Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers.Which of the following is true on R1?（）A. The show ip ospf neighbors command lists two neighbors off Fa0/0.B. The show ip ospf neighbors command lists four neighbors off Fa0/0.C. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.D. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers.Which of the following is true on R1?（）
A. The show ip ospf neighbors command lists two neighbors off Fa0/0.
B. The show ip ospf neighbors command lists four neighbors off Fa0/0.
C. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.
D. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
相关考题：
Router R1 sets a route tag for subnet 10.1.1.0／24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?() A. Kilobits/seconDB. Tens of microsecondsC. CostD. Hop countE. No unit is assigneD
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1‘s (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.Which of the following occurs？（）A.Fa0/0 failsB.The command is rejecteDC.The existing three neighbors failD.The neighborship with 172.16.2.20 fails and then reestablishesE.None of the other answers is correct
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
R1, an ABR between backbone area 0 and area 1, has intra - area routes in area 0 for 10.1.1.0/24,10.1.2.0/24, and 10.1.3.0/24. These routes have metrics of 21, 22, and 23, respectively. An engineer then adds the area 0 r ange 10.1.0.0 255.255.0.0 command under the OSPF process of R1. Which of the following is true?（）A、R1 loses and then re - establishes neighborships with all neighbors.B、R1 no longer advertises 10.1.1.0/24 to neighbors into area 1.C、R1 advertises a 1 0.1.0.0/16 route into area 1 with a metric of 23 (largest metric).D、R1 advertises a 10.1.0.0/16 route into area 1 with metric of 21 (lowest metric).
Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）A、HostA is not on the same subnet as its default gatewayB、The address of SwitchA is a subnet addressC、The Fa0/0 interface on RouterA is on a subnet that cannot be usedD、The serial interfaces of the routers are not on the same subnetE、The Fa0/0 interface on RouterB is using a broadcast address
R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2. Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?（）A、R2's Type 1 LSAB、Subnet 10.1.1.0/24's Type 2 LSAC、ABR1's Type 1 LSA in area 0D、Subnet 10.1.1.0/24's Type 3 LSA in Area 0E、 Subnet 10.1.1.0/24's Type 3 LSA in Area 1
In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）A、Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.B、A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.C、A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.D、A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）A、R1 will always create and flood a default route into the OSPF domain.B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
Which of the following answers can be verified as true based on the following command output from Router R1?（） R1#show ip ospf virtual - links Virtual Link OSPF_VL0 to router 4.4.4.4 is up Run as demand circuit DoNotAge LSA alloweD. Transit area 1, via interface FastEthernet0/1, Cost of using 3A、R1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.B、The ping 4.4.4.4 command on R1 must currently be successful.C、R1's Fa0/0 OSPF cost is 3.D、4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode. Which of the following occurs？（）A、Fa0/0 failsB、The command is rejecteDC、The existing three neighbors failD、The neighborship with 172.16.2.20 fails and then reestablishesE、None of the other answers is correct
The following command output was gathered from Router R1, an ABR between areas 0 (backbone) and area 1. In this internetwork, area 0 contains all the subnets of cla ss A network 10.0.0.0. R1's OSPF process has a distribute - list prefix question in command configured. Assuming the subnets listed in the answers actually exist in area 0. Which of the following occurs on router R1?（） R1#sh ip prefix - list ip prefix - list question: 4 entries seq 5 deny 10.1.2.0/24 ge 25 le 27 seq 15 deny 10.2.0.0/16 ge 30 le 30 seq 20 permit 0.0.0.0/0 le 32A、R1 will not create/flood a type 3 LSA for subnet 10.1.2.0/26 into area 1B、R1 will not create/flood a Type 3 LSA for subnet 1 0.1.2.0/24 into area 1C、R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablED、R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100. Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）A、Bandwidth of 101,500B、Bandwidth of about 34,000C、Bandwidth of 500D、Delay of 1200E、Delay of 2010F、Delay of 20100
