Which of the following statements regarding the use of multiple access lists are valid when configuring a single interface on a Cisco router?() A. Application of up to three access lists per protocol to a single interface.B. No more than two access lists per interface.C. One access list may be configured per direction for each Layer 3 protocol configured on an interface.D. The maximum number allowed varies due to RAM availability in the router.E. An infinite number of access lists that can be applied to an interface, from most specific to most general.F. Cisco IOS allows only one access list to an interface.
Which of the following statements regarding the use of multiple access lists are valid when configuring a single interface on a Cisco router?()
A. Application of up to three access lists per protocol to a single interface.
B. No more than two access lists per interface.
C. One access list may be configured per direction for each Layer 3 protocol configured on an interface.
D. The maximum number allowed varies due to RAM availability in the router.
E. An infinite number of access lists that can be applied to an interface, from most specific to most general.
F. Cisco IOS allows only one access list to an interface.
相关考题：
Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? () A. Configure a non-unique address on the loopback interface for use by the PIM RP.B. Configure MSDP with the unique address (router ID) as the local address of the peer.C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.D. Configure a unique address on the loopback interface, used as the PIM RP.
Which of the following answer choices are correct characteristics of named access list?() A. You can delete individual statements in a named access listB. Named access lists require a numbered range from 1000 to 1099.C. Named access lists must be specified as standard or extended.D. You can use the ip access-list command to create named access lists.E. You cannot delete individual statements in a named access list.F. You can use the ip name-group command to apply named access lists.
Which command shows if an access list is assigned to an interface?() A. show ip interface [interface] access-listsB. show ip access-lists interface [interface]C. show ip interface [interface]D. show ip access-lists [interface]
Refer to the diagram. All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? () A.The subnet mask in use is 255.255.255.192.B.The subnet mask in use is 255.255.255.128.C.The IP address 172.16.1.25 can be assigned to hosts in VLAN1D.The IP address 172.16.1.205 can be assigned to hosts in VLAN1E.The LAN interface of the router is configured with one IP address.F.The LAN interface of the router is configured with multiple IP addresses.
Which statement about access lists that are applied to an interface is true?() A.you can apply multiple access lists with the same protocol or in different…B.you can config one access list,per direction,per layer 3 protocolC.you can placeasmanyaccess lists as you want on any interfaceD.you can apply ony one access list on any interface
When configuring a multipoint GRE （mGRE） tunnel interface， which one of the following is NOT a valid configuration option：（）A、 tunnel sourceB、 tunnel destinationC、 tunnel keyD、 ip addressE、 tunnelvrf
Which of the following statements correctly describes the characteristics of a Frame Relay point-to-point subinterface?（）A、Needs to use Inverse ARP.B、Maps a single IP subnet per DLCI.C、Maps a single IP subnet across multiple DLCIs.D、Resolves NBMA (non broadcast multi access) split horizon issues.E、Requires use of the frame-relay map command.F、None of the above
Which of the following statements regarding the use of multiple access lists are valid when configuring a single interface on a Cisco router?（）A、Application of up to three access lists per protocol to a single interface.B、No more than two access lists per interface.C、One access list may be configured per direction for each Layer 3 protocol configured on an interface.D、The maximum number allowed varies due to RAM availability in the router.E、An infinite number of access lists that can be applied to an interface, from most specific to most general.F、Cisco IOS allows only one access list to an interface.
Which of the following are true statements regarding the characteristics of OSPF areas? Select all that apply.（）A、All OSPF networks require the use of multiple areasB、Multiple OSPF areas must connect to area 0C、Single area OSPF networks must be configured in area 1D、Areas can be assigned any number from 0 to 63535E、Area 0 is called the backbone areaF、Each OSPF area need to be configured with a loopback interface
Which command shows if an access list is assigned to an interface?（）A、show ip interface [interface] access-listsB、show ip access-lists interface [interface]C、show ip interface [interface]D、show ip access-lists [interface]
Which of the following statements regarding documentation would not be considered a helpful stepin the troubleshooting process？（）A、Use the Cisco Auto Configuration toolB、Use the Cisco Rollback featureC、Automate documentationD、Schedule documentation checksE、Use the Cisco Configuration Archive toolF、Require documentation prior to a ticket being closed out
Which two of these are correct regarding access control lists？ （Choose two.） （）A、 An ACL can be applied to multiple interlaces.B、 An ACL wildcard mask is identical to an IP subnet mask.C、 There may be multiple ACLs per protocol， per direction， and per interface.D、 There is an "implicit deny" at the end of an ACL and will result in a dropped packet.E、 An ACL acts on all packets， those flowing thru the router and those originated by the router itself.F、 An ACL will be processed from top to bottom and may have multiple matches that will act on the packet that is being tested.
