 255.255.255.0C. interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 router isisD. interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 ip router isis
Which of the following is the subnet mask for a Class C IP address?() A.10.0.0.1B.192.168.1.1C.255.255.0.0D.255.255.255.0
在Linux系统中，使用ifconfig设置接口的IP地址并启动该接口的命令是（ ）。A.ifcorffig eth0 192.168.1.1 mask 255.255.255.0B.ifconfig 192.168.1.1 mask 255.255.255.0 upC.ifconfig eth0 192.168.1.1 mask 255.255.255.0 upD.ifconfig 192.168.1.1 255.255.255.0
某局域网通过两个路由器划分为3个子网，拓扑结构和地址分配如图5-3所示。以下是路由器R1的部分配置命令列表，请为(54)、(55)空缺处选择合适的命令/参数，实现R1的正确配置。Router(config)#hosmame R1R1(config)#int e0R1(config-if)#(54)R1(config-if)# no shutdownR1(config-if)#exitR1(config)#ip routingR1(config)#(55)A．ip address 192.168.2.1 255.255.255.0B．ip address 192.168.2.2 255.255.255.0C．ip address 192.168.3.1 255.255.255.0D．ip address 192.168.1.2 255.255.255.0
Linux系统中为一块设备名为eth0的网卡分配IP地址和子网掩码的命令是（请作答此空），如果不打算使用DNS进行地址解析，则可以将所有的主机名都放入文件（ ）中A.serserial eth0 192.168.1.1 netmask 255.255.255.0B.ifconfig eth0 192.168.1.1 netmask 255.255.255.0C.minicom eth0 192.168.1.1 netmask 255.255.255.0D.mount eth0 192.168.1.1 netmask 255.255.255.0
给一个端口配置IP192.168.1.1/30地址，命令应为（）。A、ip address 192.168.1.1 255.255.255.253B、ip address 192.168.1.1 255.255.255.250C、ip address 192.168.1.1 255.255.255.240D、ip address 192.168.1.1 255.255.255.0
要在一个接上配置IP地址和子网掩码，正确的命令是哪个？（）A、Switch（config）#ip address 192.168.1.1B、Switch（config-if）#ip address 192.168.1.1C、Switch（config-if）#ip address 192.168.1.1 255.255.255.0D、Switch（config-if）#ip address 192.168.1.1 netmask 255.255.255.0
Which of the following is the subnet mask for a Class C IP address?（）A、10.0.0.1B、192.168.1.1C、255.255.0.0D、255.255.255.0
配置思科路由器的E0/1口的IP地址的指令是（）A、ip address 1.1.1.1 255.255.255.0B、ip address 1.1.1.1C、ip 1.1.1.1D、ip 1.1.1.1 255.255.255.0
确认在接口上指定辅助IP地址的正确语法（）.A、IP SECONDARY ADDRESS10.10.10.10 255.0.0.0B、IP 10.10.10.10 255.255.0.0 secondaryC、IP address secondary 10.10.10.10 255.255.255.0D、IP address 10.10.10.10 255.255.255.0 secondary
hostname Switch1 interface Vlan10 ip address 172.16.10.32 255.255.255.0 no ip redirects standby 1 ip 172.16.10.110 standby 1 timers 1 5 standby 1 priority 130 hostname Switch2 interface Vlan10 ip address 172.16.10.33 255.255.255.0 no ip redirects standby 1 ip 172.16.10.110 standby 1 timers 1 5 standby 1 priority 120 HSRP was implemented and configured on two switches while scheduled network maintenance was performed. After the two switches have finished rebooting， you notice via show commands that Switch2 is the HSRP active router. Which two items are most likely the cause of Switch1 not becoming the active router？ （）A、premption is disabledB、standby group number does not match VLAN numberC、IP addressing is incorrectD、IP redirect is disabledE、incorrect standby timersF、booting delays
Which destination addresses will be used by Host A to send data to Host C?（）A、the IP address of Switch 1B、the MAC address of Switch 1C、the IP address of Host CD、the MAC address of Host CE、the IP address of the router's E0 interfaceF、the MAC address of the router's E0 interface
You would like to operate IS-IS on interface atm 6/0.33 with an IP address of 192.168.1.1/24. Which set of commands accomplishes this?（）A、router isis network 192.168.1.0 0.0.0.255B、router isis network 192.168.1.0 255.255.255.0C、interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 router isisD、interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 ip router isis
单选题要在一个接上配置IP地址和子网掩码，正确的命令是哪个？（）ASwitch（config）#ip address 192.168.1.1BSwitch（config-if）#ip address 192.168.1.1CSwitch（config-if）#ip address 192.168.1.1 255.255.255.0DSwitch（config-if）#ip address 192.168.1.1 netmask 255.255.255.0
单选题Which of the following is the subnet mask for a Class C IP address?（）A10.0.0.1B192.168.1.1C255.255.0.0D255.255.255.0
多选题hostname Switch1 interface Vlan10 ip address 172.16.10.32 255.255.255.0 no ip redirects standby 1 ip 172.16.10.110 standby 1 timers 1 5 standby 1 priority 130 hostname Switch2 interface Vlan10 ip address 172.16.10.33 255.255.255.0 no ip redirects standby 1 ip 172.16.10.110 standby 1 timers 1 5 standby 1 priority 120 HSRP was implemented and configured on two switches while scheduled network maintenance was performed. After the two switches have finished rebooting， you notice via show commands that Switch2 is the HSRP active router. Which two items are most likely the cause of Switch1 not becoming the active router？ （）Apremption is disabledBstandby group number does not match VLAN numberCIP addressing is incorrectDIP redirect is disabledEincorrect standby timersFbooting delays
单选题Which command configures an address of 192.168.1.1 with a mask of 255.255.255.0 on interface ge-0/0/0?（）Aset ip interface ge-0/0/0 address 192.168.1.1 255.255.255.0Bset ip interface ge-0/0/0 address 192.168.1.1/24Cset interface ge-0/0/0 ip4 address 192.168.1.1 mask 255.255.255.0Dset interfaces ge-0/0/0 unit 0 family inet address 192.168.1.1/24
单选题给一个端口配置IP192.168.1.1/30地址，命令应为（）。Aip address 192.168.1.1 255.255.255.253Bip address 192.168.1.1 255.255.255.250Cip address 192.168.1.1 255.255.255.240Dip address 192.168.1.1 255.255.255.0