Which configuration component is required to allow a PPP over ATM client to connect to one virtual router for a particular session and to a different virtual router for another session?() A. profileB. domain mapC. IP access-routeD. static IP addressing
Which configuration component is required to allow a PPP over ATM client to connect to one virtual router for a particular session and to a different virtual router for another session?()
A. profile
B. domain map
C. IP access-route
D. static IP addressing
相关考题：
假设在LAC路由器上运行show vpdn命令，路由器软件系统输出的配置信息如图8-18所示。结合图 8-16所示的网络拓扑结构，请将(5)～(9)空缺处填写完整，完成在LAC上对L2TPv2协议的相关配置。Router_LAC(config) vpdn enableRouter_LAC(config) (5) (创建相应vPdn组，并进入该组的配置模式)(6) (接受对端发起L2TP通道连接请求，并根据virtual-template 1创建virtual-access接口)Router_LAC(config-vpdn1) (7) (启用L2TP通道验证功能)Router_LAC(config-vpdn1) 12tp tunnel password !abcd1234!(8)Router_LAC (config) (9) (创建并进入相应的L2TP虚接口模板)(其他配置略)
假设在LAC路由器上运行show vpdn命令，路由器软件系统输出的配置信息如图5-17所示。结合图 5-15所示的网络拓扑结构，请将(5)～(9)空缺处填写完整，完成在LAC上对L2TPv2协议的相关配置。Router_LAC(config)vpdn enableRouter_LAC(config) (5) (创建相应vpdn组，并进入该组的配置模式)(6) (接受对端发起L2TP通道连接请求，并根据virtual—template 1创建virtual-access接口)Router_LAC(config-vpdnl) (7) (启用L2TP通道验证功能)Router_LAC(config-vpdnl)12tp tunnel password! abcd1234!(8)Router_LAC(config) (9) (创建并进入相应的L2TP虚接口模板)(其他配置略)
Which IDP policy action closes the connection and sends an RST packet to both the client and the server?() A. close-connectionB. terminate-connectionC. close-client-and-serverD. terminate-session
Which three statements are correct regarding the CLI command, 12tp destination profile to－NewYork virtual－router vr1 ip address 1.1.1.1 ? ()(Choose three.) A. LNS IP address is defined.B. LAC IP address is defined.C. Virtual-router vr1 sends and receives L2TP traffic.D. Virtual-router vr1 is the authenticating virtual-router.E. This command is performed on the LNS.
The output of the show aaa domain-map displays the following information:Domain: isp1.com; virtual-router: vr1; loopback: 1Domain: isp2.com; virtual-router: vr2; loopback: 1Domain: none; virtual-router: vr3; loopback: 1Domain: default; virtual-router: vr4; loopback: 1The end user supplies a login name of joe@isp7.com .Which virtual router is responsible for authenticating this user?（）A. vr1B. vr2C. vr3D. vr4
Which command will delete the current rescue configuration?() A. user@router# system delete configuration rescueB. user@router request system configuration rescue deleteC. user@router# delete rescue configurationD. user@router file delete rescue-configuration
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:*Mar 1 00:2 5:01.084: %OSPF -4- ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0 .How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?（）A.R1(config - router)# area 0 virtual - link 1.1.1.1R3(config - router)# area 2 virtual - link 3.3.3.3B.R1(config - router)# area 1 virtual - link 2.2.2.2 R3(config - router)# area 1 virtual - link 2.2.2.2C.R1(config - router)# area 1 virtual - link 20.20 .20.2 R3(config - router)# area 1 virtual - link 30.30.30.2D.R1(config - router)# area 1 virtual - link 30.30.30.3 R3(config - router)# area 1 virtual - link 20.20.20.1E.R1(config - router)# area 1 virtual - link 3.3.3.3 R3(config - router)# area 1 virtual - link 1.1 .1.1
3、【STCS_03_2】配置PPP验证方式为chap的命令为：A．Router(config)#encapsulation ppp chapB．Router(config-if)#encapsulation chapC．Router(config-if)#ppp authentication chapD．Router(config-if)#encapsulation ppp chap
2、【STCS_03_2】给接口配置PPP协议的命令：A．Router(config)#encapsulation pppB．Router(config-if)#encapsulation pppC．Router(config-if)#encapsulation papD．Router(config-if)#encapsulation ppp pap