单选题Which parameter， when enabled on a standalone access point， gives the highest priority to a voice packet even when qos is not enabled？（）Aigmp snoopingBwmmCqos element for wireless phonesDavvid priority mapping
单选题
Which parameter， when enabled on a standalone access point， gives the highest priority to a voice packet even when qos is not enabled？（）
A
igmp snooping
B
wmm
C
qos element for wireless phones
D
avvid priority mapping
参考解析
解析：
暂无解析
相关考题：
The AirMagnet passive site survey tool can provide RF coverage data， except for which parameter？（）A、Signal strength （4th access point）B、Signal strength （3rd access point）C、Channel interferenceD、Predictive physical data rate downlink （2nd access point）
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning. What needs to be enabled on the standalone access point tocorrect this issue？（）A、a shared keyB、network EAPC、open authentication plus EAPD、open authentication plus MAC
Using the WLSE， you are trying to push out a configuration job to a standalone access point， butthe job does not start. Which of the following would cause this failure？（）A、invalid parameter in the templateB、incorrect SNMP communities on the access pointC、pop-up blocker enabled in the browserD、unsupported version of IOS firmware in the access point
Using the WLSE，you are trying to push out a configuration job to an access point，but the job doesnot start. Which of the following would cause this failure？（）A、invalid parameter in the templateB、incorrect SNMP communities on the access pointC、unsupported version of IOS firmware in the access pointD、pop-up blocker enabled in the browser
Which parameter， when enabled on a standalone access point， gives the highest priority to a voice packeteven when QoS is not enabled？（）A、QoS Element for Wireless PhonesB、IGMP SnoopingC、WMMD、AVVID Priority Mapping
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped. What may cause this problem？（）A、The minimum data rate is not set to 11 Mbps.B、An address resolution protocol is enabled.C、Publicly Secure Packet forwarding is enabled.D、The access point is set to the least congested channel.
You are troubleshooting a problem with a cisco 7920 wireless ip phone on a standalone wlan. the phone rings but， when you Answer ，the call is dropped. What may have caused this problem？（）A、publicly secure packet forwarding is enabled.B、the minimum data rate is not set to 11 mbps.C、an address resolution protocol is enabled.D、the access point is set to the least congested channel.
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） isfailing， but association using EAP-PEAP is functioning. What needs to be enabled on the standalone accesspoint to correct this issue？（）A、network EAPB、open authentication plus MACC、open authentication plus EAPD、a shared key
多选题Access Point R1 is an Aironet 1200 that has been converted from autonomous mode to LWAPP mode. After this conversion， which two statements are true？ （）ALWAPP-enabled access points can still communicate with Wireless Domain Services （WDS） devices.BAn LWAPP-enabled access point console port provides read-only access to the unit.CLWAPP-enabled access points support Layer 2 LWAPP.DLWAPP-enabled access points must get an IP address and discover the controller using DHCP， DNS， or an IP subnet broadcast.EAn LWAPP-enabled access point console port provides read-write access to the unit.
单选题To which parameter should the access point be set during a site survey？（）ATransmit onlyBDiversityCReceive onlyDSingle isolated antenna
单选题In a deployment using standalone access points， clients set up to authenticate with EAP-PEAP or EAP-Cisco Wireless （Cisco-LEAP） cannot authenticate. When you inspect the Failed Attempts report on theCisco Secure ACS， you find this error： "Unknown network access server NAS." Which problem may havecaused this failure？（）Amisconfigured EAP type on the access pointBmisconfigured EAP type on the AAA serverCmisconfigured IP address of the access point on the AAA serverDmisconfigured IP address of the AAA server on the access point
单选题On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning. What needs to be enabled on the standalone access point tocorrect this issue？（）Aa shared keyBnetwork EAPCopen authentication plus EAPDopen authentication plus MAC
单选题You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped. What may cause this problem？（）AThe minimum data rate is not set to 11 Mbps.BAn address resolution protocol is enabled.CPublicly Secure Packet forwarding is enabled.DThe access point is set to the least congested channel.
单选题Using the WLSE， you are trying to push out a configuration job to a standalone access point， but the jobdoes not start. Which of the following would cause this failure？（）Ainvalid parameter in the templateBpop-up blocker enabled in the browserCincorrect SNMP communities on the access pointDunsupported version of IOS firmware in the access point
多选题When assigning a standalone access point a non-root role， which two parameters， other than Rolein the radio network settings， must be configured on the SSID Manager page？（）AForce Infrastructure Devices to associate only to this SSIDBSet Infrastructure SSIDCMultiple BSSIDDSet Data Beacon RateEEnable IP redirection on this SSID