单选题Cisco端口配置模式配置命令不正确的是（）。Ainterface s0/0Binterface Ethernet1/0Cinterface Ethernet1/0/0Dinterface 0/0
单选题
Cisco端口配置模式配置命令不正确的是（）。
A
interface s0/0
B
interface Ethernet1/0
C
interface Ethernet1/0/0
D
interface 0/0
参考解析
解析：
暂无解析
相关考题：
如果不想公布网络中的某些RIP信息，那么可以采用被动接口配置。将路由器RouterA的FastEthernet0/0接口设置为被动接口的配置语句是( )。A) RouterA(Config-if)#rip passive-interfaceB) RouterA(Config-if)#passive-interface ripC) RouterA(Config)#passive-interface fastethernet0/0D) RouterA(Config-router)#passive-interface fastethernet0/0
如果不想公布网络中的某些RIP信息，那么可以采用被动接口配置。将路由器RouterA的FastEthemet0／0接口设置为被动接口的配置语句是——。A．RouterA(Config—if)#passive—interface ripB．RouterA(Config)}}passive—interface fastethemet0／0C．RouterA(Config—router)#passive—interface fastethemet0／0D．RouterA(Config—if)#rip passive—interface
要进人以太端口配置模式，下面的路由器命令中，哪一条是正确的?——A．Router#interface e0B．Router#line eoC．Router.(confi)删ne e0D．Router(config)#interface e0
对QuidwayS3526的第12个10/100Base-T以太网端口进行配置，首先使用以下（）命令进入以太网接口视图A.interface ethernet 12B.interface ethernet1/12C.interface ethernet0/12D.interface0/12
如果需要对QuidwayS3526的一个千兆以太网口进行配置，首先需使用（）命令进入该接口视图下A.enable port ethernet1/0B.interface ethernet0/1C.interface ethernet1/1D.interface ethernet1
● 要进入以太端口配置模式，下面的路由器中命令，哪一条是正确的？（57）（57）A. R1 (config)# interface e0B. R1 interface e0C. R1 line e0D. R1 (config)# line s0
Cisco端口配置模式配置命令不正确的是()。 A.interface s0/0B.interface Ethernet1/0C.interface Ethernet1/0/0D.interface 0/0
下表是该系统中路由器的IP地址分配表。请根据上图完成以下R3路由器的配置：R3(config)interface e0/1(进入接口e0/1配置模式)R3(coafig-if) ip address 202.115.13.254(4)(设置IP地址和掩码)R3(config) interface s0/0(进入串口配置模式)R3(config-if) ip address(5)255.255.255.0(设置IP地址和掩码)R3(config) interface s0/1R3(config-if)ip address(6)255.255.255.0R3(config) interface s0/2R3(eonfig-if)ip address(7)255.255.255.0R3(config) interface s0/3R3(eonfig-if)ip address(8)255.255.255.0R3(config) interface s0/4R3(config-if)ip address(9)255.255.255.0R3(config) interface s0/5R3(config-if) ip address(10)255.255.255.0
在一台Cisco Catalyst 2950交换机上作如下配置：Switch # config terminalSwitch (config) # interface fastethernet 0/1Switch (config-if) # switchport mode accessSwitch (config-if) # switchport access vlan2若要将fastethernet 0/1端口还原到默认配置状态，可以使用( )命令。A、Switch (config) # default fastethernet 0/1B、Switch (config) # default interface fastethernet 0/1C、Switch (config) # no fastethernet 0/1D、Switch (config) # erase interface fastethernet 0/1
在交换机SWA上执行 display vlan 2 命令后，交换机输出如下：display vlan 2VLAN ID: 2VLAN Type: staticRoute interface: not configuredDescription: VLAN 0002Tagged Ports: noneUntagged Ports:Ethernet1/0/1 Ethernet1/0/3 Ethernet1/0/4从以上输出可以判断______。A. 端口 Ethernet1/0/1是一个Trunk 端口B. VLAN2 中包含了端口Ethernet1/0/1、Ethernet1/0/3 和 Ethernet1/0/4C. 带有 VLAN2 标签的数据帧离开端口Ethernet1/0/3 时需要剥离标签D. 当前交换机存在的 VLAN 只有VLAN2
Which three route filtering statements are true?() A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A. The Popcorn router is not forwarding RIP updates.B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.C. The Ethernet1 interface of the Popcorn router is shutdown.D. The clockrate is not present in the configuration of one of the routers.E. The Serial interface of the Popcorn router is not operating.
