多选题When defining an application for AppFlow acceleration, which two must be configured on the WX device?（）(Choose two.)ADefine application type.BEnable AppFlow for the application.CEnable monitoring for the application.DDefine source and destination IP addresses.
多选题
When defining an application for AppFlow acceleration, which two must be configured on the WX device?（）(Choose two.)
A
Define application type.
B
Enable AppFlow for the application.
C
Enable monitoring for the application.
D
Define source and destination IP addresses.
参考解析
解析：
暂无解析
相关考题：
What are two requirements when using Packet Flow Acceleration? ()(Choose two.) A. Traffic needs be compressed.B. Quality of service must be enabled.C. A service tunnel must exist in at least one direction.D. PFA must be enabled on the client-side WX device.
Which two CIFS commands are accelerated by AppFlow? ()(Choose two.) A. ReadXB. Write AndXC. Trans2 QueryD. Tree Disconnect
What are two ways to verify if a WX device is configured as a hub, a spoke, or a mesh device? ()(Choose two.) A. Admin DeviceB. Device Setup TopologyC. Compression EndpointsD. Device Setup Advanced Topology
When defining an application for AppFlow acceleration, which two must be configured on the WX device?()(Choose two.) A. Define application type.B. Enable AppFlow for the application.C. Enable monitoring for the application.D. Define source and destination IP addresses.
Which two conditions will cause switch－to－wire to occur? ()(Choose two.) A. loss of powerB. QoS congestionC. software failure occuredD. WX device exceeded its license speedE. traffic does not match application definiton
Which two methods are used to assign an IP address to a WX device? ()(Choose two.) A. SSHB. TelnetC. WebViewD. device front panelE. serial console (command-line interface)
Which of the following are associated with the application layer of the OSI model (Choose two.)()。 A.pingB.TelnetC.FTPD.TCPE.IP
Which of the following are associated with the application layer of the OSI model (Choose two.)（）。A、pingB、TelnetC、FTPD、TCPE、IP
What are two requirements when using AppFlow?（） (Choose two.)A、Quality of service must be enabled.B、NSC compression must be enabled.C、PFA's TCP Acceleration (AFP) must be enabled.D、AppFlow must be configured on the client-side device first.
When defining an application for AppFlow acceleration, which two must be configured on the WX device?（）(Choose two.)A、Define application type.B、Enable AppFlow for the application.C、Enable monitoring for the application.D、Define source and destination IP addresses.
What are two ways to verify if a WX device is configured as a hub, a spoke, or a mesh device? （）(Choose two.)A、Admin DeviceB、Device Setup TopologyC、Compression EndpointsD、Device Setup Advanced Topology
Which two CIFS commands are accelerated by AppFlow? （）(Choose two.)A、ReadXB、Write AndXC、Trans2 QueryD、Tree Disconnect
Which two methods are used to assign an IP address to a WX device? （）(Choose two.)A、SSHB、TelnetC、WebViewD、device front panelE、serial console (command-line interface)
Which two conditions will cause switch-to-wire to occur? （）(Choose two.)A、loss of powerB、QoS congestionC、software failure occuredD、WX device exceeded its license speedE、traffic does not match application definiton
What are two requirements when using AppFlow? （）(Choose two.)A、Quality of service must be enabled.B、NSC compression must be enabled.C、PFA's TCP Acceleration (AFP) must be enabled.D、AppFlow must be configured on the client-side device first
Which two types of optimization does the WX 60 device perform when Exchange 2003 and Outlook 2003 areused in the network? （）(Choose two.)A、Packet Flow AccelerationB、Network Sequence CachingC、AppFlow's MAPI accelerationD、Molecular Sequence Reduction
Which statement is true regarding SMB signing and AppFlow CIFS acceleration?（）A、SMB signing is transparent to application performance.B、It is possible to perform CIFS acceleration when SMB signing is on.C、SMB assigns hash values to the packet, allowing CIFS acceleration to take place.D、SMB authenticates the WX service tunnel, allowing CIFS acceleration to be accomplished successfully.
Which three types of optimization does the WX 60 device perform when Exchange 2000 and Outlook 2000 are used in the network? （）(Choose three.)A、Fast Connection SetupB、TCP Acceleration (AFP)C、Network Sequence CachingD、AppFlow's MAPI accelerationE、Molecular Sequence Reduction
多选题Which of the following are associated with the application layer of the OSI model (Choose two.)（）。ApingBTelnetCFTPDTCPEIP
多选题When defining an application for AppFlow acceleration, which two must be configured on the WX device?（）(Choose two.)ADefine application type.BEnable AppFlow for the application.CEnable monitoring for the application.DDefine source and destination IP addresses.
多选题What are two ways to verify if a WX device is configured as a hub, a spoke, or a mesh device? （）(Choose two.)AAdmin DeviceBDevice Setup TopologyCCompression EndpointsDDevice Setup Advanced Topology
多选题What are two requirements when using AppFlow?（） (Choose two.)AQuality of service must be enabled.BNSC compression must be enabled.CPFA's TCP Acceleration (AFP) must be enabled.DAppFlow must be configured on the client-side device first.
多选题What are two requirements when using AppFlow? （）(Choose two.)AQuality of service must be enabled.BNSC compression must be enabled.CPFA's TCP Acceleration (AFP) must be enabled.DAppFlow must be configured on the client-side device first
多选题Which two methods are used to assign an IP address to a WX device? （）(Choose two.)ASSHBTelnetCWebViewDdevice front panelEserial console (command-line interface)
多选题Which two types of optimization does the WX 60 device perform when Exchange 2003 and Outlook 2003 areused in the network? （）(Choose two.)APacket Flow AccelerationBNetwork Sequence CachingCAppFlow's MAPI accelerationDMolecular Sequence Reduction
多选题Which two CIFS commands are accelerated by AppFlow? （）(Choose two.)AReadXBWrite AndXCTrans2 QueryDTree Disconnect
多选题Which two conditions will cause switch-to-wire to occur? （）(Choose two.)Aloss of powerBQoS congestionCsoftware failure occuredDWX device exceeded its license speedEtraffic does not match application definiton
多选题What are two requirements when using Packet Flow Acceleration? （）(Choose two.)ATraffic needs be compressed.BQuality of service must be enabled.CA service tunnel must exist in at least one direction.DPFA must be enabled on the client-side WX device.