多选题Which three are needed to run VRF lite for IPv6 on a router？ （）AVRF definition for IPv6BMP BGP for IPv6CLDPDVRF-enabled routing protocolEVRF-enabled interface
多选题
Which three are needed to run VRF lite for IPv6 on a router？ （）
A
VRF definition for IPv6
B
MP BGP for IPv6
C
LDP
D
VRF-enabled routing protocol
E
VRF-enabled interface
参考解析
解析：
暂无解析
相关考题：
You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? () A. set protocols isis inet6B. set routing-options router-id router-idC. set protocols ospf3 area 0 interface allD. set interface fe-0/0/1 unit 0 family inet6E. set routing-options ipv6-router-id router-id
You are troubleshooting a routing issue and need to check the hop－by－hop path to the 10.10.10.10 destination. Which three commands would display the path?() A. user@router# traceroute 10.10.10.10B. user@router ping record-route 10.10.10.10C. user@routertraceroute 10.10.10.10D. user@router# run traceroute 10.10.10.10E. user@router# ping record-route 10.10.10.10
Which command enables OSPF for IPv6?() A. router ospf ipv6 process - idB. ipv6 ospf process - idC. router ospf process - idD. ipv6 router ospf process - id
Which three of these items are found within the router advertisement message of IPv6 stateless autoconfiguration?（） (Choose three.)A、flags indicating the kind of autoconfiguration that can be done by hostsB、default router informationC、/64 prefix that can be used on the link and the lifetime of the prefixD、IPv6 DHCP server address information
Which command enables OSPF for IPv6?（）A、router ospf ipv6 process - idB、ipv6 ospf process - idC、router ospf process - idD、ipv6 router ospf process - id
Which command can be used on a PE router to connect to a CE router （11.1.1.4） in VRF red？（）A、telnet 11.1.1.4 /vrf-source redB、telnet 11.1.1.4 source /vrf redC、telnet 11.1.1.4 /source vrf redD、telnet 11.1.1.4 /vrf redE、telnet 11.1.1.4 vrf red
What does the OSPF command capability vrf-lite achieve？（）A、It enables provider edge （PE） specific checks on a router when the OSPF process is associated with the VRFB、It disables provider edge （PE） specific checks on a router when the OSPF process is associated with the VRFC、It enables the exchange of the "VRF-Lite" capability when the OSPF adjacency is formed.D、It disables the MPLS processing on the OSPF learned routes inside the VRF
Which three steps are used to configure IPv6 in JUNOS software?（）A、Assign 128-bit router id.B、Enable a routing instance.C、Assign IPv6 addresses to interfaces.D、Add IPv6 family support to interfaces.E、Enable IPv6-capable routing protocol.
When configuring Multicast VPN （MVPN） over an MPLS core， both the Default and Data MDT isconfigured under which configuration mode？（）A、router（config）#B、router（config-if）#C、router（config-vrf）#D、router（config-router）#E、router（config-router-af）#
Which command will define a VRF with name ’CCIE’ in IPv6？（）A、ip vrf CCIEB、ipv6 vrf CCIEC、vrf definition CCIED、ipv6 vrf definition CCIE
Which of the following describe the process identifier that is used to run OSPF on a router?（）A、It is logically significant.B、It is globally significant.C、It is needed to identify a unique instance of an OSPF database.D、It is an optional parameter required only if multiple OSPF processes are running on the router.E、All routers in the same OSPF area must have the same process ID if they are to exchange routing information.
Which command enables IPv6 forwarding on a cisco router?（）A、ipv6 hostB、ipv6 unicast-routingC、ipv6 localD、ipv6 neighbor
Which three causes could prevent a host from getting an IPv6 address with stateless autoconfiguration？（）A、The autoconfig command is missing from the router interface.B、IPv6 multicast routing is not enabled on the router interface.C、IPv6 unicast routing is not enabled on the router interface.D、The router interface is configured with a /63 mask.E、The router interface is configured with a /65 mask.
