单选题A client is configuring an x3650 M3. Once the system is in production， they need to able to remotely view and make changes to the UEFI interface. Which of the following is the correct way to configure this？（）AConfigure the RSA with an IP addressBConfigure the BMC with an IP addressCConfigure the AMM with an IP addressDConfigure the IMM with an IP address
单选题
A client is configuring an x3650 M3. Once the system is in production， they need to able to remotely view and make changes to the UEFI interface. Which of the following is the correct way to configure this？（）
A
Configure the RSA with an IP address
B
Configure the BMC with an IP address
C
Configure the AMM with an IP address
D
Configure the IMM with an IP address
参考解析
解析：
暂无解析
相关考题：
What is the likely cause of a system hanging at boot code 557?() A.The system is configuring network adapters.B.The system is configuring fibre channel devices.C.The system is unable to mount the rootvg filesystems.D.The system is unable to access the installation media.
A system was rebooted and is taking a long time toreturn. The administrator has logged into the HMC and sees reference code 0c9.What does this mean?() A.The system is configuring a device.B.A system initiated dump has started.C.The system is varyingon a volume group.D.The system is running an inbuilt self test.
If your passenger vessel is fitted with a loudspeaker system，it must be tested at least once ______.A.every weekB.a dayC.every tripD.a watch or once a trip，whichever is shorter
When configuring system state conditions with the Cisco SecurityAgent， what is the resulting action when configuring more than one system state condition？ （）A、Any matching state condition will result with the state being triggeredB、 Once a state condition ismet， the system ceases searching further conditions and will cause the state condition to triggerC、 All specified state conditions are used as part of the requirements tobe met to for the state to triggerD、 Once the state conditions are met， they become persistent and can only be removed using the Reset feature
What is the purpose of configuring the router as a PPPoE client?（）A、to provide VPN access over L2TPB、to enable PPP session from the router to the termination device at the headend for metro Ethernet connectivityC、for DSL connectivity and removing the need for the end - user PC to ru n the PPPoE client softwareD、for connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable modem termination system
Your best customer calls in with a last-minute need for the BTU/HR or the heat output per server， per hour for a rack of x3650 servers. What IBM tool will you use to get your answer quickly？（）A、System x Sales Configuration Aid （xSCA）B、BladeCenter System x Power ConfiguratorC、Configuration Options Guide - （COG）D、IBM Sizing Guides
When configuring more than one archival site, which statement is true?（）A、The system will first attempt the transfer using the URL configured lastB、The system will transfer the configuration to each archival siteC、The system will not transfer to a secondary site unless the previous site failsD、The system will transfer using secure copy protocl (SCP) before attempting FTP
A customer has requested the most cost-effective p5 solution allowing for growth. Which of the following should the pSeries technical specialist consider doing when configuring each p5 system using eConfig？（）A、Implementing CoDB、Using Express Configurations with processor upgradesC、Meeting the minimum Value Pak rulesD、Engaging the pSeries representative to identify appropriate discounts
A "trusted" client needs to communicate with a server that has been configured to use CLIENT authentication. Which of the following will be used to verify passwords?（）A、User ID/password fileB、Communications layerC、Client applicationsD、Operating system
A system administrator for a business recovery service center needs to test disaster recovery strategies for their clients running Linux. Each client has a different system configuration. Each time a client comes in, the system configuration of the managed system must change. What is the best way to handle this using LPAR?（）A、Create a system profile. Reconfigure the managed system by activating and deactivating the system profiles. B、Create one partition profile for each client. Reconfigure the managed system by activating the partition profiles for that client. C、Dynamically move processors and memory as needed into each logical partition. Reconfigure the managed system by activating and deactivating partition profiles. D、Dynamically move processors and memory into each logical partition on the server if additional resources are needed. Reconfigure the managed system by activating and deactivating the system profiles.
