在7302 cli中执行命令show interface Shub port，部分结果如下。 isadmin# show interface shub port ============================================================ port table ============================================================ port admin-status oper-status speed type duplex ------------------------------------------------------------------------------------------ 1 up up ten-mbps network half 2 up down one-gb network full 3 down down one-gb unused full ============================================================ 以下说法错误的是：（）。A、该节点启用了2个网络口B、该7302节点的网络口1link已经UpC、该节点网络口1协商后的模式为10M半双工D、该节点的网络口1即NTIO板卡上的端口1
在7302 cli中执行命令show interface Shub port，部分结果如下。 isadmin># show interface shub port ============================================================ port table ============================================================ port admin-status oper-status speed type duplex ------------------------------------------------------------------------------------------ 1 up up ten-mbps network half 2 up down one-gb network full 3 down down one-gb unused full ============================================================ 以下说法错误的是：（）。
- A、该节点启用了2个网络口
- B、该7302节点的网络口1link已经Up
- C、该节点网络口1协商后的模式为10M半双工
- D、该节点的网络口1即NTIO板卡上的端口1
相关考题：
在华为Quidway系列路由器上,用户若要查看接口Ethernt 0上的优先队列配置情况和统计信息,可以执行命令( )。 A. Quidway#show qos-interface priority-queueB. Quidway#show queueing priorityC. Quidway#show qos-interface ethernet 0 priority-queueD. Quidway#show qos-interface ethernet 0
Which CLI command displays statistical information about a policy called goldservice ?() A. show ip interface atm 5/1.1B. show policy-list goldserviceC. show profile name goldserviceD. show rate-limit-profile goldservice
Which CLI command is used to display the IP address assigned to Dynamic Subscriber Interface and related hardware address using the DHCP Relay Proxy function?() A. show ip dhcp externalB. show dhcp binding relay-proxyC. show ip dhcp binding relay-proxyD. show dhcp relay proxy binding
Which CLI command displays the IS－IS level used by each interface?() A. show clns neighborB. show isis neighborC. show clns interfaceD. show isis interface
Which CLI command displays error statistics for an interface in real－time?() A.monitor trafficB.show interfacesC.monitor interfaceD.show interfaces extensive
Which CLI command displays packet and byte counts for an interface in real－time?() A.monitor trafficB.show interfacesC.monitor interfaceD.show traffic counts
下列哪些命令可以用来查看DDR端口（在端口 S1 上配置）信息？（ ） A、 show interface B、 show running-conting C、 show interface s1 D、 show diater interface s1
Which command shows if an access list is assigned to an interface?() A. show ip interface [interface] access-listsB. show ip access-lists interface [interface]C. show ip interface [interface]D. show ip access-lists [interface]
Whichcommandshowsif an accesslistisassignedtoaninterface?() A.show ip interface [interface] access-listsB.show ip access-lists interface [interface]C.show ip interface [interface]D.show ip access-lists [interface]
在使用Cisco IOS软件的交换机中，如下（）命令能够显示接口的状态信息（up/down）。A、show portB、show macC、show interface statusD、show ip interface briefE、shwo switchport
Cisco路由器在超级权限模式下，通过（）命令可以显示当前在NVRAM中的配置。A、show run；B、show start；C、show version；D、show interface。
Which CLI command displays statistical information about a policy called goldservice ?（）A、show ip interface atm 5/1.1B、show policy-list goldserviceC、show profile name goldserviceD、show rate-limit-profile goldservice
Which CLI command displays error statistics for an interface in real-time?（）A、monitor trafficB、show interfacesC、monitor interfaceD、show interfaces extensive
Which CLI command is used to display the IP address assigned to Dynamic Subscriber Interface and related hardware address using the DHCP Relay Proxy function?（）A、show ip dhcp externalB、show dhcp binding relay-proxyC、show ip dhcp binding relay-proxyD、show dhcp relay proxy binding
Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link？（）A、show interfaces interfaceB、show vlan briefC、show interfaces interface switchportD、show interface interface trunkE、show interfaces vlan
Which command shows if an access list is assigned to an interface?（）A、show ip interface [interface] access-listsB、show ip access-lists interface [interface]C、show ip interface [interface]D、show ip access-lists [interface]
Which one of the following commands will display the placement and direction of an IP access control list on the interfaces of a router?（）A、show interface listB、show ip routeC、show ip interfaceD、show ip interface briefE、show interface
Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?（）A、show interfaces interfaceB、show interfaces interface trunkC、show interfaces interface switchportD、show ip interface briefE、show interfaces vlan
Which CLI command displays the currently connected PPPoA subscribers?（）A、show usersB、show subscribersC、show aaa subscriberD、show connected subscriber
Which CLI command displays the IS-IS level used by each interface?（）A、show clns neighborB、show isis neighborC、show clns interfaceD、show isis interface
Which CLI command displays packet and byte counts for an interface in real-time?（）A、monitor trafficB、show interfacesC、monitor interfaceD、show traffic counts
What are two ways to view the system log files on a WX device? （）(Choose two.)A、Use the CLI and enter show log.B、Use the CLI and enter show all.C、Use the CLI and enter show logging.D、In WebView, choose Admin Tools Display System Log.
单选题In a Bridged 1483 network, which CLI commands are used to baseline an IP interface on ATM 6/1.1 and display recent IP transmit and receive statistics?（）Aclear ip interface atm 6/1.1 show ip interface atm 6/1.1Bbaseline atm interface atm 6/1.1 show ip interface atm 6/1.1Cclear ip interface atm 6/1.1 show ip interface atm 6/1.1 deltaDbaseline atm interface atm 6/1.1 show ip interface atm 6/1.1 delta
多选题哪些方式可以修改OSPF的接口开销（）A在interface视图下，执行命令ospfcostB在ospf视图下，执行命令interfacecostC在ospf视图下，执行bandwidth-referenceD在interface视图下，执行命令bandwidth-reference
多选题What are two ways to view the system log files on a WX device? （）(Choose two.)AUse the CLI and enter show log.BUse the CLI and enter show all.CUse the CLI and enter show logging.DIn WebView, choose Admin Tools Display System Log.