关于对SPEED TRIM描述不正确的是()A、低速高推力,襟翼放下时防止飞机产生低头力矩B、起飞以后十秒开始配平,爬高到400Ft以后终止配平C、飞行控制板SPEED TRIM FAIL灯亮,但按压可以复位,属单通道失效D、配平舵面是升降舵
关于对SPEED TRIM描述不正确的是()
- A、低速高推力,襟翼放下时防止飞机产生低头力矩
- B、起飞以后十秒开始配平,爬高到400Ft以后终止配平
- C、飞行控制板SPEED TRIM FAIL灯亮,但按压可以复位,属单通道失效
- D、配平舵面是升降舵
相关考题:
以下关于Trim命令的叙述中错误的是() A、该命令的功能为采用其它对象所定义的剪切边来修剪对象。B、调用Trim命令后,首先应选择修剪对象。C、修剪对象可以是直线类对象,也可以是曲线类对D、如同时按下Shift键,可在Trim命令和Extend命之间切换。
For a vessel with longitudinal inclination, an increase in GML causes ______.A.list to stabilize at an angle of lollB.trim to stabilize at an angle of lollC.trim to increaseD.trim to decrease
以下关于福特翼虎ACC智能自适应巡航控制系统的描述,不正确的是()。A、驾驶员按“set-speed”键设定速度B、雷达检测前方车辆C、ACC系统根据前方车辆间距自动调整速度D、与前车保持系统认为安全的间距
关于对MACH TRIM(马赫配平)描述不正确的是:().A、由于高马赫数飞行时,升力中心后移需要配平B、A/P不接通配平升降舵C、A/P接通配平水平安定面D、输出机构用于改变升降舵感力定中机构的中立位置
控制速度配平系统FCC(飞行控制计算机)单通道失效,导致哪些警告出现()?A、仅”SPEED TRIM FAIL”灯亮B、”SPEED TRIM FAIL”,,灯、主警告灯和系统信号灯亮C、没有任何警告出现,也无法让故障显示出来D、没有任何警告出现,但按压信号牌重现时可以使相应的故障灯和警告灯亮
单选题Which will most likely occur when entering shallow water? ()ARudder action will become more effectiveBThe vessel's list will changeCThe vessel's trim will changeDAn increase in speed will occur
单选题If keep the fuel injection of main engine unchanged when ship is fouled, that will causeⅠ.The speed of main engine to be reduced Ⅱ.Ship speed to be reduced Ⅲ.The resistance torque of propeller to be increased Ⅳ.Trim at stern to increase()AⅠ + ⅡBⅠ ~ ⅢCⅠ ~ ⅣDⅠ + Ⅱ + Ⅳ
单选题The pivoting point of a fully loaded vessel with normal trim proceeding ahead at sea speed is().Aright at the bowBone-third the length of the vessel from the bowCone-half the length of the vessel from the bowDtwo-thirds the length of the vessel from the bow
单选题The difference between the initial trim and the trim after loading is known as().AtrimBchange of trimCfinal trimDchange of draft
单选题What is MTI?().AThe foot/tons needed to trim the vessel by 1 inchBThe foot/tons needed to trim the vessel by 1 footCThe moments needed to trim the vessel by 1 centimeterDThe amount of vessel will trim when loading 100 tons 100 feet from the tipping Center
单选题以下关于Trim命令的叙述中错误的是()。A该命令的功能为采用其它对象所定义的剪切边来修剪对象。B调用Trim命令后,首先应选择修剪对象。C修剪对象可以是直线类对象,也可以是曲线类对象。D如同时按下Shift键,可在Trim命令和Extend命令之间切换。
单选题关于商品特卖活动,描述不正确的是()A对特定商品B对特定商场C有特定数量D对特定顾客