In the exhibit, there are four static routes that route traffic through different interfaces.Which interface does the router use if traffic is sent to the 99.0.0.1 destination?() A. ge-0/0/1B. ge-0/0/2C. ge-0/0/3D. ge-0/0/4
In the exhibit, there are four static routes that route traffic through different interfaces.Which interface does the router use if traffic is sent to the 99.0.0.1 destination?()
A. ge-0/0/1
B. ge-0/0/2
C. ge-0/0/3
D. ge-0/0/4
相关考题：
【问题2】（3分）根据图4-1的配置，补充完成下面路由器的配置命令：Router（config）# interface （3）Router（config-if）#ip address 10.10.1.1 255.255.255.0Router（config-if）#no shutdownRouter（config-if）#exitRouter（config）# interface （4）Router（config-if）# ip address 192.168.1.1 255.255.255.0Router（config）# interface （5）Router（config-if）# ip address 10.10.2.1 255.255.255.0
Whichcommandisneededtochangethispolicytoatunnelpolicyforapolicy-basedVPN？（）[editsecuritypoliciesfrom-zonetrustto-zoneuntrust]user@hostshowpolicytunnel-traffic{match{source-addresslocal-net；destination-addressremote-net；applicationany；then{permit；}}A.setpolicytunnel-trafficthentunnelremote-vpnB.setpolicytunnel-trafficthenpermittunnelremote-vpnC.setpolicytunnel-trafficthentunnelipsec-vpnremote-vpnpermitD.setpolicytunnel-trafficthenpermittunnelipsec-vpnremote-vpn
Which configuration command configures queue buffer allocation on the ERX Edge Router?() A.qos-profileB.queue-profileC.scheduler-profileD.traffic-shape-profile
You are troubleshooting a routing issue and need to check the hop－by－hop path to the 10.10.10.10 destination. Which three commands would display the path?() A. user@router# traceroute 10.10.10.10B. user@router ping record-route 10.10.10.10C. user@routertraceroute 10.10.10.10D. user@router# run traceroute 10.10.10.10E. user@router# ping record-route 10.10.10.10
When using OSPF as your IGP, which operational command must be enabled to populate the TED forCSPF calculations?() A. cspf enableB. disable no-cspfC. traffic-engineeringD. enable traffic-engineering-database
An engineer is reviewing another engineer‘s sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）A. tunnel sourceB. tunnel destinationC. tunnel modeD. All these commands are requireD
WhichofthefollowingcommandswillcauseRIPngtooriginateadefaultrouteadvertisementwhilesuppressingallotherroutes?() A.Rl（config-if）#ipv6default-informationoriginateB.Rl（config-router）#ipv6rip〈process-name〉default-informationonlyC.Rl（config）#ipv6route：：/0null0D.Rl（config-if）#ipv6rip〈process-name〉default-informationonlyE.Rl（config-router）#ipv6riproute；：/0originateF.Rl（config-router）#aggregate-address：：/0summarize-routes
What Netflow component can be applied to an interface to track IPv4 traffic?() A.flow monitorB.flow recordC.flow samplerD.flow
OSPF is a link-state routing protocol。It is designed to be run internal to a single （）system。Each OSPF router maintains an identical （）describing the autonomous system’s topology。From this database，a routing table is calculated by constructing a shortest-path （）。OSPF recalculates routes quickly in the face of topological changes，utilizing a minimum of routing （） traffic。OSPF provides support for equal-cost multipath。An area routing capability is provided，enabling an additional level of routing protection and a reduction in routing protocol （75）。A.flow B.state C.traffiC.D.stream