Identify the channel settings that can be performed using the CONFIGURE CHANNEL or ALLOCATECHANNEL commands in RMAN() (choose all that apply) A. Limiting the input/output (I/O) bandwidth consumptionB. Specifying the size of backup sets and backup piecesC. Specifying vendor-specific information for a media managerD. Specifying the parallelism for backup and restore operations
Identify the channel settings that can be performed using the CONFIGURE CHANNEL or ALLOCATECHANNEL commands in RMAN() (choose all that apply)
A. Limiting the input/output (I/O) bandwidth consumption
B. Specifying the size of backup sets and backup pieces
C. Specifying vendor-specific information for a media manager
D. Specifying the parallelism for backup and restore operations
相关考题：
关于无缓冲和有冲突的channel,下面说法正确的是() A. 无缓冲的channel是默认的缓冲为1的channelB. 无缓冲的channel和有缓冲的channel都是同步的C. 无缓冲的channel和有缓冲的channel都是非同步的D. 无缓冲的channel是同步的，而有缓冲的channel是非同步的
AVIOserverhastwofibrechanneladapters,fcs0fcs1,attachedforredundantaccesstoastoragesubsystem.Iffcs1hasfailed,whatisthecorrectproceduretorectifythisproblem?() A.Using’diagmenu’command，setfcs1toDefined.B.Using’oem_setup_env’and’rmdev-R’commands，setfcs1adapterto’Defined’state.C.Using’diagmenu’command，setthefcs1statetoDefinedD.Using’oem_setup_env’and’rmdev-dl’commands，setthestateoffcs1toDefined
Which channel is designated for VHF Digital Selective Calling?A.Channel 70B.Channel 06C.Channel 13D.Channel 16
要启用LACP并将交换机端口加入端口信道1,可使用下面哪两个命令之一?() A.Switch(config)#interface port-channel1B.Switch(config)#channel-group 1 mode activeC.Switch#interface port-channel 1D.Switch(config-if)#channel-group 1 mode active
WhatinterfaceiscreatedwhenanFCPortChanneliscreatedonaCiscoUnifiedComputingSystem?() A.Aninterface’san-port-channel’inNXOSB.Aninterface’port-channel’inNXOSC.Aninterface’port-channel’with’modefc’configuredD.Aninterface’fc-port-channel’inNXOS
WhichportchannelcommandisrecommendedforN1KVonCiscoUCS?() A.channel-groupautomodeonB.channel-groupautomodeactiveC.channel-groupautomodeonsub-groupcdpD.channel-groupautomodeonsub-groupmanualE.channel-groupautomodeonmac-pinning
根据以下的配置，请判断当主接口serial0出故障后，哪一个备份接口最先被启用？（）[Quidway-Serial0]standby interface serial 1 30[Quidway-Serial0]standby interface serial 2 40[Quidway-Serial0]standby logic-channel 3 50[Quidway-Serial0]standby logic-channel 2 35A.serial 1B.serial 2C.logic-channel 2D.logic-channel 3
哪条命令将开始捆绑两个物理接口来通过 LACP 创建 EtherChannel 组？A．channel-group 2 mode autoB．interface port-channel 2C．channel-group 1 mode desirableD．interface range GigabitEthernet 0/4 - 5
网络管理员通过使用命令 SW1（config-if-range)# channel-group 1 mode passive 来配置交换机 SW1 和 SW2 之间的 EtherChannel 链路。必须在 SW2 上使用哪个命令来启用此 EtherChannel？（）A．SW2(config-if-range)# channel-group 1 mode activeB．SW2(config-if-range)# channel-group 1 mode desirableC．SW2(config-if-range)# channel-group 1 mode autoD．SW2(config-if-range)# channel-group 1 mode passive