A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? () A. TE1B. TE2C. TAD. NT1E. NT2
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
A. TE1
B. TE2
C. TA
D. NT1
E. NT2
相关考题：
A customer is deploying a new Junos Pulse Access Control Service and has completed the initial boot configuration as prompted using a serial connection. The customer now wants to complete the rest of the configuration using the admin GUI.Into which port on the Junos Pulse Access Control Service should the customer plug the network cable to enable access to the admin GUI?（）A. the internal interfaceB. the external interfaceC. the management interfaceD. the console interface
Serial ATA (SATA) uses a ()wire interface that creates a point－to－point connection between devices. A.Twenty-FiveB.FortyC.SixteenD.Seven
At a branch location, TestKing.com has deployed a non modular router that is equipped with two serial interfaces and two Ethernet interfaces.What additional equipment must be used to allow the branch office to connect to the central office by using an ISDN service?（）A. a serial cable with a V.35 to RJ45 adapterB. a CSU/DSUC. an external ISDN TA and NT1D. The non-modular router cannot connect to an ISDN service. The network administrator must purchase a modular router with an ISDN BRI-U card.
Which device enables a router serial interface to connect to the ISDN BRI?() A.NT2B.NT1C.TED.TAE.TE1
TestKing.com is configuring the serial interface of a Cisco router to connect to the router of a new ISP. A full T1 is being used for the Internet connection. After issuing the show interface serial 0/0 command, it is observed that the interface is UP and the line protocol is DOWN.Which of the following commands could fix this problem?（）A. Border# copy running-config startup-configB. Border(config)# no shutdownC. Border(config-if)# encapsulation pppD. Border(config-if)# no cdp enableE. Border(config-if)# ip routing
You have just obtained a modular Cisco router with 2 serial connections and a BRI／U interface. What other physical piece of hardware is required in order to establish an ISDN connection?() A. Nothing. The router is already suitable.B. A BRI WAN interface in the router.C. An external NT1 to terminate the local loop.D. A TA/NT1 device on the router.
Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.() A.Router John uses alink-state routing protocol.B.Router John will receive routing updates on the Serial0/0 interface.C.Router John will receive routing updates on the Serial0/1 interface.D.Router John will send routing updates out the Serial0/0 interface.E.Router John will send routing updates out the FastEthernet0/0 interface.F.Router John will send routing updates out the Serial0/1 interface.
The network administrator must complete the connection between the RTA of the XYZ Company and the service provider. To accomplish this task, which two devices could be installed at the customer site to provide a connection through the local loop to the central office of the provider (Choose two.)（）。A.WAN switchB.PVCC.ATM switchD.multiplexerE.CSU/DSUF.modem
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router.How should the network administrator configure the serial interface of the main office router to make the connection?（）A.B.C.D.
Use the output from the router shown in the graphic above to determine which of the following are correct.() A. Router John uses a link-state routing protocol.B. Router John will receive routing updates on the Serial0/0 interface.C. Router John will receive routing updates on the Serial0/1 interface.D. Router John will send routing updates out the Serial0/0 interface.E. Router John will send routing updates out the FastEthernet0/0 interface.F. Router John will send routing updates out the Serial0/1 interface.
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）A、show interfaces serial 0/0B、show running-configC、show versionD、show controllers serial 0/0E、show ip interfaceF、show line serial 0/0
The network administrator must complete the connection between the RTA of the XYZ Company and the service provider. To accomplish this task, which two devices could be installed at the customer site to provide a connection through the local loop to the central office of the provider (Choose two.)（）。A、WAN switchB、PVCC、ATM switchD、multiplexerE、CSU/DSUF、modem
You have just obtained a modular Cisco router with 2 serial connections and a BRI/U interface. What other physical piece of hardware is required in order to establish an ISDN connection?（）A、Nothing. The router is already suitable.B、A BRI WAN interface in the router.C、An external NT1 to terminate the local loop.D、A TA/NT1 device on the router.
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）A、TE1B、TE2C、TAD、NT1E、NT2
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）A、TE1B、TE2C、NT1D、NT2
Which device enables a router serial interface to connect to the ISDN BRI?（）A、NT2B、NT1C、TED、TAE、TE1
A customer is deploying a new Junos Pulse Access Control Service and has completed the initial boot configuration as prompted using a serial connection. The customer now wants to complete the rest of the configuration using the admin GUI.Into which port on the Junos Pulse Access Control Service should the customer plug the network cable to enable access to the admin GUI?（）A、the internal interfaceB、the external interfaceC、the management interfaceD、the console interface
Which two statements are true about the role of split horizon？（）A、It is a function used by routing protocols to install routes into routing tableB、It is a function that prevents the advertising of routes over an interface that the router is usingto reach a routeC、Its function is to help avoid routing loops.D、It is a redistribution technique used by routing protocols
TestKing.com is configuring the serial interface of a Cisco router to connect to the router of a new ISP. A full T1 is being used for the Internet connection. After issuing the show interface serial 0/0 command, it is observed that the interface is UP and the line protocol is DOWN. Which of the following commands could fix this problem?（）A、Border# copy running-config startup-configB、Border(config)# no shutdownC、Border(config-if)# encapsulation pppD、Border(config-if)# no cdp enableE、Border(config-if)# ip routing
At a branch location, TestKing.com has deployed a non modular router that is equipped with two serial interfaces and two Ethernet interfaces.What additional equipment must be used to allow the branch office to connect to the central office by using an ISDN service?（）A、a serial cable with a V.35 to RJ45 adapterB、a CSU/DSUC、an external ISDN TA and NT1D、The non-modular router cannot connect to an ISDN service. The network administrator must purchase a modular router with an ISDN BRI-U card.
单选题Serial ATA (SATA) uses a （）wire interface that creates a point-to-point connection between devices.ATwenty-FiveBFortyCSixteenDSeven
单选题Which device enables a router serial interface to connect to the ISDN BRI?（）ANT2BNT1CTEDTAETE1
多选题A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）ATE1BTE2CTADNT1ENT2
单选题A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）ATE1BTE2CNT1DNT2
单选题You have just obtained a modular Cisco router with 2 serial connections and a BRI/U interface. What other physical piece of hardware is required in order to establish an ISDN connection?（）ANothing. The router is already suitable.BA BRI WAN interface in the router.CAn external NT1 to terminate the local loop.DA TA/NT1 device on the router.
多选题The network administrator must complete the connection between the RTA of the XYZ Company and the service provider. To accomplish this task, which two devices could be installed at the customer site to provide a connection through the local loop to the central office of the provider (Choose two.)（）。AWAN switchBPVCCATM switchDmultiplexerECSU/DSUFmodem
单选题Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）Ashow interfaces serial 0/0Bshow running-configCshow versionDshow controllers serial 0/0Eshow ip interfaceFshow line serial 0/0