单选题Which of the following settings is the jumper set to when installing a DVD-RW as the second device on an IDE cable?（）AID0BID2CCable selectDMaster
单选题
Which of the following settings is the jumper set to when installing a DVD-RW as the second device on an IDE cable?（）
A
ID0
B
ID2
C
Cable select
D
Master
参考解析
解析：
暂无解析
相关考题：
A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller.Which of the following is the MOST likely cause of the problem?（）A. Both hard drives have the master jumper in place.B. One hard drive is set as master and the other slave.C. The hard drive data cable is reversed.D. Both hard drives have the cable select jumper in place.
A user has forgotten their BIOS password on their computer. Which of the following would atechnician use to allow the user access to their PC?() A. Remove the BIOS chip on the PCB. Re-flash the BIOSC. Run password cracking software on the users PCD. Set the password clear jumper on the motherboard
Which of the following settings is the jumper set to when installing a DVD－RW as the second device on an IDE cable?() A. ID0B. ID2C. Cable selectD. Master
Which of the following must occur when installing SCSI devices into the server?() A. Terminate the back end of the chain.B. Set the jumper to device ID 0.C. Terminate both ends of the chain.D. Set the jumper to cable select.
A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）A、Both hard drives have the master jumper in place.B、One hard drive is set as master and the other slave.C、The hard drive data cable is reversed.D、Both hard drives have the cable select jumper in place.
Which of the following will reset the BIOS settings?（） (Select TWO).A、Unplug the CMOS battery.B、Unplug the power supply.C、Switch on the reset jumper.D、Replace the RAM.E、Unplug the CPU.
Which of the following settings is the jumper set to when installing a DVD-RW as the second deviceon an IDE cable？（）A、 ID0B、 ID2C、 Cable selectD、 Master
Which of the following must occur when installing SCSI devices into the server？（）A、 Terminate the back end of the chain.B、 Set the jumper to device ID 0.C、 Terminate both ends of the chain.D、 Set the jumper to cable select.
In which of the following locations would a technician set the LBA mode for a hard drive？（）A、Jumper SettingsB、Disk ManagerC、Device ManagerD、System BIOS
After a technician installs a new CMOS battery on a motherboard, which of the following will thetechnician have to change? （）A、Firmware versionB、System date/timeC、Bus speedsD、Jumper settings
A user cannot undock a laptop from the docking station. Which of the following is the MOST likely cause?（）A、The laptop is not turned offB、The power cable is not unpluggedC、The lock button is set to lockD、The ACPI settings are configured improperly
Which of the following is eliminated when using SATA instead of PATA technology？（）A、Jumper selectionB、Power connectorC、Data port connectorD、Hard drive LEDs
A user has forgotten their BIOS password on their computer. Which of the following would atechnician use to allow the user access to their PC?（）A、Remove the BIOS chip on the PCB、Re-flash the BIOSC、Run password cracking software on the users PCD、Set the password clear jumper on the motherboard
The technician is repairing a PC which appears to have a failing RAM module. After replacing the module, the extra memory still is not registering. Which of the following is MOST likely the issue?（）A、Jumper settings are incorrectB、The RAM module is defectiveC、The memory slot is defectiveD、CMOS needs to be flashed
Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）A、The new drive’s jumper is set for master.B、The new drive is connected to the secondary bus as a slave drive.C、Both drives’ jumpers are set for cable select.D、The old drive’s jumper is set for master and the new drive is set for slave.
Which of the following multimeter settings should only be used when there is no electrical flow through the part being tested? （）(Select TWO).A、AmpereB、ContinuityC、VoltD、ResistanceE、Wattage
When creating a SQL tuning set，which of the following steps allows the DBA to reduce the size of the SQL set by selecting specific operators and values？（）A、 Filter versionsB、 Filter loadsC、 Filter tasksD、 Filter options
单选题When an UNDO segment is created manually by you, its availability status is set to which of the following automatically by Oracle?（）AOnline BPending online COffline DStale
单选题Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）AThe new drive’s jumper is set for master.BThe new drive is connected to the secondary bus as a slave drive.CBoth drives’ jumpers are set for cable select.DThe old drive’s jumper is set for master and the new drive is set for slave.
单选题Which of the following settings is the jumper set to when installing a DVD-RW as the second deviceon an IDE cable？（）A ID0B ID2C Cable selectD Master
单选题Which of the following must occur when installing SCSI devices into the server？（）A Terminate the back end of the chain.B Set the jumper to device ID 0.C Terminate both ends of the chain.D Set the jumper to cable select.
单选题Which of the following BIOS settings is MOST likely to speed up the boot process when disabled?（）AIDE Auto DetectBBIOS Administrator PasswordCAdvanced Configuration and Power InterfaceDPlug and Play
多选题Which of the following multimeter settings should only be used when there is no electrical flow through the part being tested? （）(Select TWO).AAmpereBContinuityCVoltDResistanceEWattage
单选题When creating a SQL tuning set，which of the following steps allows the DBA to reduce the size of the SQL set by selecting specific operators and values？（）A Filter versionsB Filter loadsC Filter tasksD Filter options
单选题Which of the following settings is the jumper set to when installing a DVD-RW as the second device on an IDE cable?（）AID0BID2CCable selectDMaster
单选题Which of the following must occur when installing SCSI devices into the server?（）ATerminate the back end of the chain.BSet the jumper to device ID 0.CTerminate both ends of the chain.DSet the jumper to cable select.
多选题Which of the following will reset the BIOS settings?（） (Select TWO).AUnplug the CMOS battery.BUnplug the power supply.CSwitch on the reset jumper.DReplace the RAM.EUnplug the CPU.