为了查看路由器的E0端口上,是否挂接了访问权限表,应该使用的命令是()A.show access-listB.show interface e0C.show ipinterface e0D.show e0

为了查看路由器的E0端口上,是否挂接了访问权限表,应该使用的命令是()

A.show access-list

B.show interface e0

C.show ipinterface e0

D.show e0


相关考题:

在思科路由器上,应该使用什么命令来观察网络的路由表() A.Show ip pathB.Show ip routeC.Show interfaceD.Show running-config

为了确定配置的ISDN路由器接口状态,应该输入哪一条命令()。A.show interfaceB.show is dnq921C.show is dnq931D.show is dnstatusE.show is dnactive

为了查看Quidway路由器搭建的帧中继网络的封装类型,应使用什么命令()。A.show frame-relay mapB.show frame-relay pvcC.show frame-relay lmiD.show interface

要进人以太端口配置模式,下面的路由器命令中,哪一条是正确的?——A.Router#interface e0B.Router#line eoC.Router.(confi)删ne e0D.Router(config)#interface e0

查看路由表的命令是:()A.show interfaceB.show runC.show ip routeD.show table

查看E0端口配置信息的命令是:()A.show access-listB.show ip routeC.show versionD.show interfacee0

使用()命令可以显示默认带宽。 A.show interfacesB.clock rateC.no shutdoenD.interface serial

什么命令可查看访问列表是否应用到端口上()。 A.Show ip routeB.Show ip interfaceC.Show access-listD.Show access-group

路由器上察看路由表的命令是()。A.Show iprouteB.ARP–aC.TracertD.Route print

可以在特权用户模式下,使用( )命令查看配置文件、接口工作状态、路由表、缓冲区以及路由器的各种工作状态,以便验证路由器的配置是否正确和路由器的工作是否正常。

在本地路由表如下所示,路由器把目标地址为10.1.5.65的分组发送给( )。Network Interface Next-hop 10.1.1.0/24 e0 Directly connected 10.1.2.0/24 e1 Directly connected 10.1.5.0/24 s1 10.1.1.2 10.1.5.64/28 e0 10.1.2.2 10.1.5.64/29 s0 10.1.3.3 10.1.5.64/27 s1 10.1.4.4A.10.1.1.2 B.10.1.2. 2 C.10.1.3. 3 D.10.1.4. 4

若路由器R1和R2均使用静态路由,R1的e0接口的IP地址为217.14.8.1;R2的e0接口的IP地址为217.14.8.2,s0接口的IP地址是202.198.56.9/30。请填充R2的路由表(表3-2)。

When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?() A.show ip access-listB.show access-listC.list ip interfaceD.show interfaceE.show ip interface

为了查看Quidway路由器上的串口s0的封装是DTE或DCE,应该使用命令() A.show controllerserialB.show running-configC.show interfaces0D.show startup-config

Cisco路由器查看路由表信息的命令是______。A.show routeB.show routerC.show ip routeD.show ip router

为了相对温度增大,即△f0,要求()。A、Δe0,Δt0B、Δe0,Δt0C、Δe0,Δt0D、Δe0,Δt0

要查看一个Cisco路由器接口上是否有某些ACL,你该使用命令()A、show running-config;B、show ip protocols;C、show ip interface;D、show ip network。

查看H3C路由器端口状态使用()命令。A、telnetB、ip configC、show interfaceD、dis interface

在Quidway路由器上如何查看接口e0的IPX地址?()A、DISPLAY interfaceB、DISPLAY ipx interfaceC、DISPLAY ipx serversD、DISPLAY interface e0

为了查看Quidway路由器搭建的帧中继网络的封装类型,应使用什么命令?()A、show frame-relay mapB、show frame-relay pvcC、show frame-relay lmiD、show interface

为了查看路由器上串口S0/0/1是DTE接口还是DCE接口,应该使用下面哪个命令?()A、display controller serialB、display saved-configC、display interface s0/0/1D、display current-config

在思科设备上,若要查看所有访问表的内容,可以使用的命令式()A、show allaccess-listsB、show access-listsC、show ipinterfaceD、show interface

查看CISCO路由器端口状态使用()命令。A、telnetB、ip configC、show interfaceD、dis interface

为了查看Quidway路由器上的串口s0的封装是DTE或DCE,应该使用命令()A、DISPLAY controller serialB、DISPLAY running-configC、DISPLAY interface s0D、DISPLAY startup-config

单选题为了查看路由器上串口S0/0/1是DTE接口还是DCE接口,应该使用下面哪个命令?()Adisplay controller serialBdisplay saved-configCdisplay interface s0/0/1Ddisplay current-config

单选题什么命令可查看访问列表是否应用到端口上()。AShow ip routeBShow ip interfaceCShow access-listDShow access-group

单选题为了查看Quidway路由器搭建的帧中继网络的封装类型,应使用什么命令?()Ashow frame-relay mapBshow frame-relay pvcCshow frame-relay lmiDshow interface