How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?() A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interfaceB.Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast trafficC.Configure many sub-interfaces on the same subnetD.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?()
A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface
B.Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic
C.Configure many sub-interfaces on the same subnet
D.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
相关考题：
Split horizon has been enabled within the Ezonexam routed network. Which one of the following statements best explains the split horizon rule?A．Only routers can split boundaries (horizons) between networks in separate AS numbers.B．Each AS must keep routing tables converged to prevent dead routes from being advertised across boundaries.C．Once a route is received on an interface, advertise that route as unreachable back out the same interface.D．Information about a route should never be sent back in the direction from which the original update came.E．None of the above
The Testking Central and Remote offices are configured as shown below:The remote router can be successfully pinged from the central office but the remote users can‘t access the server at the central office.Based on the output above, what do you suspect is the cause of this problem?（）A. The Frame Relay PVC is down.B. The IP addressing on the Central/Remote serial link is incorrect.C. RIP routing information is not being forwarded.D. Frame Relay inverse-ARP is not properly configured.
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）A. The ip ospf network broadcast command should be configured on each Frame Relay interfaceB. The ip ospf network non -broadcast command should be configured on each Frame Relay interfaceC. Th e ip ospf priority value on the spoke routers should be set to 0D. The ip ospf priority value on the hub router should be set to 0E. The neighbor command should be configured under the OSPF routing process on all routers
Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）A.Check and change the access lists on router RTAB.Configure the auto summary command under router eigrp 1 on router RTAC.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterfaceD.Issue the no ip split horizon command on router RTAE.Issue the no ip split horizon eigrp 1 command on router RTAF.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit.Which of the following processes are required to accomplish this task?() A. configure static frame relay map entries for each subinterface network.B. remove the ip address from the physical interfaceC. create the virtual interfaces with the interface commandD. configure each subinterface with its own IP addressE. disable split horizon to prevent routing loops between the subinterface networksF. encapsulate the physical interface with multipoint PPP
Refertotheexhibit.Tworoutershavejustbeenconfiguredbyanewtechnician.Allinterfacesareup.However,theroutersarenotsharingtheirroutingtables.Whatistheproblem?() A.Split horizon is preventing Router2 from receiving routing information from Router1.B.Router1 is configured for RIP version 2,and Router2 is configured forRIP version 1.C.Router1 has an ACL that is blocking RIP version 2.D.There is a physical connectivity problem between Router1 and Router2.E.Router1 is using authentication and Router2 is not.
A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）A、frame-relay arpB、frame-relay mapC、frame-relay interface-dlciD、frame-relay lmi-typeE、frame-relay pvc
How should arouter that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）A、Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interfaceB、Configure each Frame Relay circuit as apoint-to-point line to support multicast and broadcast trafficC、Configure many sub-interfaces on the same subnetD、Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
EIGRP is being used as the routing protocol on the PassGuide network. Whiletroubleshooting some network connectivity issues，you notice a large number of EIGRP SIA（StuckinActive）messages. What causes these SIA routes（）A、The neighboring router stops receiving ACK packets from this router.B、The neighboring router starts receiving route updates from this router.C、The neighboring router is too busy to answer the query(generally caused by high CPU utilization).D、The neighboring router is having memory problems and cannot allocate the memory to process the query or build the reply packet.
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）A、This command should be executed from the global configuration mode.B、The IP address 10.121.16.8 is the local router port used to forward data.C、102 is the remote DLCI that will receive the information.D、This command is required for all Frame Relay configurations.E、The broadcast option allows packets， such as RIP updates， to be forwarded across the PVC
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）A、The Gallant router has the wrong LMI type configuredB、Inverse ARP is providing the wrong PVC information to the Gallant routerC、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD、The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE、The IP address on the serial interface of the Attalla router is configured incorrectly
Which two statements are true about the role of split horizon？（）A、It is a function used by routing protocols to install routes into routing tableB、It is a function that prevents the advertising of routes over an interface that the router is usingto reach a routeC、Its function is to help avoid routing loops.D、It is a redistribution technique used by routing protocols
What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology?（）A、it avoids split-horizon issues with distance vector routing protocols.B、IP addresses can be conserved if VLSM is not being used for subnetting.C、A multipoint interface offers greater security compared to point-to-point subinterface configurations.D、The multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point-to-point configurations.
