What are three ways an IP interface can be assigned to a virtual router in a PPP over ATM environment? ()(Choose three.) A. profileB. policy listC. domain mapD. RADIUS VSAE. classifier ACL
What are three ways an IP interface can be assigned to a virtual router in a PPP over ATM environment? ()(Choose three.)
A. profile
B. policy list
C. domain map
D. RADIUS VSA
E. classifier ACL
相关考题：
以下程序段的输出结果为 ( )int j=2；switch(j){case 2：System.out.print("two.")；case 2+1：System.out.println("three.")；breakdefault：System.out.println("value is"+j)；break；}A．two.three.B．two.C．three.D．value is 2
【问题2】（3分）根据图4-1的配置，补充完成下面路由器的配置命令：Router（config）# interface （3）Router（config-if）#ip address 10.10.1.1 255.255.255.0Router（config-if）#no shutdownRouter（config-if）#exitRouter（config）# interface （4）Router（config-if）# ip address 192.168.1.1 255.255.255.0Router（config）# interface （5）Router（config-if）# ip address 10.10.2.1 255.255.255.0
在PPPOA的协议栈中，PPP以下的协议有（）A.PPP--PPPOA--ATM--物理层B.PPP--PPPOA--AAL5--物理层C.PPP--PPPOA--物理层D.PPP--PPPOA--AAL5--ATM--物理层
Which three statements are correct regarding the CLI command, 12tp destination profile to－NewYork virtual－router vr1 ip address 1.1.1.1 ? ()(Choose three.) A. LNS IP address is defined.B. LAC IP address is defined.C. Virtual-router vr1 sends and receives L2TP traffic.D. Virtual-router vr1 is the authenticating virtual-router.E. This command is performed on the LNS.
The output of the show aaa domain-map displays the following information:Domain: isp1.com; virtual-router: vr1; loopback: 1Domain: isp2.com; virtual-router: vr2; loopback: 1Domain: none; virtual-router: vr3; loopback: 1Domain: default; virtual-router: vr4; loopback: 1The end user supplies a login name of joe@isp7.com .Which virtual router is responsible for authenticating this user?（）A. vr1B. vr2C. vr3D. vr4
以下程序段的输出结果为( )。 int j=2 switch (j){ Case 2： system.out.print("two.")： Case 2+1： System.out.println("three.")； break： default: System.out.println (“value is”+j): Break }A.B.twoA．two.three.B．twoC．threeD．value is 2
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:*Mar 1 00:2 5:01.084: %OSPF -4- ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0 .How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?（）A.R1(config - router)# area 0 virtual - link 1.1.1.1R3(config - router)# area 2 virtual - link 3.3.3.3B.R1(config - router)# area 1 virtual - link 2.2.2.2 R3(config - router)# area 1 virtual - link 2.2.2.2C.R1(config - router)# area 1 virtual - link 20.20 .20.2 R3(config - router)# area 1 virtual - link 30.30.30.2D.R1(config - router)# area 1 virtual - link 30.30.30.3 R3(config - router)# area 1 virtual - link 20.20.20.1E.R1(config - router)# area 1 virtual - link 3.3.3.3 R3(config - router)# area 1 virtual - link 1.1 .1.1
3、【STCS_03_2】配置PPP验证方式为chap的命令为：A．Router(config)#encapsulation ppp chapB．Router(config-if)#encapsulation chapC．Router(config-if)#ppp authentication chapD．Router(config-if)#encapsulation ppp chap
2、【STCS_03_2】给接口配置PPP协议的命令：A．Router(config)#encapsulation pppB．Router(config-if)#encapsulation pppC．Router(config-if)#encapsulation papD．Router(config-if)#encapsulation ppp pap