is a channel's capacity which directly reflects the data transfer rate of the channel.A.The delayB.The volumeC.The noiseD.The bandwidth

is a channel's capacity which directly reflects the data transfer rate of the channel.

A.The delay

B.The volume

C.The noise

D.The bandwidth


相关考题:

channel本身必然是同时支持读写的,所以不存在单向channel() 此题为判断题(对,错)。

关于无缓冲和有冲突的channel,下面说法正确的是() A. 无缓冲的channel是默认的缓冲为1的channelB. 无缓冲的channel和有缓冲的channel都是同步的C. 无缓冲的channel和有缓冲的channel都是非同步的D. 无缓冲的channel是同步的,而有缓冲的channel是非同步的

Which channel is designated for VHF Digital Selective Calling?A.Channel 70B.Channel 06C.Channel 13D.Channel 16

要启用LACP并将交换机端口加入端口信道1,可使用下面哪两个命令之一?() A.Switch(config)#interface port-channel1B.Switch(config)#channel-group 1 mode activeC.Switch#interface port-channel 1D.Switch(config-if)#channel-group 1 mode active

WhatinterfaceiscreatedwhenanFCPortChanneliscreatedonaCiscoUnifiedComputingSystem?() A.Aninterface’san-port-channel’inNXOSB.Aninterface’port-channel’inNXOSC.Aninterface’port-channel’with’modefc’configuredD.Aninterface’fc-port-channel’inNXOS

WhichportchannelcommandisrecommendedforN1KVonCiscoUCS?() A.channel-groupautomodeonB.channel-groupautomodeactiveC.channel-groupautomodeonsub-groupcdpD.channel-groupautomodeonsub-groupmanualE.channel-groupautomodeonmac-pinning

根据以下的配置,请判断当主接口serial0出故障后,哪一个备份接口最先被启用?()[Quidway-Serial0]standby interface serial 1 30[Quidway-Serial0]standby interface serial 2 40[Quidway-Serial0]standby logic-channel 3 50[Quidway-Serial0]standby logic-channel 2 35A.serial 1B.serial 2C.logic-channel 2D.logic-channel 3

根据以下的配置,请判断当主接口serial0出故障后,哪一个备份接口最先被启用。()Quidway(config-if-Serial0)backup interfaceserial130Quidway(config-if-Serial0)backup interfaceserial240Quidway(config-if-Serial0)backup logic-channel350Quidway(config-if-Serial0)backup logic-channel235A.serial1B.serial2C.logic-channel2D.logic-channel3

哪条命令将开始捆绑两个物理接口来通过 LACP 创建 EtherChannel 组?A.channel-group 2 mode autoB.interface port-channel 2C.channel-group 1 mode desirableD.interface range GigabitEthernet 0/4 - 5

网络管理员通过使用命令 SW1(config-if-range)# channel-group 1 mode passive 来配置交换机 SW1 和 SW2 之间的 EtherChannel 链路。必须在 SW2 上使用哪个命令来启用此 EtherChannel?()A.SW2(config-if-range)# channel-group 1 mode activeB.SW2(config-if-range)# channel-group 1 mode desirableC.SW2(config-if-range)# channel-group 1 mode autoD.SW2(config-if-range)# channel-group 1 mode passive