Which RIP configuration command allows the ERX Edge Router to send Unicast updates to configured neighbors?() A.neighborB.unicast-neighborC.triggered-updateD.passive-interface
Which RIP configuration command allows the ERX Edge Router to send Unicast updates to configured neighbors?()
A.neighbor
B.unicast-neighbor
C.triggered-update
D.passive-interface
相关考题：
在Cisco路由器上配置RIPvl路由协议，参与RIP路由的网络地址有193.22.56.0/26、193.22.56.64/26、193.22.56.128/26和193.22.56.192/26，正确的配置命令是( )。A) Router(config)# netword 193.22.56.0 0.0.0.255B) Router(config-router)# netword 193.22.56.0 255.255.255.0C) Router(config)# netword 193.22.56.0D) Router(config-router)# netword 193.22.56.0
如果要对RIP进行调试排错,应该使用哪一个命令?() A.Router（config-router）#debug ip ripB.Router#show ip rip eventC.Router（config-router）#show ip interfaceD.Router#debug ip rip
阅读以下说明，回答问题1、问题2、问题3和问题4，将解答填入对应栏内。[说明]RIP(Routing Information Protocols，路由信息协议)是使用最广泛的距离向量协议，它是由施乐(Xerox)在70年代开发的。当时，RIP是XNS(Xerox Network Service，施乐网络服务)协议簇的一部分。TCP/IP版本的RIP是施乐协议的改进版。RIP最大的特点是无论实现原理还是配置方法，都非常简单。以下是RIP配置的部分清单。Router＞enable (1)Enter configuration commands，one per line．End with CNTL/Z． (2)Router (config) interfacee 0/1 (3)Router (config-if) ipaddress172.16.1.2 255.255.255.0Router (config-if)//为了便于配置和记忆，还可以给每个端口添加一些描述信息。如下所示，在端口局部配置模式下使用description命令。Router ( config-if ) description connect to CIU (8)Router (config-if) endRouter......Routercopy mnning-config startup-config (12)Building configuration...[OK]Router......Router (config) linc console 0 (17)Router (config-line) login (18)Router (config-line) password cisco (19)Router (config-line) exit (20)Router (config) line vty 0 4 (21)Router (config-line) login (22)Router (config-line) password cisco (23)Router (config-line) exit (24)Routerping 192.168.4.2Type escape sequence to abort.Sending 5, 100-byte ICMP Ethos to 192.168.4.2, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5) , round-trip min/avg/max = 24/25/28 msRoutertraceroute 192.168.4.2Type escape sequence to abort.Tracing the route to 192.168.4.21 192.168.2.2 16 msec 16 msecRoutertelnet 192.168.4.2Trying 192.168.4.2 ... OpenUser Access VerificationPassword:Router ＞Routerdebug ip rip (41)RIP protocol debugging is onRouter请解释第(8)、(12)、(41)行的意义及(17)～(20)与(21)～(24)行的作用。
Which command will delete the current rescue configuration?() A. user@router# system delete configuration rescueB. user@router request system configuration rescue deleteC. user@router# delete rescue configurationD. user@router file delete rescue-configuration
ThenetworksetupforthistroubleticketisshowninFigure3.TroubleTicketStatementDSW1andR4cannotpingR2’sloopbackorR2’ss0/0/0/0.12IPv6address.InitialtroubleshootingshowsandR2isnotanOSPFv3neighboronR3.ConfigurationonR2ipv6unicast-routing!ipv6routerospf6router-id2.2.2.2!interfaces0/0/0/0.23ipv6address2026：：1：1/122ConfigurationR3ipv6unicast-routing!ipv6routerospf6router-id3.3.3.3!interfaces0/0/0/0.23ipv6address2026：：1：2/122ipv6ospf6area0Figure3OnWhichdeviceisthefaultconditionlocated?（）
What is the most likely reason for the dispartly between the actual network numbers at the branches and the routes in the routing table on Gateway－Router?() A. Branch-Router2 is configured to send both RIPv1 and RIPv2 updates.B. Gateway-Router is configured to only receive RIPv2 updates.C. Gateway-router is configured to receive only RIPv1 updates.D. Branch-Router1 is configured to only send RIPv1 updates
ThefollowingcommandisissuedonaCiscoRouter:Router(configuration)loggingconsolewarningsWhichalertswillbeseenontheconsole?() A.WarningsonlyB.debugging，informational，notifications，warningsC.warnings，errors，critical，alerts，emergenciesD.notifications，warnings，errorsE.warnings，errors，critical，alerts
What is themostlikelyreasonforthedispartlybetweentheactualnetworknumbersatthebranchesandtheroutesintheroutingtableonGateway－Router?() A.Branch-Router2isconfiguredtosendbothRIPv1andRIPv2updates.B.Gateway-RouterisconfiguredtoonlyreceiveRIPv2updates.C.Gateway-routerisconfiguredtoreceiveonlyRIPv1updates.D.Branch-Router1isconfiguredtoonlysendRIPv1updates.
如果要对 RIP进行调试排错，应该使用哪一个命令（） 。A．Router#debug ip ripB．Router(config)#debug ip ripC．Router#show router rip eventD．Router(config)#show ip interface
如果要对 RIP进行调试排错，应该使用哪一个命令（）。A．Router(config)#debug ip ripB．Router#show router rip eventC．Router(config)#show ip interfaceD．Router#debug ip rip