要进入以太网端口配置模式，下面的路由器命令中，哪一条是正确的？ （ ） 。A.[R1] interface e0B. interface e0C.[R1] line e0D. line s0
Cisco端口配置模式配置命令不正确的是（）。A、interface s0/0B、interface Ethernet1/0C、interface Ethernet1/0/0D、interface 0/0
monitor session 1 source interface fa 0/1 monitor session 1 destination interface fa 0/2 上述是端口镜像基本配置，端口镜像的目的端口默认不能通信，如果要通信需要在目的端口后配置参数（）A、permitB、denyC、switchD、ip
哪个两个命令正确验证是否端口快速以太网0/12端口安全性已配置的交换机？（）A、 SW1#show swithport port-security interface FastEthernet 0/12B、 SW1# show swithport port-secure interface FastEthernet 0/12C、 SW1# show port-secure interface FastEthernet 0/12D、 SW1#show running-configE、 SW1#show port-security interface FastEthernet 0/12
Your network administrator has asked you to view the real-time interface usage on ge-0/0/0, Which command whould be used?（）A、monitor interface ge0/0/0B、traceoptions interface ge-0/0/0C、debug interface ge0/0/0D、monitor usage ge-0/0/0
在交换机SWA 上执行display vlan 2 命令后，交换机输出如下： display vlan 2 VLAN ID:// 2 VLAN Type： static Route interface： not configured Description： VLAN 0002 Tagged Ports： none Untagged Ports： Ethernet1/0/1 Ethernet1/0/3 Ethernet1/0/4 从以上输出可以判断（）。A、端口Ethernet1/0/1是一个Trunk端口B、VLAN2中包含了端口Ethernet1/0/1、Ethernet1/0/3和Ethernet1/0/4C、带有VLAN2标签的数据帧离开端口Ethernet1/0/3时需要剥离标签D、当前交换机存在的VLAN只有VLAN2
在S3610交换机上创建包含有端口Ethernet1/0/1，ID为2的聚合端口，其正确命令是（）。A、[SWA] interface bridge-aggregation 2B、[SWA] interface bridge-aggregation 2 port Ethernet1/0/1C、[SWA-Ethernet1/0/1] interface bridge-aggregation 2D、[SWA-Ethernet1/0/1] interface bridge-aggregation 2 mode static
在路由器上配置静默接口来是路由器不发送OSPF协议报文的命令是（）。A、[RTA]silent-interface serial2/0B、[RTA-ospf-1]silent-interface serial2/0C、[RTA-ospf-1-area-0.0.0.1]silent-interface serial2/0D、[RTA-Serial2/0]silent-interface
Which three route filtering statements are true?（）A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Your network administrator has asked you to view the real-time interface usage on ge-0/0/0.Which command whould be used?（）A、monitor interface ge0/0/0B、traceoptions interface ge-0/0/0C、debug interface ge0/0/0D、monitor usage ge-0/0/0
单选题Cisco端口配置模式配置命令不正确的是（）。Ainterface s0/0Binterface Ethernet1/0Cinterface Ethernet1/0/0Dinterface 0/0
单选题在华为Quidway系列路由器上，用户若要查看接口Ethernt 0上的优先队列配置情况和统计信息，可以执行命令（）。A[Quidway]display qos pq interface ethernet 0B[Quidway]display qos queueing priorityC[Quidway]display qos interface ethernet 0 pqD[Quidway]display qos interface ethernet 0
单选题在华为AR路由器上，将接口配置为本地观察端口的命令是（）AObserve-port interface Ethernet2/0/3BMirror-port interface Ethernet2/0/3CMonitor-port interface Ethernet2/0/3DServer-port interface Ethernet2/0/3
多选题哪个两个命令正确验证是否端口快速以太网0/12端口安全性已配置的交换机？（）ASW1#show swithport port-security interface FastEthernet 0/12BSW1# show swithport port-secure interface FastEthernet 0/12CSW1# show port-secure interface FastEthernet 0/12DSW1#show running-configESW1#show port-security interface FastEthernet 0/12
单选题配置VRRP跟踪物理接口状态的命令是（）Avrrp vrid 1 interface GigabitEthernet0/0/0Btrack vrid 1 interface GigabitEthernet0/0/0Cvrrp vrid 1 interface GigabitEthernet0/0/0trackDvrrp vrid 1 trackinterface GigabitEthernet0/0/0