OSPFv3 is used to route which type of packets?（）A、IPv4B、IPv6C、MPLSD、IS-IS
OSPFv3 is used to route which type of packets?（）
- A、IPv4
- B、IPv6
- C、MPLS
- D、IS-IS
相关考题：
You have just configured a static default route on router TK1. What is the purpose of a default route?() A. It is a route to be used when the routing protocol fails.B. It is a route configured by an ISP that sends traffic into a corporate network.C. It is a route used when a packet is destined for a remote network that is not listed in the routing table.D. It is a route manually configured for a specific remote network for which a routing protocol is not configured.E. It is used to send traffic to a stub network.
The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?() A. The default administrative distance is used.B. The command is used to establish a static route.C. The command is used to configure the router interfaces.D. The command is used to establish a stub network.E. The subnet mask for the source address is 255.255.255.0
Which three are used in configuring Call Manager dial plans? () A. route listB. route groupC. gateway listD. route pattern
Which command is used to configure a default route?() A. ip route 172.16.1.0 255.255.255.0 0.0.0.0B. ip route 172.16.1.0 255.255.255.0 172.16.2.1C. ip route 0.0.0.0 255.255.255.0 172.16.2.1D. ip route 0.0.0.0 0.0.0.0 172.16.2.1
The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?（）A、The command is used to establish a static route.B、The default administrative distance is used.C、The command is used to configure the default route.D、The subnet mask for the source address is 255.255.255.0E、The command is used to establish a stub network
Which three are used in configuring Call Manager dial plans？ （）A、 route listB、 route groupC、 gateway listD、 route pattern
Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）A、chrootB、route staticC、route addD、smitty route
What is the role of route preference?（）A、It is used as a tiebreaker when the same prefix is available through multiple protocols.B、It is used to determine the preferred path to a given destination.C、It is used to select the best route between multiple equal-cost paths.D、It is used to select which routing table to use for forwarding.
Which three choices are BGP Extended communities used in MPLS-VPN deployment？（）A、Site Of Origin SOOB、Route-TargetC、Route-DistinguisherD、Domain Identifier BGP extended commumity
The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）A、The default administrative distance is used.B、The command is used to establish a static route.C、The command is used to configure the router interfaces.D、The command is used to establish a stub network.E、The subnet mask for the source address is 255.255.255.0
Which of the following commands is used to determine the route that the IP packets take to a network host?（）A、 route B、 netstat C、 iptrace D、 traceroute
Which of the following commands should be used to display a system routing table?（）A、 route B、 netstat C、 iptrace D、 traceroute
What is the role of route preference?（）A、It is used to determine which route should become active.B、It is used to select which routing table to use for forwarding.C、It is used to determine what routes to accept into the routing table.D、It is used to select the best route between multiple equal cost paths.
What is the role of route preference?（）A、It is used as a tie breaker when the same prefix is available through multiple sourcesB、It is used to determine which routes to accept into the routing tableC、It is used to select the best route between multiple equal-cost pathsD、It is used to select which routing table to use for forwarding
单选题What is the role of route preference?（）AIt is used to determine which route should become active.BIt is used to select which routing table to use for forwarding.CIt is used to determine what routes to accept into the routing table.DIt is used to select the best route between multiple equal cost paths.
单选题You have just configured a static default route on router TK1. What is the purpose of a default route?（）AIt is a route to be used when the routing protocol fails.BIt is a route configured by an ISP that sends traffic into a corporate network.CIt is a route used when a packet is destined for a remote network that is not listed in the routing table.DIt is a route manually configured for a specific remote network for which a routing protocol is not configured.EIt is used to send traffic to a stub network.
单选题Which of the following commands is used to determine the route that the IP packets take to a network host?（）A route B netstat C iptrace D traceroute
多选题Which statements are true about EIGRP successor routes?（）AA successor route is used by EIGRP to forward traffic to a destination.BSuccessor routes are saved in the topology table to be used if the primary route fails.CSuccessor routes are flagged as active in the routing table.DA successor route may be backed up by a feasible successor route.ESuccessor routes are stored in the neighbor table following the discovery process.FSuccessors are not used in EIGRP.
单选题Which statement about the use of Route Target Rewrite is true？（）AIt is mainly used in Intra-AS MPLS VPLS deployments and is configured at the ASBR to avoid misconfiguration of the Route Target assignment for VPN configurationsBIt is mainly used in Inter-AS MPLS VPN deployments and is configured at the ASBR to avoid misconfiguration of the Route Target assignment for VPN configurationsCIt is mainly used in Intra-AS MPLS VPLS deployments and is configured at the Router Reflectorto avoid misconfiguration in Route Target assignment for VPN configurationsDIt is mainly used in Inter-AS MPLS VPLS deployments and is configured at the Router Reflectorto avoid misconfiguration of the Route Target assignment for VPN configurationsEIt is mainly used in Inter-AS MPLS VPLS deployments and is configured at the PE router to avoid to misconfiguration of the Route Target assignment for VPN configurations
单选题Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）AchrootBroute staticCroute addDsmitty route
单选题What is the role of route preference?（）AIt is used as a tiebreaker when the same prefix is available through multiple protocols.BIt is used to determine the preferred path to a given destination.CIt is used to select the best route between multiple equal-cost paths.DIt is used to select which routing table to use for forwarding.
单选题Which command is used to configure a default route?（）Aip route 172.16.1.0 255.255.255.0 0.0.0.0Bip route 172.16.1.0 255.255.255.0 172.16.2.1Cip route 0.0.0.0 255.255.255.0 172.16.2.1Dip route 0.0.0.0 0.0.0.0 172.16.2.1
多选题The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?（）AThe command is used to establish a static route.BThe default administrative distance is used.CThe command is used to configure the default route.DThe subnet mask for the source address is 255.255.255.0EThe command is used to establish a stub network
单选题What is the role of route preference?（）AIt is used as a tie breaker when the same prefix is available through multiple sourcesBIt is used to determine which routes to accept into the routing tableCIt is used to select the best route between multiple equal-cost pathsDIt is used to select which routing table to use for forwarding
单选题OSPFv3 is used to route which type of packets?（）AIPv4BIPv6CMPLSDIS-IS