What is the likely cause of a system hanging at boot code 557?（）A、The system is configuring network adapters.B、The system is configuring fibre channel devices.C、The system is unable to mount the rootvg filesystems.D、The system is unable to access the installation media.
A customer purchases a virtual media key on a x3650 M3. They ask where to install the key. Which of the following provides the correct answer？（）A、Problem Determination and Service GuideB、xRefC、ServerGuide Hardware ReferenceD、COG
A system administrator is installing a p5 590 server with an HMC. After pulling the websm client down, it is not possible to connect to the HMC. The HMC can be pinged from the client. Which of the following settings should be verified next?（）A、The routes on the HMCB、The firewall setting of the LAN adapterC、The name resolution protocol on the p5 590 serverD、The subnet mask settings on the Ethernet adapters
When configuring the messaging system， which of the following are valid parameters for the file transport？ （）A、File NameB、Operating SystemC、LocationD、HostE、Mode
A system was rebooted and is taking a long time toreturn. The administrator has logged into the HMC and sees reference code 0c9. What does this mean?（）A、The system is configuring a device.B、A system initiated dump has started.C、The system is varyingon a volume group.D、The system is running an inbuilt self test.
A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）A、A public internet connectionB、All of the Logical Partitions need to be activeC、One partition must be configured with Service AuthorityD、A local Repository must be configured prior to the update
单选题If your passenger vessel is fitted with a loudspeaker system，it must be tested at least once （）.Aevery weekBa dayCevery tripDa watch or once a trip，whichever is shorter
单选题A system administrator is installing a p5 590 server with an HMC. After pulling the websm client down, it is not possible to connect to the HMC. The HMC can be pinged from the client. Which of the following settings should be verified next?（）AThe routes on the HMCBThe firewall setting of the LAN adapterCThe name resolution protocol on the p5 590 serverDThe subnet mask settings on the Ethernet adapters
单选题When configuring system state conditions with the Cisco SecurityAgent， what is the resulting action when configuring more than one system state condition？ （）AAny matching state condition will result with the state being triggeredB Once a state condition ismet， the system ceases searching further conditions and will cause the state condition to triggerC All specified state conditions are used as part of the requirements tobe met to for the state to triggerD Once the state conditions are met， they become persistent and can only be removed using the Reset feature
单选题What is the purpose of configuring the router as a PPPoE client?（）Ato provide VPN access over L2TPBto enable PPP session from the router to the termination device at the headend for metro Ethernet connectivityCfor DSL connectivity and removing the need for the end - user PC to ru n the PPPoE client softwareDfor connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable modem termination system
单选题Rate your level of proficiency with configuring and troubleshooting access to files and shared folders,configuring file system permissions, and troubleshooting Terminal Services. （）AVery HighBHighCModerateDLowEVery Low
多选题When configuring the messaging system， which of the following are parameters of the e-mail transport？ （）ALocationBProtocolCModeDWeb AddressEHost
单选题A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）AA public internet connectionBAll of the Logical Partitions need to be activeCOne partition must be configured with Service AuthorityDA local Repository must be configured prior to the update
单选题What is the likely cause of a system hanging at boot code 557?（）AThe system is configuring network adapters.BThe system is configuring fibre channel devices.CThe system is unable to mount the rootvg filesystems.DThe system is unable to access the installation media.
单选题What should you set the Client Configuration to when configuring the ODBC Data Source for the Database Subsystem?（）ATCP/IP BMultiprotocol CNamed Pipes DNWLink IPX/SPX
单选题Your network consists of an Active Directory Domain Services （AD DS） forest with 1，000 client computers that run Windows XP. Nine hundred of the computers are on the local area network. One hundred computers are portable computers that connect to the main office only once every few months. You are planning to deploy Windows 7. You need to generate a report of the software that is installed on all client computers. You need this information as soon as possible. What should you use？（）AMicrosoft System Center EssentialsBMicrosoft Desktop Optimization PackCMicrosoft System Center Operations ManagerDMicrosoft System Center Data Protection Manager