Which statement about access lists that are applied to an interface is true？（）A、you can apply multiple access lists with the same protocol or in different…B、you can config one access list，per direction，per layer 3 protocolC、you can place as many access lists as you want on any interfaceD、you can apply ony one access list on any interface
When configuring the messaging system， which of the following are valid parameters for the file transport？ （）A、File NameB、Operating SystemC、LocationD、HostE、Mode
Which statements are true regarding listeners（）A、Listeners use only the TCP/IP protocol.B、Multiple listener processes can run simultaneously on a host.C、Multiple database instances can be registered with a single listener.D、The listener-related errors can be traced only at the administrative level.E、Only one database instance can be registered with a single listener at any time
Which two statements are true regarding listeners（）A、Listeners use only the TCP/IP protocol.B、Multiple listener processes can run simultaneously on a host.C、Multiple database instances can be registered with a single listener.D、The listener-related errors can be traced only at the administrative level.E、Only one database instance can be registered with a single listener at any time.
多选题When configuring the messaging system， which of the following are valid parameters for the file transport？ （）AFile NameBOperating SystemCLocationDHostEMode
多选题Flex Links are a pair of a Layer 2 interfaces (switchports or port channels), where one interface is configured to act as a backup to the other. Which two statements are correct regarding Flex Links?（）AAn interface can only belong to single Flex Links.BAn interface can belong to multiple Flex Links.CFlex Links operate only over single pairs of links.DFlex Links automatically disable STP so no BPDUs are propagated.
单选题Which of the following statements regarding the use of multiple access lists are valid when configuring a single interface on a Cisco router?（）AApplication of up to three access lists per protocol to a single interface.BNo more than two access lists per interface.COne access list may be configured per direction for each Layer 3 protocol configured on an interface.DThe maximum number allowed varies due to RAM availability in the router.EAn infinite number of access lists that can be applied to an interface, from most specific to most general.FCisco IOS allows only one access list to an interface.
多选题Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? （）AConfigure a non-unique address on the loopback interface for use by the PIM RP.BConfigure MSDP with the unique address (router ID) as the local address of the peer.CConfigure MSDP with the non-unique address (router ID) as the local address of the peer.DConfigure a unique address on the loopback interface, used as the PIM RP.
单选题Which statement about access lists that are applied to an interface is true?（）Ayou can apply multiple access lists with the same protocol or in different…Byou can config one access list,per direction,per layer 3 protocolCyou can placeasmanyaccess lists as you want on any interfaceDyou can apply ony one access list on any interface
单选题When configuring a multipoint GRE （mGRE） tunnel interface， which one of the following is NOT a valid configuration option：（）A tunnel sourceB tunnel destinationC tunnel keyD ip addressE tunnelvrf
单选题Which statement about access lists that are applied to an interface is true?（）Ayou can apply multiple access lists with the same protocol or in different direction.Byou can config one access list,per direction,per layer 3 protocolCyou can place as many access lists as you want on any interfaceDyou can apply only one access list on any interface
多选题Which of the following answer choices are correct characteristics of named access list?（）AYou can delete individual statements in a named access listBNamed access lists require a numbered range from 1000 to 1099.CNamed access lists must be specified as standard or extended.DYou can use the ip access-list command to create named access lists.EYou cannot delete individual statements in a named access list.FYou can use the ip name-group command to apply named access lists.
多选题Which of the following statements correctly describes the characteristics of a Frame Relay point-to-point subinterface?（）ANeeds to use Inverse ARP.BMaps a single IP subnet per DLCI.CMaps a single IP subnet across multiple DLCIs.DResolves NBMA (non broadcast multi access) split horizon issues.ERequires use of the frame-relay map command.FNone of the above
多选题Cisco AutoQoS takes the interface type and bandwidth into consideration when configuring which three QoS features？（）Avoice compression methodologyBLLQCCRTPDrouting protocolELFIFtrust boundary
多选题Which two of these are correct regarding access control lists？ （Choose two.） （）AAn ACL can be applied to multiple interlaces.BAn ACL wildcard mask is identical to an IP subnet mask.CThere may be multiple ACLs per protocol， per direction， and per interface.DThere is an implicit deny at the end of an ACL and will result in a dropped packet.EAn ACL acts on all packets， those flowing thru the router and those originated by the router itself.FAn ACL will be processed from top to bottom and may have multiple matches that will act on the packet that is being tested.