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a router advertisement (RA). Which two items are c ontained in the RA?（）A、any route advertisements it has receivedB、prefixes for the linkC、keepalive timersD、IPv6 address for the hostE、request for the local host IP addressF、lifetime of the prefix
Which three are needed to run VRF lite for IPv6 on a router？ （）A、VRF definition for IPv6B、MP BGP for IPv6C、LDPD、VRF-enabled routing protocolE、VRF-enabled interface
Cisco IOS XR Software Multicast Routing Implementation， which three features are supported in IPv6 onCisco CRS router？（）A、PIM-SSMB、Aggregation multicastC、PIM-BidirectionalD、OOR handlingE、integrated multicastF、Multicast NSF
单选题Which command can be used on a PE router to connect to a CE router （11.1.1.4） in VRF red？（）Atelnet 11.1.1.4 /vrf-source redBtelnet 11.1.1.4 source /vrf redCtelnet 11.1.1.4 /source vrf redDtelnet 11.1.1.4 /vrf redEtelnet 11.1.1.4 vrf red
多选题You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）Aset protocols isis inet6Bset routing-options router-id router-idCset protocols ospf3 area 0 interface allDset interface fe-0/0/1 unit 0 family inet6Eset routing-options ipv6-router-id router-id
多选题Cisco IOS XR Software Multicast Routing Implementation， which three features are supported in IPv6 onCisco CRS router？（）APIM-SSMBAggregation multicastCPIM-BidirectionalDOOR handlingEintegrated multicastFMulticast NSF
多选题Which three of these items are found within the router advertisement message of IPv6 stateless autoconfiguration?（） (Choose three.)Aflags indicating the kind of autoconfiguration that can be done by hostsBdefault router informationC/64 prefix that can be used on the link and the lifetime of the prefixDIPv6 DHCP server address information
多选题Which three steps are used to configure IPv6 in JUNOS software？（）AAssign 128-bit router IDBEnable a routing instance.CAssign IPv6 addresses to interfaces.DAdd IPv6 family support to interfaces
多选题Which three causes could prevent a host from getting an IPv6 address with stateless autoconfiguration？（）AThe autoconfig command is missing from the router interface.BIPv6 multicast routing is not enabled on the router interface.CIPv6 unicast routing is not enabled on the router interface.DThe router interface is configured with a /63 mask.EThe router interface is configured with a /65 mask.
多选题Which three steps are used to configure IPv6 in JUNOS software?（）AAssign 128-bit router id.BEnable a routing instance.CAssign IPv6 addresses to interfaces.DAdd IPv6 family support to interfaces.EEnable IPv6-capable routing protocol.
多选题Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）AConfigure a routing process using the command ipv6 router ospf [process-id].BAdd the network statement for the interfaces on which OSPF will run.CConfigure OSPF on the interface that it will run on.DUse the passive-interface command on the interfaces on which OSPF should not run.EEnable routing.
单选题Which command will define a VRF with name ’CCIE’ in IPv6？（）Aip vrf CCIEBipv6 vrf CCIECvrf definition CCIEDipv6 vrf definition CCIE
单选题What does the OSPF command capability vrf-lite achieve？（）AIt enables provider edge （PE） specific checks on a router when the OSPF process is associated with the VRFBIt disables provider edge （PE） specific checks on a router when the OSPF process is associated with the VRFCIt enables the exchange of the VRF-Lite capability when the OSPF adjacency is formed.DIt disables the MPLS processing on the OSPF learned routes inside the VRF
多选题Which three are needed to run VRF lite for IPv6 on a router？（）AVRF definition for IPv6BMP BGP for IPv6CLDPDVRF-enabled routing protocolEVRF-enabled interface
多选题You are troubleshooting a routing issue and need to check the hop-by-hop path to the 10.10.10.10 destination. Which three commands would display the path?（）Auser@router# traceroute 10.10.10.10Buser@router ping record-route 10.10.10.10Cuser@routertraceroute 10.10.10.10Duser@router# run traceroute 10.10.10.10Euser@router# ping record-route 10.10.10.10