单选题在Catalyst 6500交换机上将端口3/1～3/24的传输速率设置为1Gbit/s，正确的配置是（ ）。Aset port speed 3/1—3/241000000Bset port speed 3/1241000000Cset port speed 3/1—3/241000Dset port speed 3/1—241000
单选题
在Catalyst 6500交换机上将端口3/1～3/24的传输速率设置为1Gbit/s，正确的配置是（ ）。
A
set port speed 3/1—3/241000000
B
set port speed 3/1241000000
C
set port speed 3/1—3/241000
D
set port speed 3/1—241000
参考解析
解析：
配置交换机端口的传输速率，Catalyst 6500交换机的命令格式为
set port speed<mod/port>auto Set speed to auto
set port speed<mod/port><port_speed>或速率的单位为Mbit/s，1Gbit/s=1000Mbit/s，因此选D项。
配置交换机端口的传输速率，Catalyst 6500交换机的命令格式为
set port speed<mod/port>auto Set speed to auto
set port speed<mod/port><port_speed>或速率的单位为Mbit/s，1Gbit/s=1000Mbit/s，因此选D项。
相关考题：
在Catalyst6500交换机上将端口3/1~ 3/24的传输速率设置为1Gbps，正确的配置是( )。A) set port speed 3/1-3/24 1000000B) set port speed 3/1-24 1000000C) set port speed 3/1-3/24 1000D) set port speed 3/1-24 1000
Cisco Catalyst 6500交换机的3/1端口与一台其他厂商的交换机相连，并要求该端口工作在VLANTrunk模式。这两台交换机的Trunk端口都应封装的协议和Cisco Catalyst 6500设置Traank模式的正确配置语句分别是______。A．ISL和set 3/1 trunk on islB．ISL和set trunk 3/1 on islC．IEEE 802.1Q和set tramk 3/1 on dotlqD．IEEE 802.1Q和set 3/1 trunk on dotlq
设置Catalyst 6500交换机的3/1至3/24端口为全双工通信方式，正确的配置语句是A．set interface duplex 3/1-3/24 fullBB．set interface duplex 3/1-24 fullC．set port duplex 3/1-3/24 fullD．set port duplex 3/1-24 full
Cisco Catalyst 6500 交换机的 3/1 端口与一台其他厂商的交换机相连，并要求该端口工作在 VLAN Trunk 模式 .这两台交换机的 trunk 端口都应封装的协议和 Cisco Catalyst6500 设置 trunk 模式的正确配置语句是A ） ISL 和 set 3/1 trunk on islB ） ISL 和 set trunk 3/1 on islC ） IEEE802.1Q 和 set trunk 3/1 on dotlqD ） IEEE802.1Q 和 set 3/1 trunk on dotlq
将Cisco 6500第4模块第1端口的通信方式设置为半双工，第2～24端口的通信方式设置为全双工，以下交换机的端口配置，正确的是A）Switch-6500 (enable) set interface duplex 4/1 halfSwitch-6500 (enable) set interface duplex 4/2-24 fullB）Switch-6500 (enable) set port 4/1 duplex halfSwitch-6500 (enable) set port 4/2-24 duplex fullC）Switch-6500 (enable) set port duplex 4/1 halfSwitch-6500 (enable) set port duplex 4/2-4/24 fullD）Switch-6500 (enable) set port duplex 4/l halfSwitch-6500 (enable) set port duplex 4/2-24 full
将Catalyst 6500交换机第3个模块的端口1～端口8设置为全双工通信方式，正确的配置语句是______。A．Switch-PHY-6500(config-if)#duplex fullB．Switch-PHY-6500(config-if)#duplex 3 1-8 fullC．Switch-PHY-6500＞(enable) set port duplex 3/1-8 fullD．Switch-PHY-6500＞(enable) set port duplex 3 1-8 full
请填写以下Cisco 6500交换机STP配置命令的描述。set spantree enable[vlan] (1)set spantree fwddelay delay[vlan] (2)set spantree hello interval[vlan] (3)set spantree maxage agingtime[vlan] (4)set spantree portcost mod_num／port_num cost (5)
请填写以下Cisco 6500交换机端口配置命令的描述。set port name mod_num／port_num[name_string] (1)set port level mod—num／port_num noramal I high (2)set port speed mod_num／port_num1011001auto (3)set port duplex mod_num／port_num fullIhalf (4)show port mod_num／port_num (5)
配置STP协议时，为选择交换机的根端口，不需要比较以下(52)参数。A．Root IDB．Designated Bridge IDC．Designated Port IDD．Port Speed
将Cise0 6500第4模块第1端口的通信方式设置为半双工，第2-24端口的通信方式设置为全双工，以下交换机的端口配置，正确的是（ ）。A.Switch-6500>；（enable）set interface duplex 4/1 halfSwitch-6500>；（enable）set interface duplex 4/2-24 fullB.Switch-6500>；（enable）set port 4/1 duplex halfSwitch-6500>；（enable）set port 4/2-24 duplex fullC.Switch-6500>；（enable）set port duplex 4/1 halfSwitch-6500>；（enable）set port duplex 4/2-4/24 fullD.Switch-6500>；（enable）set port duplex 4/1 halfSwitch-6500>；（enable）set port duplex 4/2-24 full
PCA、PCB 分别与交换机 SWA 的端口 Ethernet1／0／2、Ethernet1／0／3 相连,服务器与端口Ethernet1／0／1 相连。如果使用端口隔离技术使 PC 间互相隔离,但 PC 都能够访问服务器,则需要在交换机上配置哪些命令? () A. [SWA] port-isolate enableB. [SWA-Ethernet1/0/2] port-isolate enableC. [SWA-Ethernet1/0/3] port-isolate enableD. [SWA-Ethernet1/0/1] port-isolate uplink-port