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtualcircuit.Which of the following processes are required to accomplish this task？（）A、configure static frame relay map entries for each subinterface network.B、remove the ip address from the physical interfaceC、create the virtual interfaces with the interface commandD、configure each subinterface with its own IP addressE、disable split horizon to prevent routing loops between the subinterface networksF、encapsulate the physical interface with multipoint PPP
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）A、Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface.B、Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic.C、Configure many sub-interfaces on the same subnet.D、Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces.
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）A、A hub router prevents routes from being advertised to the remote router.B、Only remote routers are configured as stubs.C、Stub routers are not queried for routes.D、Spoke routers connected to hub routers answer the route queries for the stub router.E、A stub router should have only EIGRP hub routers as neighbors.F、EIGRP stub routing should be used on hub routers only.
EIGRP is being used as the routing protocol on the company network. While troubleshooting somenetwork connectivity issues， you notice a large number of EIGRP SIA （Stuck in Active） messages.What causes these SIA routes？（）A、The neighboring router stops receiving ACK packets from this routerB、The neighboring router starts receiving route updates from this routerC、The neighboring router is too busy to answer the query （generally caused by high CPUutilization）D、The neighboring router is having memory problems and cannot allocate the memory to processthe query or build the reply packet
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates？（）A、Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interfaceB、Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast trafficC、Configure many sub-interfaces on the same subnetD、Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。A、This command should be executed from the global configuration modeB、The IP address 10.121.16.8 is the local router port used to forward dataC、102 is the remote DLCI that will receive the informationD、This command is required for all Frame Relay configurationsE、The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
单选题The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）AThis command should be executed from the global configuration mode.BThe IP address 10.121.16.8 is the local router port used to forward data.C102 is the remote DLCI that will receive the information.DThis command is required for all Frame Relay configurations.EThe broadcast option allows packets， such as RIP updates， to be forwarded across the PVC
单选题The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）AThe Gallant router has the wrong LMI type configuredBInverse ARP is providing the wrong PVC information to the Gallant routerCThe S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandDThe frame-relay map statement in the Attalla router for the PVC to Steele is not correctEThe IP address on the serial interface of the Attalla router is configured incorrectly
单选题The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。AThis command should be executed from the global configuration modeBThe IP address 10.121.16.8 is the local router port used to forward dataC102 is the remote DLCI that will receive the informationDThis command is required for all Frame Relay configurationsEThe broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
单选题Which one of the following potential issues is eliminated by using split horizon？（）AJoined horizonsBPacket forwarding loopsCcisco Express Forwarding load-balancing inconsistencyDAsymmetric routing throughout the network
多选题Which two statements are true about the role of split horizon？（）AIt is a function used by routing protocols to install routes into routing tableBIt is a function that prevents the advertising of routes over an interface that the router is usingto reach a routeCIts function is to help avoid routing loops.DIt is a redistribution technique used by routing protocols
单选题How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）AConfigure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the subinterface BBConfigure each Frame Relay circuit as a point-to-point line to support multicast and broadcast trafficCConfigure many sub-interfaces on the same subnetDConfigure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
多选题EIGRP is being used as the routing protocol on the PassGuide network. Whiletroubleshooting some network connectivity issues，you notice a large number of EIGRP SIA（StuckinActive）messages. What causes these SIA routes（）AThe neighboring router stops receiving ACK packets from this router.BThe neighboring router starts receiving route updates from this router.CThe neighboring router is too busy to answer the query(generally caused by high CPU utilization).DThe neighboring router is having memory problems and cannot allocate the memory to process the query or build the reply packet.
单选题What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology?（）Ait avoids split-horizon issues with distance vector routing protocols.BIP addresses can be conserved if VLSM is not being used for subnetting.CA multipoint interface offers greater security compared to point-to-point subinterface configurations.DThe multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point-to-point configurations.
多选题EIGRP is being used as the routing protocol on the company network. While troubleshooting somenetwork connectivity issues， you notice a large number of EIGRP SIA （Stuck in Active） messages.What causes these SIA routes？（）AThe neighboring router stops receiving ACK packets from this routerBThe neighboring router starts receiving route updates from this routerCThe neighboring router is too busy to answer the query （generally caused by high CPUutilization）DThe neighboring router is having memory problems and cannot allocate the memory to processthe query or build the reply packet