Use the same scenario as the previous question, w ith one changE.Instead of the distribute-list prefix question in command configured on R1,R1's OSPF process has an area 1 filter-list prefix question in commandconfigured. Again assuming that the subnets listed in the answers actually exist in area 0. Which of the following occurs on router R1?（） R1#sh ip prefix - list ip prefix - list question: 4 entries seq 5 deny 10.1.2.0/24 ge 25 le 27 seq 15 deny 10.2.0.0/16 ge 30 le 30 seq 20 permit 0.0.0.0/0 le 32A、R1 will not create/flood a type 3 LSA for su bnet 10.1.2.0/26 into area 1B、R1 will not create/flood a Type 3 LSA for subnet 10.1.2.0/24 into area 1C、R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablED、R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A、The show ip eigrp neighbors command on R1 lists the revised Hello timerB、The show ip eigrp interfaces command on R1 lists the revised Hello timerC、The R1 - R2 neighborship fails due to Hello timer mismatcHD、The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）A、The show ip ospf neighbors command lists two neighbors off Fa0/0.B、The show ip ospf neighbors command lists four neighbors off Fa0/0.C、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.D、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
R1 has 5 working interfaces, with EIGRP neighbors existing off each interface. R1 has routes for subnets 10.1.1.0/24, 10.1.2.0/24, and 10.1.3.0/24, with EIGRP integer metrics of roughly 1 million, 2 million, a nd 3 million, respectively. An engineer then adds the ip summary - address eigrp 1 10.1.0.0 255.255.0.0 command to interface Fa0/0. Which of the following is true?（）A、R1 loses and then reestablishes neighborships with all neighbors.B、R1 no longer advert ises 10.1.1.0/24 to neighbors connected to Fa0/0.C、1 advertises a 10.1.0.0/16 route out Fa0/0, with metric of around 3 million (largest metric of component subnets).D、R1 advertises a 10.1.0.0/16 route out Fa0/0,with metric of around 2 million (med ian metric of component subnets).
单选题R1 has 5 working interfaces, with EIGRP neighbors existing off each interface. R1 has routes for subnets 10.1.1.0/24, 10.1.2.0/24, and 10.1.3.0/24, with EIGRP integer metrics of roughly 1 million, 2 million, a nd 3 million, respectively. An engineer then adds the ip summary - address eigrp 1 10.1.0.0 255.255.0.0 command to interface Fa0/0. Which of the following is true?（）AR1 loses and then reestablishes neighborships with all neighbors.BR1 no longer advert ises 10.1.1.0/24 to neighbors connected to Fa0/0.C1 advertises a 10.1.0.0/16 route out Fa0/0, with metric of around 3 million (largest metric of component subnets).DR1 advertises a 10.1.0.0/16 route out Fa0/0,with metric of around 2 million (med ian metric of component subnets).
单选题Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）AKilobits/seconDBTens of microsecondsCCostDHop countENo unit is assigneD
单选题Which of the following answers can be verified as true based on the following command output from Router R1?（） R1#show ip ospf virtual - links Virtual Link OSPF_VL0 to router 4.4.4.4 is up Run as demand circuit DoNotAge LSA alloweD. Transit area 1, via interface FastEthernet0/1, Cost of using 3AR1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.BThe ping 4.4.4.4 command on R1 must currently be successful.CR1's Fa0/0 OSPF cost is 3.D4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
单选题R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2. Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?（）AR2's Type 1 LSABSubnet 10.1.1.0/24's Type 2 LSACABR1's Type 1 LSA in area 0DSubnet 10.1.1.0/24's Type 3 LSA in Area 0E Subnet 10.1.1.0/24's Type 3 LSA in Area 1
多选题Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）AThe show ip ospf neighbors command lists two neighbors off Fa0/0.BThe show ip ospf neighbors command lists four neighbors off Fa0/0.CThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.DThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24
多选题Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100. Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）ABandwidth of 101,500BBandwidth of about 34,000CBandwidth of 500DDelay of 1200EDelay of 2010FDelay of 20100
单选题Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）AHostA is not on the same subnet as its default gatewayBThe address of SwitchA is a subnet addressCThe Fa0/0 interface on RouterA is on a subnet that cannot be usedDThe serial interfaces of the routers are not on the same subnetEThe Fa0/0 interface on RouterB is using a broadcast address
单选题Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）AR1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.BFor any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.CFor any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.DNo subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.