A.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/3 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE TRUNK [SWITCHA-GIGABITETHERNET1/0/3] PORT TRUNK ALLOW-PASS VLAN 2 3 B.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/1 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE TRUNK [SWITCHA-GIGABITETHERNET1/0/3] PORT TRUNK ALLOW-PASS VLAN 2 3 C.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/1 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE ACCESS [SWITCHA-GIGABITETHERNET1/0/3] PORT DEFAULT VLAN 2 3 D.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/3 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE ACCESS [SWITCHA-GIGABITETHERNET1/0/3] PORT DEFAULT VLAN 2 3
PCA、PCB分别与S3610交换机SWA的端口Ethernet1/0/2、Ethernet1/0/3相连，服务器与端口Ethernet1/0/1 相连。如果使用端口隔离技术使PC间互相隔离，但PC都能够访问服务器，则需要在交换机上配置哪些命令？（）A、[SWA] port-isolate enableB、[SWA-Ethernet1/0/2] port-isolate enableC、[SWA-Ethernet1/0/3] port-isolate enableD、[SWA-Ethernet1/0/1] port-isolate uplink-port
PCA、PCB分别与S3610交换机SWA的端口Ethernet1/0/2、Ethernet1/0/3相连，服务器与端口Ethernet1/0/1相连。如果使用端口隔离技术使PC间互相隔离，但PC都能够访问服务器，则需要在交换机上配置哪些命令？（）A、[SWA]port-isolateenableB、[SWA-Ethernet1/0/2]port-isolateenableC、[SWA-Ethernet1/0/3]port-isolateenableD、[SWA-Ethernet1/0/1]port-isolateuplink-port
Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software?（）A、show port networkB、 show running-configC、show controllers Ethernet-controllerD、 show interfaces
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）A、 The speed of the slowest interface in the port channelB、 The combined speed of all interfaces configured in the port channelC、 The combined speed of all interfaces in the port channel that are upD、 The speed that can be achieved if all buffers are used
A new system has been installed and the network connection is very slow. The network administrators are sure that the network port is set to 100 full duplex. What command will display the configured and current speed settings of the adapter?（）A、lsdevB、lsattrC、entstatD、ifconfig
单选题Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）A The speed of the slowest interface in the port channelB The combined speed of all interfaces configured in the port channelC The combined speed of all interfaces in the port channel that are upD The speed that can be achieved if all buffers are used
单选题Cisco Catalyst 6500交换机的3/1端口与一台其他厂商的交换机相连，并要求该端口工作在VLAN Trunk模式，这两台交换机的trunk端口都应封装的协议和Cisco Catalyst6500设置trunk模式的正确配置语句是（ ）。AISL和set 3/1 trunk on is1BISL和settnmk 3/1 on is1CIEEE 802.1Q和set trunk 3/1 on dotlqDIEEE 802.1Q和set 3/1 trunk on dotlq
单选题在Catalyst6500交换机上将端口3/1～3/24的传输速率设置为1Gbps，正确的配置是（ ）。Aset port speed 3/1-3/24 1000000Bset port speed 3/1-24 1000000Cset port speed 3/1-3/24 1000Dset port speed 3/1-24 1000
单选题A new system has been installed and the network connection is very slow. The network administrators are sure that the network port is set to 100 full duplex. What command will display the configured and current speed settings of the adapter?（）AlsdevBlsattrCentstatDifconfig
单选题设置Catalyst 6500交换机的3/1至3/24端口为全双工通信方式，正确的配置语句是（ ）。Aset interface duplex 3/1—3/24 fullBset interface，duplex 3/1—24 fullCset port duplex 3/1—3/24 fullDset port duplex 3/1—24 full
单选题Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software?（）Ashow port networkB show running-configCshow controllers Ethernet-controllerD show interfaces
单选题在Catalyst 6500交换机上将端口3/1至3/24的传输速率设置为1Gbit/s，正确的配置是（ ）。Aset port speed 3/1—3/24 1000000Bset pert speed 3/1—24 1000000Cset port speed 3/1—3/24 1000Dset port speed 3/1—24 1000