You have been asked to establish reachability between Router 1‘s and Router 2‘s loopback addresses as shown in the exhibit. Which two steps will accomplish this task?() A. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.2.B. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.1.C. Create a static route on Router 2 to 172.17.25.1 with a next hop of 10.10.10.1.D. Create a static route on Router 1 to 172.17.25.1 with a next hop of 10.10.10.2.
You have been asked to establish reachability between Router 1‘s and Router 2‘s loopback addresses as shown in the exhibit. Which two steps will accomplish this task?()
A. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.2.
B. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.1.
C. Create a static route on Router 2 to 172.17.25.1 with a next hop of 10.10.10.1.
D. Create a static route on Router 1 to 172.17.25.1 with a next hop of 10.10.10.2.
相关考题：
The output of the show aaa domain-map displays the following information:Domain: isp1.com; virtual-router: vr1; loopback: 1Domain: isp2.com; virtual-router: vr2; loopback: 1Domain: none; virtual-router: vr3; loopback: 1Domain: default; virtual-router: vr4; loopback: 1The end user supplies a login name of joe@isp7.com .Which virtual router is responsible for authenticating this user?（）A. vr1B. vr2C. vr3D. vr4
● 试题五阅读以下说明，将应填入(n)处的解答填写在答题纸的对应栏内。【说明】某网络结构如图6所示，如果Router3与网络4之间的线路突然中断，按照RIP路由协议的实现方法，路由表的更新时间间隔为30s，中断30s后Router2的路由信息表1和中断500s后Router2的路由信息表2见表1、表2。注：①若到达目的网络不需转发或目的网络不可达，用"-"来表示"下一站地址"；②当目的网络不可达时，"跳数"为16。图6网络结构图［问题］1．请填充中断30s后Router2的路由信息表1。2．请填充中断500s后Router2的路由信息表2。
阅读以下说明，回答问题1～5，将解答填入对应的解答栏内。在图4-1所示的网络中，运行的路由协议是OSPF，有0、1和2三个区域，其中Router1的S0端口、Router2的S0端口属于区域0，Router1的E0端口、Router3的E0端口属于区域1，Router2的E0端口、Router4的E0端口属于区域2。根据路由选择算法，动态路由分为(1)、(2)、(3)。OSPF属于(4)。
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?() A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0E. Router(config)# ip route any any e0
关于动态路由协议中的路由ID描述错误的是() A.如果使用router-id命令手工配置router-id，就使用该router-idB.如果没有手工配置router-id并且配置了loopback接口地址，则选了loopback接口地址最大的作为router-idC.如果没有配置router-id且米有配置loopback接口地址，则从其物理接口的IP地址中选择最大的作为router-idD.Router-id改变之后，各个协议的router-id就会改变，不需要额外的操作
下列所述 的配置中，哪一个是 允许来 自网段172.16.0.0 的数据包 进入路由器 的串口0？ （）。A.Router(config)#access-list 10 permit 172.16.0.0 0.0.255.255 Router(config)#interface s0 Router (config-int-s0)#ip access-group 10 out#B.Router (config)#access-group 10 permit 172.16.0.0 255.255.0.0 Router(config)#interface s0 、Router (config-int-s0)#ip access-list 10 out#C.Router (config)#access-list 10 permit 172.16.0.0 0.0.255.255 Router(config)#interface s0 Router (config-int-s0)#ip access-group 10 in#D.Router (config
3、下列所述 的配置中，哪一个是 允许来 自网段172.16.0.0 的数据包 进入路由器 的串口0？ （）。A.Router(config)#access-list 10 permit 172.16.0.0 0.0.255.255 Router(config)#interface s0 Router (config-int-s0)#ip access-group 10 out#B.Router (config)#access-group 10 permit 172.16.0.0 255.255.0.0 Router(config)#interface s0 、Router (config-int-s0)#ip access-list 10 out#C.Router (config)#access-list 10 permit 172.16.0.0 0.0.255.255 Router(config)#interface s0 Router (config-int-s0)#ip access-group 10 in#D.Router (config